Contents
- Whereas, pursuant to subsection 332(1) of the Canadian Env…
- Interpretation
- Application
- Maximum VOC Concentrations and Maximum VOC Emission Potentials
- VOC Compliance Unit Trading System
- Permit — Products Whose Use Results in Lower VOC Emissions
- Permit — Technical or Economic Non-feasibility
- Accredited Laboratory
- Labelling
- Record-Keeping
- Submission Requirements
- Related Amendment to the Regulations Designating Regulatory Provisions for Purposes of Enforcement (Canadian Environmental Protection Act, 1999)
- Coming into Force
- Schedule 1 Product Categories and VOC Concentration Limits (Subsections 1(1) and (4), 2(1) and 3(1) and (3), paragraph 3(4)(a), sections 4, 5 and 7, subsection 8(1), subparagraphs 8(2)(c)(ii) and (v) and 11(1)(c)(ii), subsection 11(2), paragraph 13(d), subparagraph 14(c)(ii), subsection 15(1), paragraphs 15(2)(d) and (h), subsection 16(1), paragraph 17(1)(a), subsection 18(1), paragraphs 18(2)(d), (i) and (j), subsection 19(1), sections 22 and 23 and subsection 24(1))
- Schedule 2 Product Categories and Maximum VOC Emission Potentials (Subsections 1(4), 2(1) and 3(2), paragraph 6(b), subsection 18(1), paragraphs 18(2)(d), (e), (i) and (j) and subsections 19(1), 22(1) and 24(1))
Whereas, pursuant to subsection 332(1) of the Canadian Environmental Protection Act, 1999, the Minister of the Environment published in the Canada Gazette, Part I, on July 6, 2019, a copy of the proposed Volatile Organic Compound Concentration Limits for Certain Products Regulations, substantially in the annexed form, and persons were given an opportunity to file comments with respect to the proposed Regulations or to file a notice of objection requesting that a board of review be established and stating the reasons for the objection;notenoteWhereas, pursuant to subsection 93(3) of that Act, the National Advisory Committee has been given an opportunity to provide its advice under section 6 of that Act;noteAnd whereas, in the opinion of the Governor in Council, pursuant to subsection 93(4) of that Act, the proposed Regulations do not regulate an aspect of a substance that is regulated by or under any other Act of Parliament in a manner that provides, in the opinion of the Governor in Council, sufficient protection to the environment and human health;Therefore, Her Excellency the Governor General in Council, on the recommendation of the Minister of the Environment and the Minister of Health, pursuant to subsection 93(1) and sections 286.1 and 326 of the Canadian Environmental Protection Act, 1999, makes the annexed Volatile Organic Compound Concentration Limits for Certain Products Regulations.note
Interpretation
1Definitions#
(1)The following definitions apply in these Regulations.
fragrance means a substance or mixture of chemicals, natural essential oils or other components, that has a combined vapour pressure that is less than or equal to 0.267 kPa when measured at 20°C, the sole purpose of which is to impart a scent or to mask an unpleasant odour. (parfum)
high vapour pressure VOC, in respect of an antiperspirant or deodorant for the human axilla, means a VOC that has a vapour pressure of greater than 10.67 kPa when measured at 20°C. (COV à pression de vapeur élevée)
low vapour pressure VOC, in respect of a product other than an antiperspirant or deodorant for the human axilla, means a VOC that
(a)has a vapour pressure of less than 0.013 kPa when measured at 20°C;
(b)has a boiling point that is greater than 216°C; or
(c)contains more than 12 carbon atoms per molecule. (COV à faible pression de vapeur)
medium vapour pressure VOC, in respect of an antiperspirant or deodorant for the human axilla, means a VOC that has a vapour pressure of greater than 0.267 kPa but less than or equal to 10.67 kPa when measured at 20°C. (COV à pression de vapeur moyenne)
reformulated product means a product that belongs to a product category set out in column 1 of the table to Schedule 1 and that has been reformulated to reduce its VOC concentration to a level that is less than the maximum VOC concentration set out in column 3 for that product category or, if applicable, the subcategory set out in column 2 to which it belongs. (produit à composition modifiée)
VOC means a volatile organic compound that participates in atmospheric photochemical reactions and that is not excluded under item 65 of Schedule 1 to the Canadian Environmental Protection Act, 1999. (COV)
(2)For the purpose of these Regulations, the VOC concentration of a product is measured and expressed as a percentage of the product’s net weight (% w/w).
(3)For the purposes of these Regulations, the quantity of a product or the quantity of VOCs in a product is the net quantity.
(4)For the purposes of these Regulations, a product belongs to a product category set out in column 1 of the table to Schedule 1 or column 1 of Schedule 2 or, if applicable, a subcategory set out in column 2 of the table to Schedule 1 if, according to information on its container or included in any documentation relating to the product that is supplied by the product’s manufacturer or importer or their authorized representative, the product may be used as a product that belongs to that product category or, if applicable, subcategory.
(5)For the purposes of these Regulations, any reference to a product that is designed for a particular purpose includes a product that, according to information on its container or included in any documentation relating to the product that is supplied by the product’s manufacturer or importer or their authorized representative, may be used for that purpose.
Application
2Products#
(1)These Regulations apply in respect of any product that contains VOCs and belongs to a product category set out in column 1 of the table to Schedule 1 or column 1 of Schedule 2.
(2)These Regulations do not apply in respect of products that are
(a)designed to be used solely in a manufacturing or processing activity;
(b)to be used solely in a laboratory for analysis, in scientific research or as a laboratory analytical standard;
(c)regulated under the Pest Control Products Act;
(d)manufactured or imported for export only;
(e)adhesives that are to be sold in containers of 30 ml or less;
(g)used in or on a new car at the time of its manufacture; or
(h)in transit through Canada, from a place outside Canada to another place outside Canada.
Maximum VOC Concentrations and Maximum VOC Emission Potentials
3Prohibition#
(1)Subject to subsection (4), a person must not manufacture or import a product that belongs to a product category set out in column 1 of the table to Schedule 1 and, if applicable, a subcategory set out in column 2 that has a VOC concentration that is greater than the applicable maximum VOC concentration set out in column 3, unless
(a)the product is, according to the instructions set out in both official languages on the product’s container or in any accompanying documentation, to be diluted before use to a level at which the VOC concentration is less than or equal to the applicable maximum VOC concentration set out in column 3; or
(b)a permit has been issued under section 9, 16 or 19 in respect of the product.
(2)Subject to subsection (4), a person must not manufacture or import a product that belongs to a product category set out in column 1 of Schedule 2 and has a VOC emission potential that is greater than the applicable maximum VOC emission potential set out in column 2, unless a permit has been issued under section 19 in respect of the product.
(3)The exception set out in paragraph (1)(a) does not apply to a multi-purpose solvent or paint thinner referred to in items 48 and 52, respectively, of the table to Schedule 1.
(4)The prohibitions set out in subsections (1) and (2) apply beginning on
(a)in the case of a disinfectant referred to in item 31 of the table to Schedule 1, January 1 of the year following the calendar year of the third anniversary of the day on which these Regulations are registered; or
(b)in any other case, January 1 of the year following the calendar year of the second anniversary of the day on which these Regulations are registered.
4Product belonging to more than one product category#
(2)The maximum VOC concentration for a product that belongs to one of the following product categories is the maximum VOC concentration set out in column 3 of the table to Schedule 1 for the applicable product category set out in column 1 or, if applicable, subcategory set out in column 2, regardless of whether the product also belongs to a product category with a lower maximum VOC concentration:
(a)antiperspirant for the human axilla referred to in item 2 of the table to Schedule 1;
(b)deodorant for the human axilla referred to in item 3 of that table;
(c)hair products referred to in item 6 of that table; or
(d)general-purpose cleaner referred to in item 42 of that table.
5Determination of VOC concentration#
(1)For the purposes of these Regulations and subject to subsections (2) and (3), the VOC concentration of a product that belongs to a product category set out in column 1 of the table to Schedule 1 is determined by the formula
(2)For the purposes of the descriptions WS and WEX, if the product in question belongs to a subcategory set out in column 2 of the table to Schedule 1 that includes aerosol products, the propellant and non-propellant fractions are determined separately then added together to give the total value for each of those elements.
(3)If the product in question is an antiperspirant or deodorant for the human axilla referred to in items 2 and 3, respectively, of the table to Schedule 1, the VOC concentration is determined separately for medium vapour pressure VOCs and high vapour pressure VOCs.
6Determination of VOC emission potential#
When determining the VOC emission potential for the purposes of these Regulations, the following substances are excluded:
(a)low vapour pressure VOCs; and
(b)in the case of charcoal lighter products referred to in item 1 of Schedule 2, fragrances that, combined, constitute 2% or less of the product’s net weight.
VOC Compliance Unit Trading System
Participation
7Purpose of compliance unit trading system#
A person that manufactures or imports a product that belongs to a product category set out in column 1 of the table to Schedule 1 may elect to participate in a compliance unit trading system that allows participants to do one or more of the following:
(a)generate compliance units in accordance with section 11 in respect of all of the reformulated products for which they have elected to participate in the compliance unit trading system;
(b)transfer unused compliance units to another person in accordance with section 12; or
(c)use compliance units that are generated by them or transferred to them to compensate for the excess quantity of VOCs determined in accordance with paragraph 13(d) in respect of a product.
8Permit — participants in compliance unit trading system#
(1)A person that elects to participate in the compliance unit trading system may apply for a permit authorizing them to manufacture or import a product that belongs to a product category set out in column 1 of the table to Schedule 1 and, if applicable, a subcategory set out in column 2 that has a VOC concentration greater than the applicable maximum VOC concentration set out in column 3.
(2)The application must be submitted to the Minister and must contain the following information:
(a)the applicant’s name, civic and postal addresses, telephone number and, if any, fax number and email address;
(b)the name, title, civic and postal addresses, telephone number and, if any, fax number and email address of their authorized representative, if applicable;
(c)for each product in respect of which a permit is sought,
(i)its common or generic name and its trade name, if any,
(ii)the product category set out in column 1 of the table to Schedule 1 and, if applicable, the subcategory set out in column 2 to which it belongs, as well as the information used to categorize it,
(iii)the VOC concentrations at which the applicant expects to manufacture or import the product,
(iv)for each VOC concentration referred to in subparagraph (iii), the quantity of the product, expressed in kilograms, that the applicant expects to manufacture or import per calendar year, excluding any quantity that is manufactured or imported for export only, and
(d)a plan indicating how the applicant intends to compensate for the excess quantity of VOCs determined in accordance with subparagraph (c)(v) for all of the products in respect of which a permit is sought by using compliance units generated by them or transferred to them in accordance with sections 11 and 12.
(3)The Minister may, on receiving the application, require any clarifications that are necessary for the application to be processed.
(4)The applicant must notify the Minister in writing of any change to the information provided under this section — other than that provided under subparagraph (2)(c)(iv) — within 30 days after the day on which the change occurs.
9Issuance#
(1)Subject to subsection (2), the Minister must issue the permit referred to in subsection 8(1) if the applicant has demonstrated how they will compensate for the excess quantity of VOCs determined in accordance with subparagraph 8(2)(c)(v).
(2)The Minister must refuse to issue the permit if
(a)the Minister has reasonable grounds to believe that the applicant has provided false or misleading information in support of their application; or
(b)the information required under subsections 8(2) to (4) and the certification required under section 26 have not been provided or are insufficient to enable the Minister to process the application.
10Revocation — grounds#
(1)The Minister must revoke a permit issued under subsection 9(1) if
(a)the permit holder has not submitted the annual report referred to in section 13 within the prescribed time limit;
(b)the Minister has reasonable grounds to believe that the permit holder has not compensated for the excess quantity of VOCs determined in accordance with paragraph 13(d); or
(c)the Minister has reasonable grounds to believe that the permit holder has provided false or misleading information.
(2)Before revoking a permit, the Minister must provide the permit holder with written reasons and an opportunity to make written representations concerning the revocation.
Generation, Use and Transfer of Compliance Units
11Notice of participation#
(1)A person that intends to generate compliance units in respect of a reformulated product that they manufacture or import must, no later than October 1 of the first year in which they elect to participate in the compliance unit trading system in respect of that product, submit a notice to the Minister that contains the following information:
(a)the person’s name, civic and postal addresses, telephone number and, if any, fax number and email address;
(b)the name, title, civic and postal addresses, telephone number and, if any, fax number and email address of their authorized representative, if applicable; and
(c)respecting the product,
(i)its common or generic name and its trade name, if any,
(ii)the product category set out in column 1 of the table to Schedule 1 and, if applicable, the subcategory set out in column 2 to which it belongs, as well as the information used to categorize it,
(iv)the quantity of the product, expressed in kilograms, that the person expects to manufacture or import during the period beginning on the day on which the notice is submitted and ending on December 31 of the same year, excluding the quantity that is to be manufactured or imported for export only.
(2)A person that has submitted a notice under subsection (1) may generate compliance units, at a rate of one compliance unit per kilogram, for all of the reformulated products that they manufacture or import during a given calendar year. The number of kilograms is determined by the formula
(3)For the first calendar year in which the person participates in the compliance unit trading system, the value of the element Wi in the formula set out in subsection (2) is the quantity of the reformulated product that was manufactured or imported during the period beginning on the day on which the notice referred to in subsection (1) was submitted or the day on which the product was reformulated, whichever is later, and ending on December 31 of that year.
(4)The Minister must provide the person with written confirmation of the number of compliance units that are available to them within 60 days after the day on which the person submits a report in accordance with section 14.
(5)Compliance units whose availability is confirmed by the Minister are valid for two years beginning on January 1 of the year following the calendar year in which they are generated.
12Transfer of compliance units#
(1)A person that participates in the compliance unit trading system may transfer unused compliance units to another person if the compliance units are still valid and the Minister approves the transfer.
(2)The transferee and transferor must, at least 90 days before the day on which the compliance units expire, submit to the Minister a joint application for approval of the transfer, using the form provided by the Minister, that contains the following information:
(a)the names of the transferee and transferor and their civic and postal addresses, telephone numbers and, if any, fax numbers and email addresses;
(b)the number of compliance units to be transferred;
(c)the year during which the compliance units were generated; and
(d)the effective date of the transfer.
(3)The Minister must approve the transfer and inform the transferee and transferor of the approval in writing if the transferor has at least the number of unused compliance units as are proposed to be transferred to the transferee.
(4)The transferee may use the compliance units during the calendar year in which they are transferred and, if there are any compliance units remaining and those compliance units are still valid in accordance with subsection 11(5), during the following calendar year.
(5)For greater certainty, if the transferor does not have at least the number of unused compliance units as are proposed to be transferred to the transferee, the transfer is invalid.
Annual Reports
13Permit issued under subsection 9(1)#
A person that holds a permit issued under subsection 9(1) must, no later than March 1 of each year, submit a report to the Minister that contains the following information in respect of the preceding calendar year:
(a)the person’s name, civic and postal addresses, telephone number and, if any, fax number and email address;
(b)the name, title, civic and postal addresses, telephone number and, if any, fax number and email address of their authorized representative, if applicable;
(c)for each product that the person manufactured or imported under a permit issued under subsection 9(1) during the year in question,
(i)its common or generic name and its trade name, if any,
(ii)the permit number,
(iii)the VOC concentrations at which the product was manufactured or imported, and
(iv)for each VOC concentration referred to in subparagraph (iii), the quantity of the product, expressed in kilograms, that was manufactured or imported during the year in question, excluding the quantity that was manufactured or imported for export only;
(d)for all of the products that the person manufactured or imported under a permit issued under subsection 9(1) during the year in question, the quantity of VOCs in the products that is in excess of the applicable maximum VOC concentration for those products, determined by the formula
(e)the values and data used in the calculation made in accordance with paragraph (d);
(f)the number of compliance units that are being used to compensate for the excess quantity of VOCs determined in accordance with paragraph (d) and
(i)a statement as to whether those compliance units were generated by the person or were transferred to them, and
(ii)if the compliance units were transferred, the date of the transfer and the name of the transferor; and
(g)confirmation of whether the person intends to continue manufacturing or importing products under a permit issued under subsection 9(1) during the calendar year following the year in question and, if so, the quantity of each product, expressed in kilograms, that they expect to manufacture or import during that calendar year, excluding any quantity to be manufactured or imported for export only, and the expected VOC concentration for each product.
14Person that generates compliance units#
A person that generates compliance units during a calendar year must, no later than March 1 of the following year, submit a report to the Minister that contains the following information:
(a)the person’s name, civic and postal addresses, telephone number and, if any, fax number and email address;
(b)the name, title, civic and postal addresses, telephone number and, if any, fax number and email address of their authorized representative, if applicable;
(c)for each reformulated product for which they have elected to participate in the compliance unit trading system for the calendar year in question,
(i)its common or generic name and its trade name, if any,
(ii)the product category set out in column 1 of the table to Schedule 1 and, if applicable, the subcategory set out in column 2 to which it belongs, as well as the information used to categorize it,
(iii)its VOC concentration after reformulation and the date of the reformulation, and
(iv)the quantity of the product, expressed in kilograms, that the person manufactured or imported during the year in question, excluding the quantity that was manufactured or imported for export only;
(d)the values and data used in the calculation made in accordance with subsection 11(2) for the calendar year in question and the result of that calculation; and
(e)confirmation of whether the person intends to continue participating in the compliance unit trading system during the calendar year following the year in question and, if so, the quantity of each product, expressed in kilograms, that they expect to manufacture or import during that calendar year, excluding any quantity to be manufactured or imported for export only, and the expected VOC concentration for each product.
Permit — Products Whose Use Results in Lower VOC Emissions
15Application#
(1)A person may apply for a permit or a renewal of their permit, as the case may be, authorizing them to manufacture or import a product that belongs to a product category set out in column 1 of the table to Schedule 1 and, if applicable, a subcategory set out in column 2 that has a VOC concentration that is greater than the applicable maximum VOC concentration set out in column 3, but that, when used in accordance with the manufacturer’s written instructions, results in lower VOC emissions than those that would result from the use of another product that belongs to the same category and, if applicable, the same subcategory that has a VOC concentration that is less than or equal to that maximum VOC concentration.
(2)The application must be submitted to the Minister and must contain the following information:
(a)the applicant’s name, civic and postal addresses, telephone number and, if any, fax number and email address;
(b)the name, title, civic and postal addresses, telephone number and, if any, fax number and email address of their authorized representative, if applicable;
(c)the product’s common or generic name and trade name, if any;
(d)the product category set out in column 1 of the table to Schedule 1 and, if applicable, the subcategory set out in column 2 to which the product belongs, as well as the information used to categorize it;
(e)the product’s VOC concentration;
(f)the quantity of the product, expressed in kilograms, that the applicant expects to manufacture or import per calendar year, excluding any quantity that is manufactured or imported for export only;
(g)in the case of an application for the renewal of a permit in respect of the product, the number of the existing permit; and
(h)evidence that demonstrates that the use of the product in accordance with the manufacturer’s written instructions results in lower VOC emissions than those that would result from the use of another product that belongs to the same category and, if applicable, the same subcategory that has a VOC concentration that is less than or equal to the applicable maximum VOC concentration set out in column 3 of the table to Schedule 1.
(3)The Minister may, on receiving the application, require any clarifications that are necessary for the application to be processed.
(4)The applicant must notify the Minister in writing of any change to the information provided under this section — other than that provided under paragraph (2)(f) — within 30 days after the day on which the change occurs.
16Issuance or renewal#
(1)Subject to subsection (2), the Minister must issue or renew, as the case may be, a permit referred to in subsection 15(1) if the applicant has demonstrated that, even though the product’s VOC concentration is greater than the applicable maximum VOC concentration set out in column 3 of the table to Schedule 1, the use of the product, in accordance with the manufacturer’s written instructions, results in lower VOC emissions than those that would result from the use of another product that belongs to the same category and, if applicable, the same subcategory that has a VOC concentration that is less than or equal to that maximum VOC concentration.
(2)The Minister must refuse to issue or renew the permit if
(a)the Minister has reasonable grounds to believe that the applicant has provided false or misleading information in support of their application; or
(b)the information required under subsections 15(2) to (4) and the certification required under section 26 have not been provided or are insufficient to enable the Minister to process the application.
(3)The permit expires on the fourth anniversary of the day on which it is issued or renewed unless the permit holder submits an application for renewal at least 90 days before the day on which the permit expires and the application is approved by the Minister.
17Revocation — grounds#
(1)The Minister must revoke a permit issued or renewed under subsection 16(1) in respect of a product if
(a)the Minister has reasonable grounds to believe that the use of the product, in accordance with the manufacturer’s written instructions, no longer results in lower VOC emissions than those that would result from the use of another product that belongs to the same category and, if applicable, the same subcategory that has a VOC concentration that is less than or equal to the applicable maximum VOC concentration set out in column 3 of the table to Schedule 1;
(b)the Minister has reasonable grounds to believe that the permit holder has provided false or misleading information; or
(c)the product does not bear a label, or is not accompanied by documentation, that sets out the instructions referred to in section 23.
(2)Before revoking a permit, the Minister must provide the permit holder with written reasons and an opportunity to make written representations concerning the revocation.
Permit — Technical or Economic Non-feasibility
18Application#
(1)A person that intends to, on or after the applicable date referred to in subsection 3(4) or the day on which their permit expires, as the case may be, manufacture or import a product that belongs to a product category set out in column 1 of the table to Schedule 1 or column 1 of Schedule 2 that has a VOC concentration or VOC emission potential that is greater than the applicable maximum VOC concentration set out in column 3 of the table to Schedule 1 or the applicable maximum VOC emission potential set out in column 2 of Schedule 2, as the case may be, may apply for a permit, or for a renewal of their permit, authorizing them to manufacture or import that product on or after the applicable date if it is not technically or economically feasible for them to, by that date, reduce the product’s VOC concentration or VOC emission potential, as the case may be, to a level that is less than or equal to that maximum VOC concentration or maximum VOC emission potential.
(2)The application must be submitted to the Minister before the applicable date referred to in subsection 3(4) or the day on which the permit expires, as the case may be, and must contain the following information:
(a)the applicant’s name, civic and postal addresses, telephone number and, if any, fax number and email address;
(b)the name, title, civic and postal addresses, telephone number and, if any, fax number and email address of their authorized representative, if applicable;
(c)the product’s common or generic name and trade name, if any;
(d)the product category set out in column 1 of the table to Schedule 1 or column 1 of Schedule 2 and, if applicable, the subcategory set out in column 2 of the table to Schedule 1 to which the product belongs, as well as the information used to determine its classification;
(f)the quantity of the product that the applicant expects to manufacture or import per calendar year, excluding any quantity that is manufactured or imported for export only;
(g)in the case of an application for the renewal of a permit in respect of the product, the number of the existing permit;
(h)the requested validity period for the permit, up to a maximum of two years;
(i)evidence that demonstrates that it will not be technically or economically feasible for the applicant to, by the applicable date referred to in subsection 3(4) or the day on which their permit is to expire, as the case may be, reduce the product’s VOC concentration or VOC emission potential, as the case may be, to a level that is less than or equal to the applicable maximum VOC concentration set out in column 3 of the table to Schedule 1 or the applicable maximum VOC emission potential set out in column 2 of Schedule 2, as the case may be;
(j)a plan describing the measures that will be taken to reduce the product’s VOC concentration or VOC emission potential, as the case may be, to a level that is less than or equal to the applicable maximum VOC concentration set out in column 3 of the table to Schedule 1 or the applicable maximum VOC emission potential set out in column 2 of Schedule 2, as the case may be; and
(k)a statement of the period within which the plan is to be implemented, up to a maximum of two years.
(3)The Minister may, on receiving the application, require any clarifications that are necessary for the application to be processed.
(4)The applicant must notify the Minister in writing of any change to the information provided under this section — other than that provided under paragraph (2)(f) — within 30 days after the day on which the change occurs.
19Issuance or renewal#
(1)Subject to subsection (2), the Minister must issue or renew a permit referred to in subsection 18(1) if the applicant has demonstrated that it will not be technically or economically feasible for them to, by the applicable date referred to in subsection 3(4) or the day on which their permit is to expire, as the case may be, reduce the product’s VOC concentration or VOC emission potential, as the case may be, to a level that is less than or equal to the applicable maximum VOC concentration set out in column 3 of the table to Schedule 1 or the applicable maximum VOC emission potential set out in column 2 of Schedule 2, as the case may be.
(2)The Minister must refuse to issue or renew a permit if
(a)the Minister has reasonable grounds to believe that the applicant has provided false or misleading information in support of their application; or
(b)the information required under subsections 18(2) to (4) and the certification required under section 26 have not been provided or are insufficient to enable the Minister to process the application.
(3)The permit expires on the second anniversary of the day on which the permit becomes effective or on an earlier date specified in the permit unless the permit holder submits an application for renewal at least 90 days before the day on which the permit expires and the application is approved by the Minister. The renewed permit expires on the second anniversary of the day on which the renewal becomes effective or on an earlier date specified in the renewed permit.
(4)An application for renewal may be made only once.
(5)An application for renewal must include an explanation of the reasons why the plan that was submitted in the initial permit application was not implemented within the period identified in that initial application.
20Revocation — grounds#
(1)The Minister must revoke a permit issued or renewed under subsection 19(1) if the Minister has reasonable grounds to believe that the permit holder has provided false or misleading information.
(2)Before revoking a permit, the Minister must provide the permit holder with written reasons and an opportunity to make written representations concerning the revocation.
Accredited Laboratory
21Accredited laboratory#
(1)Any analysis performed to determine the VOC concentration or VOC emission potential of a product for the purposes of these Regulations must be performed by a laboratory that meets the following conditions at the time of the analysis:
(a)it is accredited
(i)under the International Organization for Standardization standard ISO/IEC 17025, entitled General requirements for the competence of testing and calibration laboratories, by an accrediting body that is a signatory to the International Laboratory Accreditation Cooperation Mutual Recognition Arrangement, or
(ii)under the Environment Quality Act, CQLR, c. Q-2; and
(2)If no method has been recognized by a standards development organization in respect of the analysis performed to determine the VOC concentration or VOC emission potential of a product and the scope of the laboratory’s accreditation does not therefore include that analysis, the analysis must be performed in accordance with standards of good scientific practice that are generally accepted at the time that it is performed.
Labelling
22Date of manufacture#
(1)Beginning on the applicable date referred to in subsection 3(4), any person that manufactures or imports a product that belongs to a product category set out in column 1 of the table to Schedule 1 or in column 1 of Schedule 2 must indicate, on the container in which the product is offered for sale or sold, the date on which the product was manufactured or a code representing that date. If a code is used, the person must provide the Minister, on request, with an explanation of the code.
(2)Subsection (1) does not apply to
(a)a personal fragrance product referred to in item 11 of the table to Schedule 1 that is in a container of 2 ml or less; or
(b)any product that belongs to a product category set out in column 1 of that table and has a VOC concentration less than or equal to 0.10% w/w.
23Instructions for use#
Beginning on the applicable date referred to in subsection 3(4), if a product is authorized to be manufactured or imported by a permit issued under subsection 16(1), the manufacturer or importer must ensure that, before the product is offered for sale or sold, it bears a label, or is accompanied by documentation, that sets out instructions in both official languages for the use of the product in a manner that results in lower VOC emissions than those that would result from the use of another product that belongs to the same category and, if applicable, the same subcategory that has a VOC concentration that is less than or equal to the applicable maximum VOC concentration set out in column 3 of the table to Schedule 1.
Record-Keeping
24Records to be maintained#
(1)Beginning on the applicable date referred to in subsection 3(4), any person that manufactures or imports a product that contains VOCs and belongs to a product category set out in column 1 of the table to Schedule 1 or column 1 of Schedule 2 must maintain records containing the following information and any supporting documents:
(a)in the case of a manufacturer,
(i)the product’s common or generic name and trademark and trade name, if any, and
(ii)the quantity of the product that is manufactured at each manufacturing plant and the date of its manufacture; and
(b)in the case of an importer,
(i)the product’s common or generic name and trademark and trade name, if any,
(ii)the quantity of the product that is imported and the date of its importation,
(iii)the name, civic and postal addresses, telephone number and, if any, fax number and email address of the principal place of business of the product’s sender,
(iv)the Harmonized Commodity Description and Coding System number for the product, as set out in the Customs Tariff, and
(v)the business number assigned to the importer by the Minister of National Revenue.
(2)Any person that submits information to the Minister under these Regulations must maintain records containing that information and a copy of any supporting documents.
(3)The records must be kept for a period of at least five years after
(a)the day on which they are made, in the case of the records referred to in subsection (1); and
(b)the day on which the information referred to in subsection (2) is submitted to the Minister, in the case of the records referred to in that subsection.
25Location of records#
(1)The records referred to in section 24 must be kept at the person’s principal place of business in Canada or at any other place in Canada where they can be inspected. If the records are not kept at the person’s principal place of business, the person must provide the Minister with the civic address of the place where they are kept.
(2)If the civic address referred to in subsection (1) changes, the person must notify the Minister in writing within 30 days after the day on which the change occurs.
Submission Requirements
26Certification#
Any information that is submitted under these Regulations must be accompanied by a certification, dated and signed by the person submitting the information or by their authorized representative, stating that the information is accurate and complete.
27Electronic or paper format#
(1)Any document that is submitted under these Regulations may be submitted in paper format or in an electronic format that is compatible with the format that is used by the Minister.
(2)If the document is submitted in electronic format, the document may be signed electronically.
Related Amendment to the Regulations Designating Regulatory Provisions for Purposes of Enforcement (Canadian Environmental Protection Act, 1999)
Coming into Force
Schedule 1 · Product Categories and VOC Concentration Limits (Subsections 1(1) and (4), 2(1) and 3(1) and (3), paragraph 3(4)(a), sections 4, 5 and 7, subsection 8(1), subparagraphs 8(2)(c)(ii) and (v) and 11(1)(c)(ii), subsection 11(2), paragraph 13(d), subparagraph 14(c)(ii), subsection 15(1), paragraphs 15(2)(d) and (h), subsection 16(1), paragraph 17(1)(a), subsection 18(1), paragraphs 18(2)(d), (i) and (j), subsection 19(1), sections 22 and 23 and subsection 24(1))
1Definitions#
The following definitions apply in this Schedule.
cleaner or duster for energized equipment means a product that is designed to clean or dust equipment while there is an electrical current in the equipment or while there is a residual electrical potential from a component such as a capacitor. (nettoyant ou dépoussiéreur d’équipements sous tension)
contact adhesive means non-aerosol adhesive – other than rubber cement that is designed for use on paper substrates and vulcanizing fluid that is designed solely for tire repair — that
(a)is designed for application to surfaces to be bonded together;
(b)is to dry before the surfaces are placed in contact with each other;
(c)forms an immediate bond that makes it difficult or impossible to reposition the adhesive-coated surfaces after they are placed in contact with each other; and
(d)does not require sustained pressure or the clamping of surfaces to establish an adherence between the surfaces after the adhesive-coated surfaces have been brought together using momentary pressure. (adhésif de contact)
Schedule 2 · Product Categories and Maximum VOC Emission Potentials (Subsections 1(4), 2(1) and 3(2), paragraph 6(b), subsection 18(1), paragraphs 18(2)(d), (e), (i) and (j) and subsections 19(1), 22(1) and 24(1))
| Column 1 | Column 2Item | Product Category | Maximum VOC Emission Potential1 | Charcoal lighter products that are incorporated in or designed for use with charcoal to enhance ignition, excluding any product that is(a)an electrical starter or probe;(b)a metallic cylinder that uses paper tinder;(c)natural gas;(d)propane; or(e)wood kindling with naturally occurring levels of sap or resin that enhance ignition of the kindling | 9 g per ignition, when used in accordance with the manufacturer’s instructions2 | Single-use dryer products that are designed to impart softness to, or control the static cling of, fabric | 0.05 g per load, when used in accordance with the manufacturer’s instructions
Federal laws of Canada reproduced under the Reproduction of Federal Law Order (SI/97-5); not the official version. Source: Justice Laws Website.