Contents
THE EUROPEAN COMMISSION,Having regard to the Treaty on the Functioning of the European Union,Having regard to Regulation (EU) No 528/2012 of the European Parliament and of the Council of 22 May 2012 concerning the making available on the market and use of biocidal productsnote, and in particular Article 50(2) thereof,Whereas:
(1)On 22 July 2022, Commission Implementing Regulation (EU) 2022/1423note granted a Union authorisation, under number EU-0024303-0000, to Ecolab Deutschland GmbH for the making available on the market and use of the biocidal product family ‘Hydrogen Peroxide Family 1’. That Regulation was later amended by Commission Implementing Regulation (EU) 2024/2209note, which introduced administrative and minor changes to the authorisation.
(2)Commission Implementing Regulation (EU) No 354/2013note lays down the procedural rules for the different categories of changes referred to in Article 50(3) of Regulation (EU) No 528/2012. Upon receipt of an opinion from the European Chemicals Agency (‘the Agency’) on an application from an authorisation holder of a Union authorisation seeking to change any of the information submitted for the initial application for authorisation, the Commission is to decide whether the conditions of Article 19 or, where relevant, Article 25 of Regulation (EU) No 528/2012, are still met and whether the terms and conditions of the authorisation need to be amended.
(3)On 24 April 2024, Ecolab Deutschland GmbH submitted an application to the Agency, in accordance with Article 12(1) of Implementing Regulation (EU) No 354/2013, for minor changes to the Union authorisation for the biocidal product family ‘Hydrogen Peroxide Family 1’, as referred to in Title 2 of the Annex to that Regulation. Ecolab Deutschland GmbH applied for the following changes, concerning five uses of the products in meta summary of biocidal product characteristics 5: (i) amending the contact time from 30 minutes to 60 minutes for bacterial spores in clean conditions; (ii) amending the contact time from 5 min to 60 min for Clostridium difficile spores in clean conditions; and (iii) removing the claim of 60 minutes for bacterial spores in dirty conditions. The application was recorded in the register for biocidal products under case number BC-AJ094453-41.
(4)On 20 September 2024, the Agency submitted to the Commission an opinion of the Biocidal Products Committeenote on the application for minor changes, in accordance with Article 12(4) of Implementing Regulation (EU) No 354/2013, together with a revised summary of the biocidal product characteristics and a revised assessment report. In the opinion, the Agency concludes that after the implementation of the changes sought by the authorisation holder, the conditions of Article 19 of Regulation (EU) No 528/2012 are still met.
(5)On 11 October 2024, the Agency transmitted to the Commission the revised summary of biocidal product characteristics of the Union authorisation for the biocidal product family ‘Hydrogen Peroxide Family 1’ in all official languages of the Union covering the minor changes applied for, in accordance with Article 12(6) of Implementing Regulation (EU) No 354/2013.
(6)The Commission concurs with the opinion of the Agency and therefore considers it appropriate to amend the Union authorisation for the biocidal product family ‘Hydrogen Peroxide Family 1’ to introduce the minor changes requested by Ecolab Deutschland GmbH.
(7)Except for the amendments regarding the minor changes, all other information included in the summary of the biocidal product characteristics of ‘Hydrogen Peroxide Family 1’ as set out in the Annex to Implementing Regulation (EU) 2022/1423 remains unchanged.
(8)In order to enhance clarity and to ease the access of users and interested parties to the final consolidated version of the summary of biocidal product characteristics which is to be published by the Agency, the Annex to Implementing Regulation (EU) 2022/1423 should be replaced in its entirety. Due to a change in the format used for the generation of the summary of biocidal product characteristics in the register for biocidal products in February 2024, the summary of biocidal product characteristics in that Annex should also include some minor editorial and layout changes.
(9)Implementing Regulation (EU) 2022/1423 should therefore be amended accordingly,
HAS ADOPTED THIS REGULATION:
Article 1#
The Annex to Implementing Regulation (EU) 2022/1423 is replaced by the text set out in the Annex to this Regulation.
Article 2#
This Regulation shall enter into force on the twentieth day following that of its publication in the Official Journal of the European Union.
Summary of product characteristics for a biocidal product family
Hydrogen Peroxide Family 1
Product type(s)
PT02: Disinfectants and algaecides not intended for direct application to humans or animals
PT04: Food and feed area
PT03: Veterinary hygiene
PT01: Human hygiene
Authorisation number EU-0024303-0000
R4BP asset number EU-0024303-0000
Part I — first information level
1. Administrative information
1.1. Family name
| Name | Hydrogen Peroxide Family 1 |
1.2. Product type(s)
| Product type(s) | PT02: Disinfectants and algaecides not intended for direct application to humans or animalsPT04: Food and feed areaPT03: Veterinary hygienePT01: Human hygiene |
1.3. Authorisation holder
| Name and address of the authorisation holder | Name | Ecolab Deutschland GmbH |
| Address | Ecolab Allee 1 40789 Monheim am Rhein DE | |
| Authorisation number | EU-0024303-0000 | |
| R4BP asset number | EU-0024303-0000 | |
| Date of the authorisation | 15 September 2022 | |
| Expiry date of the authorisation | 31 October 2032 |
1.4. Manufacturer(s) of the product
| Name of manufacturer | Ecolab Europe GmbH |
| Address of manufacturer | Richtistrasse 7 8304 Walliselen Switzerland |
| Location of manufacturing sites | Ecolab Europe GmbH site 1A.F.P. GmbH Otto-Brenner-Straße 16 21337 Lüneburg GermanyEcolab Europe GmbH site 2ACIDEKA S.A. Edificio Feria. Capuchinos de Basurto 6, 4a planta 48013 Bilbao. Bizkaia SpainEcolab Europe GmbH site 3ADIEGO HNOS CTRA DE VALENCIA, KM 5,900 50410 CUARTE DE HUERVA (ZARAGOZA) 50410 Zaragoza SpainEcolab Europe GmbH site 4ALLIED PRODUCTS Allied Hygiene Unit 11, Belvedere Industrial Estate Fishers Way DA17 6BS Belvedere, Kent United Kingdom of Great Britain and Northern Ireland (the)Ecolab Europe GmbH site 5Arkema GmbH Morschheimer Srtrasse 19 D-67292 Krichheimbolanden GermanyEcolab Europe GmbH site 6AZELIS DENMARK Lundtoftegårdsvej 95 2800 Kgs. 2800 Kgs Lyngby DenmarkEcolab Europe GmbH site 7Belinka Zasavska Cesta 95 1001 Ljubljana SloveniaEcolab Europe GmbH site 8BENTUS LABORATORIES LTD. RUSSIA, 105005, MOSCOW, RADIO STREET, 24 BLD.1 105005 Moscow Russian Federation (the)Ecolab Europe GmbH site 9BIO PRODUCTIONS 72 VICTORIA ROAD, VICTORIA INDUSTRIAL ESTATE, BURGESS HILL, WEST SUSSEX RH159LH Burgess Hill United Kingdom of Great Britain and Northern Ireland (the)Ecolab Europe GmbH site 10BIOXAL SA Route des Varennes - Secteur A – BP 30072 71103 Chalon sur Saône Cedex FranceEcolab Europe GmbH site 11Bores Srl Via Pioppa, 179 44020 Pontegradella ItalyEcolab Europe GmbH site 12BRENNTAG ARDENNES Route de Tournes CD n 2 FR-08090 FR-08090 Cliron FranceEcolab Europe GmbH site 13BRENNTAG CEE - GUNTRAMSDORF Brenntag CEE GmbH Mixing / Blending Bahnstr. 13 A-2353 Guntramsdorf AustriaEcolab Europe GmbH site 14BRENNTAG Duisburg/Glauchau/Hamburg/Heilbronn Brenntag GmbH Humboldtring 15 45472 Muehlheim GermanyEcolab Europe GmbH site 15BRENNTAG Kaiserslautern Brenntag Merkurstr. 47 67663 Kaiserslautern GermanyEcolab Europe GmbH site 16BRENNTAG Kleinkarlbach/Lohfelden Brenntag GmbH Humboldtring 15 45472 Muehlheim GermanyEcolab Europe GmbH site 17BRENNTAG Nordic - HASLEV Høsten Teglværksvej 47 4690 Haslev DenmarkEcolab Europe GmbH site 18Brenntag Nordic, Strandgade 35 7100 Vejle DenmarkEcolab Europe GmbH site 19BRENNTAG Normandy Brenntag Normandie 12 Sente des Jumelles - BP 11 76710 76710 Montville FranceEcolab Europe GmbH site 20BRENNTAG PL -Zgierz ul. Kwasowa 5 95-100 Zgierz PolandEcolab Europe GmbH site 21Brenntag Quimica S.A. - Madrid. Calle Gutemberg no 22,.Poligono Industrial El Lomo 28906 Madrid SpainEcolab Europe GmbH site 22BRENNTAG Schweizerhall Brenntag Schweizerhall AG Elsaesserstr. 231 CH-4056 Basel SwitzerlandEcolab Europe GmbH site 23Budich International GmbH Dieselstrasse 10 32120 Hiddenhause GermanyEcolab Europe GmbH site 24Caldic Deutschland Chemie B.V Caldic Deutschland GmbH & Co.Kg Am Karlshof 10 D 40231 Duesseldorf GermanyEcolab Europe GmbH site 25Carbon Chemicals Group Ltd, Ringaskiddy P43 R772 County Cork IrelandEcolab Europe GmbH site 26COLEP BAD SCHMIEDEBERG ColepCCL Bad Schmiedeberg GmbH Kemberger Str. 3 06905 Bad Schmiedeberg GermanyEcolab Europe GmbH site 27COMERCIAL FARMACEUTICA CASTEL: LANA, S.A. “COFARCAS” Condado de Treviño, 46 P.I. Villalonquejar 09080 – BURGOS 09080 Burgos SpainEcolab Europe GmbH site 28COMERCIAL GODO França, 13 08700 – IGUALADA (BARCELONA) 08700 BARCELONA SpainEcolab Europe GmbH site 29COURTOIS SARL ZA SOUS LE BEER Route de Pacy 27730 BUEIL FranceEcolab Europe GmbH site 30DAN MOR (DR WIPE) DAN-MOR Natural Products and Chemicals Ltd. Or Akiva Industrial Zone 30600 Akiva Industrial Zone IsraelEcolab Europe GmbH site 31Denteck BV Heliumstraat 8 2718 SL ZOETERMEER Netherlands (the)Ecolab Europe GmbH site 32DETERGENTS BURGUERA DETERGENTS BURGUERA, S.L. Joan Ballester 50 07630 CAMPOS (ILLES BALEARES) SpainEcolab Europe GmbH site 33ECL Biebesheim NLC Biebesheim Justus-von-Liebig-Straße 11 64584 Biebesheim am Rhein GermanyEcolab Europe GmbH site 34ECL Celra NALCO - Celra C/ Tramuntana s/n Poligona Industrial Celra 17460 Girona SpainEcolab Europe GmbH site 35ECL Châlons AVENUE DU GENERAL PATTON 51000 CHALONS EN CHAMPAGNE FranceEcolab Europe GmbH site 36ECL Cisterna Nalco Italiana Manufacturing Srl.Via Ninfina II 04012 Cisterna di Latina ItalyEcolab Europe GmbH site 37ECL Fawley NLC Fawley Cadland Road, Hythe, SO45 3NP Southampton, Hampshire United Kingdom of Great Britain and Northern Ireland (the)Ecolab Europe GmbH site 38ECL Leeds ECOLAB Lotherton Way Garforth Leeds LS25 2JY LS25 2JY Leeds United Kingdom of Great Britain and Northern Ireland (the)Ecolab Europe GmbH site 39ECL Mandra 25TH KM OLD NATIONAL ROAD OF ATHENS TO THIVA, GR 19600 GR 19600 ATHENS GreeceEcolab Europe GmbH site 40ECL Maribor Vajngerlova 4, SI-2001 Maribor SI-2001 Maribor SloveniaEcolab Europe GmbH site 41ECL MICROTEK BV MICROTEK MEDICAL B.V. GESINKKAMPSTRAAT 19, 7051 HR, VARSSEVELD 7051 HR VARSSEVELD Netherlands (the)Ecolab Europe GmbH site 42ECL MICROTEK MOSTA SORBONNE CENTRE, F20 MOSTA TECHNOPARK, MOSTA MST 3000 MOSTA MaltaEcolab Europe GmbH site 43ECL Nieuwegein BRUGWAL 11 A, 3432 NZ NIEUWEGEIN 3432 NZ NIEUWEGEIN Netherlands (the)Ecolab Europe GmbH site 44ECL Rovigo Esoform Esoform S.p.A. Laboratorio Chimico Farmaceutico Viale del Lavoro 10 45100 Rovigo ItalyEcolab Europe GmbH site 45ECL Rozzano Via A. Grandi, 20089 Rozzano MI 20089 Rozzano ItalyEcolab Europe GmbH site 46ECL Tesjoki NLC Tesjoki Kivikummuntie 1, Tesjoki 07955 Tesjoki FinlandEcolab Europe GmbH site 47ECL Tessenderlo INDUSTRIEZONE RAVENSHOUT 4 3980 Tessenderlo BelgiumEcolab Europe GmbH site 48Ecolab Ltd Baglan/Swindon, Plot 7a Baglan Energy Park, Baglan, Port Talbot SA11 2HZ Port Talbot United Kingdom of Great Britain and Northern Ireland (the)Ecolab Europe GmbH site 49EXTRUPLAST ZI Fief du Passage 56 rue Robert Geffré 17000 La Rochelle FranceEcolab Europe GmbH site 50Ferdinand Eimermacher GmbH & Co. KG Westring 24 48356 Nordwalde GermanyEcolab Europe GmbH site 51F.E.L.T. BP 64 10 rue du Vertuquet 59531 NEUVILLE EN FERRAIN FranceEcolab Europe GmbH site 52Gallows Green Services Ltd. Cod Beck Mill Industrial Estate Dalton Lane YO7 3HR Thirsk North Yorkshire United Kingdom of Great Britain and Northern Ireland (the)Ecolab Europe GmbH site 53GERDISA GERMAN RGUEZ DROGAS IND Gerdisa Polígono Industrial Miralcampo parc.37 19200 Azuqueca de Henares Guadalajara SpainEcolab Europe GmbH site 54GIRASOL NATURAL PRODUCTS BV De Veldoven 12-14 3342 GR Hendrik-Ido-Ambacht 3342 GR Hendrik-Ido-Ambacht Netherlands (the)Ecolab Europe GmbH site 55HENKEL ENGELS Henkel Engels 413116 Engels Prospekt StroiTel ei Russia 413116 Engels Russian Federation (the)Ecolab Europe GmbH site 56Imeco GmbH & Co. KG Boschstraße 5 D-63768 Hösbach GermanyEcolab Europe GmbH site 57INTERFILL LLC-TOSNO INTERFILL LLC 187000, Moskovskoye shosse 1 187000 Tosno - Leningradskaya Russian Federation (the)Ecolab Europe GmbH site 58JODEL - PRODUCTOS QUIMICOS Jodel Zona Industrial 2050 Aveiras de Cima 2050 Aveiras de Cima PortugalEcolab Europe GmbH site 59Kleinmann GmbH Am Trieb 13 72820 Sonnenbühl GermanyEcolab Europe GmbH site 60Kompak Nederland B.V. Ambachtsweg 4, 4854 MK, Bavel Netherlands (the)Ecolab Europe GmbH site 61La Antigua Lavandera SL LA ANTIGUA LAVANDERA, S.L. Ctra. Antigua Sevilla-Alcalá Km.1,5 (SE-410) Apartado de Correos, 58 41500 Sevilla SpainEcolab Europe GmbH site 62LABORATOIRES ANIOS Pavé du moulin 59260 Lille-Hellemmes FranceEcolab Europe GmbH site 63LABORATOIRES ANIOS 3330 Rue de Lille 59262 Sainghin-en-Mélantois FranceEcolab Europe GmbH site 64LICHTENHELDT GmbH Lichtenheldt Industriestrasse 7-9 23812 Wahlstedt GermanyEcolab Europe GmbH site 65Lonza GmbH Morianstr.32 42103 Wuppertal GermanyEcolab Europe GmbH site 66McBride SA Polígon Industrial L’Illa C / Ramon Esteve, 20- 22 08650 Sallent SpainEcolab Europe GmbH site 67Multifill BV Constructieweg 25-A 3641 SB Mijdrecht 3641 Mijdrecht Netherlands (the)Ecolab Europe GmbH site 68NOPA NORDISK PARFUMERIVARE Nordisk Parfumerivarefabrik A/S Hvedevej 2-22 DK-8900 Randers DenmarkEcolab Europe GmbH site 69PAL INTERNATIONAL LTD Pal International Ltd. Sandhurst Street, Oadby Leicester Leicester United Kingdom of Great Britain and Northern Ireland (the)Ecolab Europe GmbH site 70Planol GmbH Maybachstr. 17 63456 Hanau GermanyEcolab Europe GmbH site 71Plum A/S Frederik Plums Vej 2 DK 5610 Assens DenmarkEcolab Europe GmbH site 72PRODUCTOS LC LA CORBERANA, S.L. Crta. Corbera – Polinyá 46612 Valencia SpainEcolab Europe GmbH site 73THE PROTON GROUP LTD Ripley Drive, Normanton Industrial Estate WF6 1QT Wakefield United Kingdom of Great Britain and Northern Ireland (the)Ecolab Europe GmbH site 74QUIMICAS MORALES, S.L. Misiones, 11 - Urb. El Sebadal 05005 LAS PALMAS DE GRAN CANARIA SpainEcolab Europe GmbH site 75RNM PRODUCTOS QUIMICOS RNM - Produtos Quimicos, Lda Rua da Fabrica, 123 4765-080 Segade PortugalEcolab Europe GmbH site 76ROQUETTE & BARENTZ Roquette Freres Route De La Gorgue F-62136 Lestrem FranceEcolab Europe GmbH site 77RUTPEN LTD MEMBURY AIRFIELD RG16 7TJ LAMBOURN United Kingdom of Great Britain and Northern Ireland (the)Ecolab Europe GmbH site 78SOLIMIX Solimix Montseny 17-19 Pol. Ind. Sant Pere Molanta 08799 Barcelona SpainEcolab Europe GmbH site 79Staub & Co. – Silbermann GmbH , Industriestraße 3 D-86456 Gablingen GermanyEcolab Europe GmbH site 80Stockmeier Chemie Eilenburg GmbH & Co. KG Gustav-Adolf-Ring 5 04838 Eilenburg GermanyEcolab Europe GmbH site 81SYNERLOGIC BV ( - IN2FOOD) Synerlogic BV afd. L.J. Costerstraat 5 6827 ARNHEM Netherlands (the)Ecolab Europe GmbH site 82Univar Ltd, Argyle House, Epsom Avenue SK9 3RN Wilmslow United Kingdom of Great Britain and Northern Ireland (the)Ecolab Europe GmbH site 83Univar SPA Via Caldera 21 20-153 Milano Milano ItalyEcolab Europe GmbH site 84van Dam Bodegraven B.V Postbus 48 NL 2410 AA Bodegraven Netherlands (the)Ecolab Europe GmbH site 85Laboratoires Prodene Klint Rue Denis Papin, 2 Z.I. Mitry Compans F-77290 Mitry Mory F-77290 Mitry Mory FranceEcolab Europe GmbH site 86Simagec Z.I. de Rousset / Peynier, 54 Avenue de la Plaine 13790 Rousset FranceEcolab Europe GmbH site 87INNOVATE GmbH, Innovate GmbH Am Hohen Stein 11 06618 Naumburg GermanyEcolab Europe GmbH site 88Sima Pharma, 54 Avenue de la Plaine, ZI 13106 Rousset Cedex FranceEcolab Europe GmbH site 89Techtex (Technical Textile Services Ltd) Units 7 & 8, Rhodes Business Park, Silburn Way, Middleton, M24 4NE Manchester United Kingdom of Great Britain and Northern Ireland (the)Ecolab Europe GmbH site 90Helico B.V. Hoogschaijksestraat 31 5374 EC Schaijk Netherlands (the)Ecolab Europe GmbH site 91INCARE BV Keizersveld 99 5803 AP Venray Netherlands (the)Ecolab Europe GmbH site 92ECL Mullingar Ecolab Ltd (IE). Forrest Park Zone C Mullingar Industrial Estate Mullingar Co. Westmeath Westmeath IrelandEcolab Europe GmbH site 93ECL Mullingar. Ecolab Manufacturing IE Ltd (IE) Forest Park, Zone C Mullingar Ind. Estate N91 Mullingar, Co. Westmeath Westmeath IrelandEcolab Europe GmbH site 94ECL Weavergate Site: Nalco Manufacturing Limited, Winnington Avenue, CW8 3AA Northwich, Cheshire (Postal Address: PO Box 11, Winnington Avenue, Northwich, Cheshire CW8 4DX) United Kingdom of Great Britain and Northern IrelandEcolab Europe GmbH site 95ECL Weavergate, Ecolab Ltd (UK) Winnington Avenue CW8 3AA Northwich, Cheshire United Kingdom of Great Britain and Northern IrelandEcolab Europe GmbH site 96ECL Weavergate, Ecolab Manufacturing UK Ltd (UK) Winnington Avenue CW8 3AA Northwich, Cheshire United Kingdom of Great Britain and Northern Ireland |
1.5. Manufacturer(s) of the active substance(s)
| Active substance | Hydrogen peroxide |
| Name of manufacturer | Evonik Degussa Antwerpen NV |
| Address of manufacturer | Tijsmanstunnel West 2040 Antwerpen Belgium |
| Location of manufacturing sites | Evonik Degussa Antwerpen NV site 1Tijsmanstunnel West 2040 Antwerpen Belgium |
| Active substance | Hydrogen peroxide |
| Name of manufacturer | Evonik Degussa GmbH |
| Address of manufacturer | Untere Kanalstr. 3 79618 Rheinfelden Germany |
| Location of manufacturing sites | Evonik Degussa GmbH site 1Untere Kanalstr. 3 79618 Rheinfelden Germany |
| Active substance | Hydrogen peroxide |
| Name of manufacturer | Evonik Peroxid GmbH |
| Address of manufacturer | Industriestraβe 1 9721 Weiβenstein Austria |
| Location of manufacturing sites | Evonik Peroxid GmbH site 1Industriestraβe 1 9721 Weiβenstein Austria |
| Active substance | Hydrogen peroxide |
| Name of manufacturer | Evonik Peroxide Netherlands BV |
| Address of manufacturer | Oosterhorn 14 9936 HD Farmsum Netherlands (the) |
| Location of manufacturing sites | Evonik Peroxide Netherlands BV site 1Oosterhorn 14 9936 HD Farmsum Netherlands (the) |
| Active substance | Hydrogen peroxide |
| Name of manufacturer | Belinka Perkemija D.O.O |
| Address of manufacturer | Zasavska cesta 95 1231 Ljubljana-Črnuče Slovenia |
| Location of manufacturing sites | Belinka Perkemija D.O.O site 1Zasavska cesta 95 1231 Ljubljana-Črnuče Slovenia |
| Active substance | Hydrogen peroxide |
| Name of manufacturer | Solvay Chemie SA |
| Address of manufacturer | Rue Solvay 39 B-5190 Jemeppe-sur-Sambre Belgium |
| Location of manufacturing sites | Solvay Chemie SA site 1Rue Solvay 39 B-5190 Jemeppe-sur-Sambre Belgium |
| Active substance | Hydrogen peroxide |
| Name of manufacturer | Solvay Chimica Italia S.p.A |
| Address of manufacturer | Via Piave 6 I-57013 Rosignano Solvay LI Italy |
| Location of manufacturing sites | Solvay Chimica Italia S.p.A site 1Via Piave 6 I-57013 Rosignano Solvay LI Italy |
| Active substance | Hydrogen peroxide |
| Name of manufacturer | Solvay Chemicals GmbH |
| Address of manufacturer | Köthensche Strasse 1-3 D-06406 Bernburg Germany |
| Location of manufacturing sites | Solvay Chemicals GmbH site 1Köthensche Strasse 1-3 D-06406 Bernburg Germany |
| Active substance | Hydrogen peroxide |
| Name of manufacturer | Solvay Interox Limited |
| Address of manufacturer | Baronet Road WA4 6HB Warrington Cheshire United Kingdom of Great Britain and Northern Ireland (the) |
| Location of manufacturing sites | Solvay Interox Limited site 1Baronet Road WA4 6HB Warrington Cheshire United Kingdom of Great Britain and Northern Ireland (the) |
| Active substance | Hydrogen peroxide |
| Name of manufacturer | Solvay Chemicals Finland OY |
| Address of manufacturer | Yrjonojantie 2 45910 Voikkaa Finland |
| Location of manufacturing sites | Solvay Chemicals Finland OY site 1Yrjonojantie 2 45910 Voikkaa Finland |
| Active substance | Hydrogen peroxide |
| Name of manufacturer | Solvay Interox Produtos Peroxidados SA |
| Address of manufacturer | Rua Eng. Clement Dumoulin P-2625-106 Povoa de Santa Iria Portugal |
| Location of manufacturing sites | Solvay Interox Produtos Peroxidados SA site 1Rua Eng. Clement Dumoulin P-2625-106 Povoa de Santa Iria Portugal |
| Active substance | Hydrogen peroxide |
| Name of manufacturer | Kemira Rotterdam BV |
| Address of manufacturer | Moezelweg 151 3198 LS Europoort Rotterdam Netherlands (the) |
| Location of manufacturing sites | Kemira Rotterdam BV site 1Moezelweg 151 3198 LS Europoort Rotterdam Netherlands (the) |
| Active substance | Hydrogen peroxide |
| Name of manufacturer | Kemira Chemical Oy |
| Address of manufacturer | Typpitie PL 171 90101 Oulu Finland |
| Location of manufacturing sites | Kemira Chemical Oy site 1Typpitie PL 171 90101 Oulu Finland |
| Active substance | Hydrogen peroxide |
| Name of manufacturer | Kemira Kemi AB |
| Address of manufacturer | Industrigatan 83 25109 Helsingborg Sweden |
| Location of manufacturing sites | Kemira Kemi AB site 1Industrigatan 83 25109 Helsingborg Sweden |
| Active substance | Hydrogen peroxide |
| Name of manufacturer | ARKEMA France – USINE DE JARRIE |
| Address of manufacturer | Route National 85, BP 1 38560 JARRIE France |
| Location of manufacturing sites | ARKEMA France – USINE DE JARRIE site 1Route National 85, BP 1 38560 JARRIE France |
| Active substance | Hydrogen peroxide |
| Name of manufacturer | ARKEMA GMBH – NIEDERLASSUNG LEUNA |
| Address of manufacturer | Am Haupttor, Bau 2410 06237 LEUNA Germany |
| Location of manufacturing sites | ARKEMA GMBH – NIEDERLASSUNG LEUNA site 1Am Haupttor, Bau 2410 06237 LEUNA Germany |
| Active substance | Hydrogen peroxide |
| Name of manufacturer | Ecolab Europe GmbH |
| Address of manufacturer | Ecolab-Allee 1 40789 Monheim am Rhein Germany |
| Location of manufacturing sites | Ecolab Europe GmbH site 1Ecolab-Allee 1 40789 Monheim am Rhein Germany |
2. Product family composition and formulation
2.1. Qualitative and quantitative information on the composition of the family
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
|---|---|---|---|---|---|
| Hydrogen peroxide | active substance | 7722-84-1 | 231-765-0 | 1 - 36,75 % (w/w) | |
| N-propanol | Propan-1-ol | Non-Active substance | 71-23-8 | 200-746-9 | 0 - 17,5 % (w/w) |
| Citric acid monohydrate | 2-hydroxypropane -1,2,3-tricarboxylic acid | Non-Active substance | 5949-29-1 | 201-069-1 | 0 - 0,9 % (w/w) |
| Phenoxyethanol | 2-Phenoxyethanol | Non-Active substance | 122-99-6 | 204-589-7 | 0 - 0,9 % (w/w) |
| Sodium lauryl Sulphate | Sodium dodecyl sulphate | Non-Active substance | 151-21-3 | 205-788-1 | 0 - 3,88 % (w/w) |
| L-Glutamic acid, N-coco acyl derivs., monosodium salts | Sodium;(4S)-4-amino-5-hydroxy-5-oxopentanoate | Non-Active substance | 68187-32-6 | 269-087-2 | 0 - 2 % (w/w) |
| Sulfuric acid, mono-C12-14-alkyl esters, ammonium salts (Texapon ALS) | Sulfuric acid, mono-C12-14-alkyl esters, ammonium salts | Non-Active substance | 90583-11-2 | 292-209-0 | 0 - 1,12 % (w/w) |
| Phosphoric acid | Orthophosphoric acid | Non-Active substance | 7664-38-2 | 231-633-2 | 0 - 1,5 % (w/w) |
| Nitric acid | Nitric acid | Non-Active substance | 7697-37-2 | 231-714-2 | 0 - 3,71 % (w/w) |
| Alcohol EO phosphate ester | Poly(oxy-1,2-ethanediyl), .alpha.-hydro-.omega.-hydroxy-, mono-C8-10-alkyl ethers, phosphates | Non-Active substance | 68130-47-2 | 0 - 14,625 % (w/w) | |
| Alkylpolyglycoside C8-C10 | (3R,4S,5S,6R)-2-decoxy-6-(hydroxymethyl)oxane-3,4,5-triol | Non-Active substance | 68515-73-1 | 500-220-1 | 0 - 6,35 % (w/w) |
| Alcohols, C10-C16 ethoxylated propoxylated (Dehydol 980) | Alcohols, C10-C16 ethoxylated propoxylated | Non-Active substance | 69227-22-1 | 0 - 3 % (w/w) | |
| Capryleth-9 Carboxylic acid (mixture of alkyl ether carboxylic acid) | Poly(oxy-1,2-ethanediyl), .alpha.-(carboxymethyl)-.omega.-(octyloxy)- (4-11 EO) | Non-Active substance | 53563-70-5 | 0 - 2,15 % (w/w) | |
| Hexeth-4 Carboxylic Acid (mixture of alkyl ether carboxylic acid) | Poly(oxy-1,2-ethanediyl), .alpha.-(carboxymethyl)-.omega.-(hexyloxy)- (3 EO) | Non-Active substance | 105391-15-9 | 0 - 0,62 % (w/w) |
2.2. Type(s) of formulation
| Formulation type(s) | AL Any other liquidGW Water soluble gelSL Soluble concentrate |
Part II. — second information level - meta spc(s)
1. Meta spc 1 administrative information
1.1. Meta SPC 1 identifier
| Identifier | Meta SPC: META SPC 1 |
1.2. Suffix to the authorisation number
| Number | 1-1 |
1.3. Product type(s)
| Product type(s) | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
2. Meta spc 1 composition
2.1. Qualitative and quantitative information on the composition of the meta SPC 1
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
|---|---|---|---|---|---|
| Hydrogen peroxide | active substance | 7722-84-1 | 231-765-0 | 6 - 6,6 % (w/w) |
2.2. Type(s) of formulation of the meta SPC 1
| Formulation type(s) | AL Any other liquid |
3. Hazard and precautionary statements of the meta spc 1
| Hazard statements | H319: Causes serious eye irritation. |
| Precautionary statements | P264: Wash hands thoroughly after handling.P280: Wear eye protection.P280: Wear face protection.P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.P337+P313: If eye irritation persists: Get medical advice.P337+P313: If eye irritation persists: Get medical attention. |
4. Authorised use(s) of the meta spc
4.1. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: No dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: VirusesCommon name: VirusesDevelopment stage: no dataScientific name: Bacterial sporesCommon name: Bacterial sporesDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Spraying using trigger sprayer and dry wipeDetailed description:Disinfection of small surfaces, materials and equipment in life sciences cleanrooms, classified as grade A to D according to Good Manufacturing Practice (GMP) EU classification, and supporting environments. Contact times for spraying at 20oC in clean conditions:15 minutes for bacteria and fungi;5 minutes for yeasts;60 minutes for viruses and bacterial spores.Contact times for spraying and wiping at 20oC in clean conditions:5 minutes for bacteria, yeasts and fungi;60 minutes for viruses and bacterial spores. |
| Application rate(s) and frequency | Application rate:Application rate: 10 ml/m2Dilution (%):Ready to use (RTU) productNumber and timing of application:Application frequency: up to twice per day per room |
| Category(ies) of users | professional |
| Pack sizes and packaging material | Light precluding High Density Poly Ethylene (HDPE) or Poly Ethylene (PE) Bottle, 1-5 LLight precluding Polypropylene and Polyethylene (PP+PE) spray bottle, 0.5 -5 L |
4.1.1. Use-specific instructions
For optimum results, hold the bottle upright and spray from a distance of 10 cm to 20 cm. Spray the product onto a dry wipe and wipe small surfaces such as worktops and equipment, or spray the product onto the surface, wipe the surface with a clean, dry wipe and let air dry. Always close the nozzle after use. Used wipes must be disposed of in a closed container.
4.1.2. Use-specific risk mitigation measures
The use of eye protection while handling the product is mandatory.
4.1.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 1.
4.1.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 1.
4.1.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 1.
4.2. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: VirusesCommon name: VirusesDevelopment stage: no dataScientific name: Bacterial sporesCommon name: Bacterial sporesDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Mopping using a flat mop and bucketDetailed description:Disinfection of floors in life sciences cleanrooms, classified as grade A to D according to Good Manufacturing Practice (GMP) EU classification, and supporting environments. Contact times for mopping at 20oC in clean conditions:5 minutes for bacteria, yeasts and fungi;60 minutes for viruses and bacterial spores. |
| Application rate(s) and frequency | Application rate:Application rate: 20 ml/m2Dilution (%):RTU productNumber and timing of application:Application frequency: up to twice per day per room |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Light precluding HDPE or PE Bottle, 0.5 -5 L |
4.2.1. Use-specific instructions
Apply to surfaces by mopping and let air dry.
4.2.2. Use-specific risk mitigation measures
The use of eye protection while handling the product is mandatory.
Use of respiratory protective equipment (RPE) providing a protection factor of 10 is mandatory for professionals applying the product and for other professionals present in the treated area. An air purifying respirator with helmet/hood/mask (TH1/TM1), or a half/full mask with combination filter gas/P2 is at least required (filter type (code letter, colour) to be specified by the authorisation holder within the product information). For repeated application or re-entry into the room, the professional needs to follow the same risk mitigation measures as for the first application in the room.
4.2.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 1.
4.2.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 1.
4.2.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 1.
4.3. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: VirusesCommon name: VirusesDevelopment stage: no dataScientific name: Bacterial sporesCommon name: Bacterial sporesDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Wiping using impregnated RTU wipesDetailed description:Disinfection of small surfaces, materials and equipment in life sciences cleanrooms, classified as grade A to D according to Good Manufacturing Practice (GMP) EU classification, and supporting environments. Contact times for wiping at 20oC in clean conditions:5 minutes for bacteria, yeasts and fungi;60 minutes for viruses and bacterial spores. |
| Application rate(s) and frequency | Application rate:Application rate: 1 wipe per m2 (corresponds to 10 ml/m2)Dilution (%):RTU productNumber and timing of application:Application frequency: up to twice per day per room |
| Category(ies) of users | professional |
| Pack sizes and packaging material | Light precluding PP or PET/PE or EVA/PP or Aluminum/PE Pouch or PE Pouch with 10-100 impregnated 45% polyester / 55% cellulose blend wipes (wipe size: 200x200 mm)Light precluding PP or PET/PE or EVA/PP or Aluminum/PE Pouch or PE Pouch with 10-100 impregnated 100% polyester wipes (wipe size: 200x200 mm).Light precluding PP or PET/PE or EVA/PP or Aluminum/PE Pouch or PE Pouch with 10-100 impregnated 100% polyester wipes (wipe size: 300x300 mm) |
4.3.1. Use-specific instructions
Allow surface to air dry after using the product. Close container when not in use. Do not use wipes which have become dehydrated. Used wipes must be disposed of in a closed container.
4.3.2. Use-specific risk mitigation measures
Avoid hand to eye transfer.
4.3.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 1.
4.3.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 1.
4.3.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 1.
4.4. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: VirusesCommon name: VirusesDevelopment stage: no dataScientific name: Bacterial sporesCommon name: Bacterial sporesDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Mopping using impregnated RTU mop wipesDetailed description:Disinfection of floors in life sciences cleanrooms, classified as grade A to D according to Good Manufacturing Practice (GMP) EU classification, and supporting environments. Contact times for mopping at 20oC in clean conditions:5 minutes for bacteria, yeasts and fungi;60 minutes for viruses and bacterial spores. |
| Application rate(s) and frequency | Application rate:Application rate: 1 wipe per m2 (corresponds to 10 ml/m2)Dilution (%):RTU productNumber and timing of application:Application frequency: up to twice per day per room |
| Category(ies) of users | professional |
| Pack sizes and packaging material | Light precluding PP or PET/PE or EVA/PP or Aluminum/PE Pouch or PE Pouch with 10-100 impregnated 45% polyester / 55% cellulose blend wipes (wipe size: 420x250 mm).Light precluding PP or PET/PE or EVA/PP or Aluminum/PE Pouch or PE Pouch with 10-100 impregnated 100% polyester wipes (wipe size: 300x300 mm). |
4.4.1. Use-specific instructions
Allow surface to air dry after using the product. Close container when not in use. Do not use wipes which have become dehydrated. Used wipes must be disposed of in a closed container.
4.4.2. Use-specific risk mitigation measures
Avoid hand to eye transfer.
Use of respiratory protective equipment (RPE) providing a protection factor of 10 is mandatory for professionals applying the product and for other professionals present in the treated area. An air purifying respirator with helmet/hood/mask (TH1/TM1), or a half/full mask with combination filter gas/P2 is at least required (filter type (code letter, colour) to be specified by the authorisation holder within the product information). For repeated application or re-entry into the room, the professional needs to follow the same risk mitigation measures as for the first application in the room.
4.4.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 1.
4.4.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 1.
4.4.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 1.
5. General directions for use of the meta spc 1
5.1. Instructions for use
Always read the label or leaflet before use and follow all the instructions. Clean surface before applying the product. Product should be applied to a clean dry surface. Wet surface completely using the product. Do not rinse after use. Do not use on surfaces sensitive to oxidative agents such as marble, copper or brass.
5.2. Risk mitigation measures
See use-specific risk mitigation measures of meta SPC 1.
5.3. Particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
First aid measures
In case of eye contact: Rinse immediately with plenty of water, including under the eyelids, for at least 15 minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Seek medical attention.
In case of skin contact: Rinse with plenty of water.
If swallowed: Rinse mouth. Seek medical attention if symptoms occur.
If inhaled: Seek medical attention if symptoms occur.
Environmental emergency measures
Do not allow contact with soil, surface or ground water.
Consider the provision of containment around storage vessels.
5.4. Instructions for safe disposal of the product and its packaging
Product: Where possible, recycling is preferred to disposal or incineration. If recycling is not practicable, dispose of in compliance with national regulations. Dispose of waste in an approved waste disposal facility.
Contaminated packaging: Dispose of container in accordance with national regulations.
5.5. Conditions of storage and shelf-life of the product under normal conditions of storage
Keep out of reach of children. Keep container tightly closed. Store in suitable, labelled containers.
Storage temperature: 0-35°C
Shelf life: 24 months
6. Other information
The product contains hydrogen peroxide (CAS No.: 7722-84-1), for which a European reference value of 1,25 mg/m3 for the professional user was agreed and used for the risk assessment of the product.
7. Third information level: individual products in the meta spc 1
7.1. Trade name(s), authorisation number and specific composition of each individual product
| Trade name(s) | Klercide Sporicidal Low Residue Peroxide | Market area: EU | |||
| Klerwipe Sporicidal Low Residue Peroxide | Market area: EU | ||||
| ANIOS H2O2 6% IP STERILE | Market area: EU | ||||
| Authorisation number | EU-0024303-0001 1-1 | ||||
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| Hydrogen peroxide | active substance | 7722-84-1 | 231-765-0 | 6 % (w/w) |
1. Meta spc 2 administrative information
1.1. Meta SPC 2 identifier
| Identifier | Meta SPC: META SPC 2 |
1.2. Suffix to the authorisation number
| Number | 1-2 |
1.3. Product type(s)
| Product type(s) | PT02: Disinfectants and algaecides not intended for direct application to humans or animalsPT04: Food and feed area |
2. Meta spc 2 composition
2.1. Qualitative and quantitative information on the composition of the meta SPC 2
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
|---|---|---|---|---|---|
| Hydrogen peroxide | active substance | 7722-84-1 | 231-765-0 | 1 - 1 % (w/w) |
2.2. Type(s) of formulation of the meta SPC 2
| Formulation type(s) | AL Any other liquid |
3. Hazard and precautionary statements of the meta spc 2
| Hazard statements | |
| Precautionary statements |
4. Authorised use(s) of the meta spc
4.1. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: MycobacteriaCommon name: MycobacteriaDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Spraying using trigger sprayer and dry wipeDetailed description:Disinfection of small surfaces in industry.Contact times for spraying at 20oC in dirty conditions:5 minutes for bacteria and yeasts;15 minutes for fungi;60 minutes for mycobacteria.Method: Mopping using flat mop and bucketDetailed description:Disinfection of large surfaces in industry. Contact times for mopping at 20oC in dirty conditions:5 minutes for bacteria and yeasts;15 minutes for fungi;60 minutes for mycobacteria.Method: Spraying using trigger sprayer and dry wipe and mopping using flat mop and bucket.Detailed description:Disinfection of small and large surfaces in industry.Contact times for spraying and mopping at 20oC in dirty conditions:5 minutes for bacteria and yeasts;15 minutes for fungi;60 minutes for mycobacteria. |
| Application rate(s) and frequency | Application rate:Application rate for spraying: 10 ml/m2Dilution (%):RTU productNumber and timing of application:Application frequency for trigger spraying: up to 10 times per day per roomApplication rate:Application rate for mopping: 20 ml/m2Dilution (%):RTU productNumber and timing of application:Application frequency for mopping: up to twice per day per roomApplication rate:Application rate for spraying: 10 ml/m2; Application rate for mopping: 20 ml/m2Dilution (%):RTU productNumber and timing of application:Application frequency for combined trigger spraying and mopping: once per day per room. |
| Category(ies) of users | professional |
| Pack sizes and packaging material | Light precluding HDPE Container, 1-100LLight precluding HDPE Jerry can, 1-100LLight precluding HDPE IBC, 600-1000LLight precluding HDPE Drum, 60-220LLight precluding HDPE Bottle, 0,1-5LLight precluding HDPE; PE Spray bottle, 0,5-1L |
4.1.1. Use-specific instructions
Spraying: For optimum results, hold the bottle upright and spray from a distance of 30 cm. Spray the product onto the surface, wait for 5 minutes and then wipe the surface with a clean, dry wipe or let air dry. Always close the nozzle after use. Used wipes must be disposed of in a closed container.
Mopping: Remove excess water using a dry floor mop. Fill the bucket with ready-to use product and distribute across floor using flat mop. Wait 5 minutes, then wipe the surface with a clean, dry mop or let air dry.
4.1.2. Use-specific risk mitigation measures
For spraying of large surface areas the following applies: The area of the surface to be disinfected (in m2) must not be larger than 1/10 of the room volume (in m3) e.g. in a room of 120 m3 volume, the maximum surface to be disinfected is 12 m2.
For spraying of small surface areas the above specific risk mitigation measure does not apply.
4.1.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 2.
4.1.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 2.
4.1.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 2.
4.2. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: MycobacteriaCommon name: MycobacteriaDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Mopping using flat mop and bucketDetailed description:Disinfection of small surfaces (floors) in industry plants Contact times for mopping at 20oC in dirty conditions:5 minutes for bacteria and yeasts;15 minutes for fungi;60 minutes for mycobacteria. |
| Application rate(s) and frequency | Application rate:Application rate: 20 ml/m2Dilution (%):RTU productNumber and timing of application:Application frequency: up to twice per day per room |
| Category(ies) of users | professional |
| Pack sizes and packaging material | Light precluding HDPE Container, 1-100 LLight precluding HDPE Jerry can, 1-100 LLight precluding HDPE IBC, 600-1000 LLight precluding HDPE Drum, 60-220 LLight precluding HDPE Bottle, 0,1-5 L |
4.2.1. Use-specific instructions
Fill the bucket with ready-to-use product and distribute across floor using flat mop, afterwards wipe the surface with a clean, dry mop or let air dry.
4.2.2. Use-specific risk mitigation measuresNone
4.2.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 2.
4.2.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 2
4.2.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 2
4.3. Use description
| Product type | PT04: Food and feed area |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: MycobacteriaCommon name: MycobacteriaDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Spraying using trigger sprayer and dry wipeDetailed description:Disinfection of small surfaces in food processing plants. Contact time for spraying at 20oC in dirty conditions:5 minutes for bacteria and yeasts.Contact times for spraying and wiping at 20oC in dirty conditions:5 minutes for bacteria and yeasts;15 minutes for fungi;60 minutes for mycobacteria. |
| Application rate(s) and frequency | Application rate:Application rate: 10 ml/m2Dilution (%):RTU productNumber and timing of application:Application frequency: up to 10 times per day per room |
| Category(ies) of users | professional |
| Pack sizes and packaging material | Light precluding HDPE Container, 1-100 LLight precluding HDPE Jerry can, 1-100 LLight precluding HDPE IBC, 600-1000 LLight precluding HDPE Drum, 60-220 LLight precluding HDPE Bottle, 0,1-5 LLight precluding HDPE; PE Spray bottle, 0,5-1 L |
4.3.1. Use-specific instructions
For optimum results, hold the bottle upright and spray from a distance of 30 cm. Spray the product onto the surface, leave for the required contact time and then either remove excess liquid with dry wipe or let air dry. Always close the nozzle after use. Used wipes must be disposed of in a closed container.
4.3.2. Use-specific risk mitigation measures
Keep food, feed or beverages away from treated surfaces until dried. Do not use directly on or near food, feed or drinks.
4.3.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 2.
4.3.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 2.
4.3.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 2.
4.4. Use description
| Product type | PT04: Food and feed area |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Fixed installed sprayingDetailed description:Automated disinfection application in industrial process equipment. Contact time for spraying at 20oC in dirty conditions:5 minutes for bacteria and yeasts. |
| Application rate(s) and frequency | Application rate:Application rate: 300 L maximum per applicationDilution (%):RTU productNumber and timing of application:Application frequency: once per week |
| Category(ies) of users | professional |
| Pack sizes and packaging material | Light precluding HDPE Container, 1-100 LLight precluding HDPE Jerry can, 1-100 LLight precluding HDPE IBC, 600-1000 LLight precluding HDPE Drum, 60-220 LLight precluding HDPE Bottle, 0,1-5 L |
4.4.1. Use-specific instructions
Use outside food production time, once per week.
4.4.2. Use-specific risk mitigation measures
Application only after the working shift/overnight application.
During spraying application, no person shall be present.
To determine the appropriate re-entry time after application of the product, workplace release measurements using suitable measurement equipment shall be performed upon implementation of the fixed installed spraying, and at regular intervals thereafter (annual intervals recommended), and after any change in relevant boundary conditions. The national regulations for workplace measurements shall be followed. In case of unscheduled maintenance tasks during spraying application, use of respiratory protective equipment (RPE) providing a protection factor of 10 is mandatory.
4.4.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 2.
4.4.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 2.
4.4.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 2.
5. General directions for use of the meta spc 2
5.1. Instructions for use
Always read the label or leaflet before use and follow all the instructions. The product should be applied to a dry surface. Wet surface completely using the product. Do not rinse after use. Do not use on surfaces sensitive to oxidative agents such as marble, copper or brass.
5.2. Risk mitigation measures
See use-specific risk mitigation measures of meta SPC 2.
5.3. Particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
First aid measures
In case of eye contact: Rinse with plenty of water.
In case of skin contact: Rinse with plenty of water.
If swallowed: Rinse mouth. Seek medical attention if symptoms occur.
If inhaled: Seek medical attention if symptoms occur.
Environmental emergency measures
Do not allow contact with soil, surface or ground water.
Consider the provision of containment around storage vessels.
5.4. Instructions for safe disposal of the product and its packaging
Product: Where possible, recycling is preferred to disposal or incineration. If recycling is not practicable, dispose of in compliance with national regulations. Dispose of waste in an approved waste disposal facility.
Contaminated packaging: Dispose of container in accordance with national regulations.
5.5. Conditions of storage and shelf-life of the product under normal conditions of storage
Keep out of reach of children. Keep container tightly closed. Store in suitable, labelled containers.
Storage temperature:0-35 °C
Shelf life: 24 months
6. Other information
The product contains hydrogen peroxide (CAS No.: 7722-84-1), for which a European reference value of 1,25 mg/m3 for the professional user was agreed and used for the risk assessment of the product.
7. Third information level: individual products in the meta spc 2
7.1. Trade name(s), authorisation number and specific composition of each individual product
| Trade name(s) | DrySan Oxy | Market area: EU | |||
| Authorisation number | EU-0024303-0002 1-2 | ||||
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| Hydrogen peroxide | active substance | 7722-84-1 | 231-765-0 | 1 % (w/w) |
1. Meta spc 3 administrative information
1.1. Meta SPC 3 identifier
| Identifier | Meta SPC: META SPC 3 |
1.2. Suffix to the authorisation number
| Number | 1-3 |
1.3. Product type(s)
| Product type(s) | PT04: Food and feed area |
2. Meta spc 3 composition
2.1. Qualitative and quantitative information on the composition of the meta SPC 3
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
|---|---|---|---|---|---|
| Hydrogen peroxide | active substance | 7722-84-1 | 231-765-0 | 35 - 36,75 % (w/w) |
2.2. Type(s) of formulation of the meta SPC 3
| Formulation type(s) | AL - Any other liquid |
3. Hazard and precautionary statements of the meta spc 3
| Hazard statements | H272: May intensify fire; oxidiser.H302: Harmful if swallowed.H315: Causes skin irritation.H318: Causes serious eye damage.H335: May cause respiratory irritation.H412: Harmful to aquatic life with long lasting effects. |
| Precautionary statements | P210: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.P220: Keep away from clothing or other combustible materials.P261: Avoid breathing vapours.P261: Avoid breathing spray.P264: Wash hands thoroughly after handling.P270: Do not eat, drink or smoke when using this product.P271: Use only outdoors or in a well-ventilated area.P273: Avoid release to the environment.P280: Wear eye protection.P280: Wear face protection.P280: Wear protective gloves.P301+P312: IF SWALLOWED: Call a POISON CENTER if you feel unwell.P330: Rinse mouth.P302+P352: IF ON SKIN: Wash with plenty of water.P332+P313: If skin irritation occurs: Get medical advice.P332+P313: If skin irritation occurs: Get medical attention.P304+P340: IF INHALED: Remove person to fresh air and keep comfortable for breathing.P312: Call a POISON CENTER if you feel unwell.P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.P310: Immediately call a POISON CENTER.P310: Immediately call a doctor.P321: Specific treatment (see first aid instruction on this label).P362+P364: Take off contaminated clothing and wash it before reuse.P370+P378: In case of fire: Use water to extinguish.P403+P233: Store in a well-ventilated place. Keep container tightly closed.P405: Store locked up.P501: Dispose of contents to in accordance with national regulations.P501: Dispose of container to in accordance with national regulations. |
4. Authorised use(s) of the meta spc
4.1. Use description
| Product type | PT04: Food and feed area |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: Bacterial sporesCommon name: Bacterial sporesDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Automated dipping or spraying in closed systemDetailed description:Disinfection of packaging (aseptic filling) by fully automated dipping and spraying (closed process). Packaging disinfection in food, beverage and feed manufacturing (dip and spray application). Contact time for dipping and spraying at 60oC in clean conditions:1 minute for bacteria, yeasts, fungi and bacterial spores. |
| Application rate(s) and frequency | Application rate:Application rate: constant automated dosingDilution (%): RTU productNumber and timing of application:Application frequency: constant automated dosing |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Light precluding HDPE Bulk delivery container, > 1 L - bulkLight precluding HDPE Jerry can, 1-100 LLight precluding HDPE IBC, 600-1000 LLight precluding HDPE Drum, 60-220 LLight precluding HDPE Bottle, 0,1-5 L |
4.1.1. Use-specific instructions
—Dosing of product directly into the packaging to disinfect or applied into additional steam
—Continuous use of the product
—Application temperature: 60°C
—Application takes place in a closed and vented system.
Packaging disinfection in food, beverage and feed manufacturing (spraying or dipping application):
Do not rinse after use. After sterilisation, blow-dry the packaging with hot sterile air.
4.1.2. Use-specific risk mitigation measures
1.The product shall only be transferred in closed pipes after mixing and loading. Open product and waste water flows are not allowed.
2.Workplace release measurements using suitable measurement equipment shall be performed upon implementation of the aseptic packaging plant, and at regular intervals thereafter (annual intervals recommended), and after any change in relevant boundary conditions. The national regulations for workplace measurements shall be followed.
3.In case of maintenance of the aseptic packaging plant (e.g. manual cleaning, technical incidents or repair) appropriate PPE (including respiratory protective equipment, chemical protective gloves, chemical protective coverall, eye protection) is required. The type of RPE, the filter type (code letter, colour) and glove material are to be specified by the authorisation holder within the product information.
Do not breathe vapours/spray.
During operation, ensure adequate ventilation along the machines Local exhaust ventilation (LEV) and in the industrial halls (technical ventilation).
During manual maintenance tasks, ensure adequate ventilation inside the machine (LEV) before opening the doors of the aseptic area.
4.1.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 3.
4.1.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 3.
4.1.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 3.
4.2. Use description
| Product type | PT04: Food and feed area |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no data |
| Field(s) of use | Indoor use |
| Application method(s) | Method: CIPDetailed description:Disinfection in food and beverage industry (food contact).Contact times for closed systems at 60oC in clean conditions:5 minutes for bacteria and yeasts;15 minutes for fungi. |
| Application rate(s) and frequency | Application rate:Application rate: automated dosingDilution (%):RTU productNumber and timing of application:Application frequency: once per day |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Light precluding HDPE Bulk delivery container, > 1 L - bulkLight precluding HDPE Jerry can, 1-100 LLight precluding HDPE IBC, 600-1000 LLight precluding HDPE Drum, 60-220 LLight precluding HDPE Bottle, 0,1-5 L |
4.2.1. Use-specific instructions
Before disinfection, system should be washed. Disinfection of CIP tanks, CIP pumps, pipe work and internal system of the processing equipment for food, beverage and feed, including milking machine hygiene (MMH) (closed systems). Rinse with water after treatment.
4.2.2. Use-specific risk mitigation measures
Keep food, feed or beverages away from treated surface until rinsed off with water.
4.2.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 3.
4.2.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 3.
4.2.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 3.
5. General directions for use of the meta spc 3
5.1. Instructions for use
See use-specific instruction for use of meta SPC 3.
5.2. Risk mitigation measures
Wear protective chemical resistant gloves during product handling phase (glove material to be specified by the authorisation holder within the product information).
The use of eye protection while handling the product is mandatory.
The process of dilution shall be carried out using an automatic dosing system.
5.3. Particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
FIRST AID MEASURES
In case of eye contact: Rinse immediately with plenty of water, including under the eyelids, for at least 15 minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Seek medical attention immediately.
In case of skin contact: Wash off immediately with plenty of water for at least 15 minutes. Use a mild soap if available. Seek medical attention if irritation develops and persists.
If swallowed: Rinse mouth. Seek medical attention if symptoms occur.
If inhaled: Remove person to fresh air. Treat symptomatically. Seek medical attention if symptoms occur.
ENVIRONMENTAL EMERGENCY MEASURES
Do not allow contact with soil, surface or ground water.
Consider the provision of containment around storage vessels.
5.4. Instructions for safe disposal of the product and its packaging
Product: Where possible, recycling is preferred to disposal or incineration. If recycling is not practicable, dispose of in compliance with national regulations. Dispose of waste in an approved waste disposal facility.
Contaminated packaging: Dispose of container in accordance with national regulations.
5.5. Conditions of storage and shelf-life of the product under normal conditions of storage
Keep out of reach of children. Keep container tightly closed. Store in suitable, labelled containers.
Storage temperature: 0 - 35 °C
Shelf life: 24 months
6. Other information
The product contains hydrogen peroxide (CAS No.: 7722-84-1), for which a European reference value of 1,25 mg/m3 for the professional user was agreed and used for the risk assessment of the product.
7. Third information level: individual products in the meta spc 3
7.1. Trade name(s), authorisation number and specific composition of each individual product
| Trade name(s) | Oxypak D | Market area: EU | |||
| Oxypak S | Market area: EU | ||||
| Oxypak S10 | Market area: EU | ||||
| Authorisation number | EU-0024303-0003 1-3 | ||||
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| Hydrogen peroxide | active substance | 7722-84-1 | 231-765-0 | 35 % (w/w) |
1. Meta spc 4 administrative information
1.1. Meta SPC 4 identifier
| Identifier | Meta SPC: META SPC 4 |
1.2. Suffix to the authorisation number
| Number | 1-4 |
1.3. Product type(s)
| Product type(s) | PT03: Veterinary hygiene |
2. Meta spc 4 composition
2.1. Qualitative and quantitative information on the composition of the meta SPC 4
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
|---|---|---|---|---|---|
| Hydrogen peroxide | active substance | 7722-84-1 | 231-765-0 | 1,4 - 1,61 % (w/w) | |
| Citric acid monohydrate | 2-hydroxypropane -1,2,3-tricarboxylic acid | Non-Active substance | 5949-29-1 | 201-069-1 | 0,9 - 0,9 % (w/w) |
| Phenoxyethanol | 2-Phenoxyethanol | Non-Active substance | 122-99-6 | 204-589-7 | 0,9 - 0,9 % (w/w) |
| Sodium lauryl Sulphate | Sodium dodecyl sulphate | Non-Active substance | 151-21-3 | 205-788-1 | 3,88 - 3,88 % (w/w) |
| L-Glutamic acid, N-coco acyl derivs., monosodium salts | Sodium;(4S)-4-amino-5-hydroxy-5-oxopentanoate | Non-Active substance | 68187-32-6 | 269-087-2 | 2 - 2 % (w/w) |
| Sulfuric acid, mono-C12-14-alkyl esters, ammonium salts (Texapon ALS) | Sulfuric acid, mono-C12-14-alkyl esters, ammonium salts | Non-Active substance | 90583-11-2 | 292-209-0 | 1,12 - 1,12 % (w/w) |
2.2. Type(s) of formulation of the meta SPC 4
| Formulation type(s) | AL Any other liquid |
3. Hazard and precautionary statements of the meta spc 4
| Hazard statements | H290: May be corrosive to metals.H319: Causes serious eye irritation. |
| Precautionary statements | P234: Keep only in original packaging.P264: Wash hands thoroughly after handling.P280: Wear eye protection.P280: Wear face protection.P390: Absorb spillage to prevent material damage.P406: Store in a a corrosion-resistant container with a resistant inner liner.P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.P337+P313: If eye irritation persists: Get medical attention.P337+P313: If eye irritation persists: Get medical advice. |
4. Authorised use(s) of the meta spc
4.1. Use description
| Product type | PT03: Veterinary hygiene |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no data |
| Field(s) of use | Indoor use |
| Application method(s) | Method: Manual dipping using a dip/foam cup (pre-milking disinfection)Detailed description:Pre-milking teat disinfection by manual dipping using a dip/foam cup.Contact time for dipping at 30oC in clean conditions:60 seconds for bacteria and yeasts. |
| Application rate(s) and frequency | Application rate:Application rate: 4 ml of product per application (i.e. 1 ml per teat therefore 4 ml product for animals with four teats)Dilution (%):RTU productNumber and timing of application:Application frequency: up to twice per day |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Light precluding HDPE Jugs, 1-100 LLight precluding HDPE Jerry can, 1-100 LLight precluding HDPE IBC, 600-1000 LLight precluding HDPE Drum, 60-220 LLight precluding HDPE Bottle, 0,1-5 LLight precluding HDPE; PE Pouch, 0,5-100 L |
4.1.1. Use-specific instructions
See general directions for use of meta SPC 4.
4.1.2. Use-specific risk mitigation measures
See general directions for use of meta SPC 4.
4.1.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 4.
4.1.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 4.
4.1.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 4.
5. General directions for use of the meta spc 4
5.1. Instructions for use
Always read the label or leaflet before use and follow all the instructions. The product should be applied pre-milking by use of a dipping or foam cup. The product must be brought to room temperature before use.
Clean teat with a dry wipe, fill foam cup with product and press foam cup until foam is generated. Dip teat into the cup. Apply foam for 60 seconds on the teat. Wipe the product away with a clean towel. Do not rinse after use.
5.2. Risk mitigation measures
Avoid splashes and spills.
Avoid hand to eye transfer.
5.3. Particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
FIRST AID MEASURES
In case of eye contact: Rinse immediately with plenty of water, including under the eyelids, for at least 15 minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Seek medical attention.
In case of skin contact: Rinse with plenty of water.
If swallowed: Rinse mouth. Seek medical attention if symptoms occur.
If inhaled: Seek medical attention if symptoms occur.
ENVIRONMENTAL EMERGENCY MEASURES
Do not allow contact with soil, surface or ground water.
Consider the provision of containment around storage vessels.
5.4. Instructions for safe disposal of the product and its packaging
Product: Where possible, recycling is preferred to disposal or incineration. If recycling is not practicable, dispose of in compliance with national regulations. Dispose of waste in an approved waste disposal facility.
Contaminated packaging: Dispose of container in accordance with national regulations.
5.5. Conditions of storage and shelf-life of the product under normal conditions of storage
Keep out of reach of children. Keep container tightly closed. Store in suitable, labelled containers.
Storage temperature: 0-25°C
Shelf life: 18 months
6. Other information
The product contains hydrogen peroxide (CAS No.: 7722-84-1), for which a European reference value of 1,25 mg/m3 for the professional user was agreed and used for the risk assessment of the product.
7. Third information level: individual products in the meta spc 4
7.1. Trade name(s), authorisation number and specific composition of each individual product
| Trade name(s) | OxyFoamPlus | Market area: EU | |||
| MEPA Foampro D | Market area: EU | ||||
| Predip PLUS | Market area: EU | ||||
| Authorisation number | EU-0024303-0004 1-4 | ||||
| Common name | UPAC name | Function | CAS number | EC number | Content (%) |
| Hydrogen peroxide | active substance | 7722-84-1 | 231-765-0 | 1,4 % (w/w) | |
| Citric acid monohydrate | 2-hydroxypropane -1,2,3-tricarboxylic acid | Non-Active substance | 5949-29-1 | 201-069-1 | 0,9 % (w/w) |
| Phenoxyethanol | 2-Phenoxyethanol | Non-Active substance | 122-99-6 | 204-589-7 | 0,9 % (w/w) |
| Sodium lauryl Sulphate | Sodium dodecyl sulphate | Non-Active substance | 151-21-3 | 205-788-1 | 3,88 % (w/w) |
| L-Glutamic acid, N-coco acyl derivs., monosodium salts | Sodium;(4S)-4-amino-5-hydroxy-5-oxopentanoate | Non-Active substance | 68187-32-6 | 269-087-2 | 2 % (w/w) |
| Sulfuric acid, mono-C12-14-alkyl esters, ammonium salts (Texapon ALS) | Sulfuric acid, mono-C12-14-alkyl esters, ammonium salts | Non-Active substance | 90583-11-2 | 292-209-0 | 1,12 % (w/w) |
1. Meta spc 5 administrative information
1.1. Meta SPC 5 identifier
| Identifier | Meta SPC: META SPC 5 |
1.2. Suffix to the authorisation number
| Number | 1-5 |
1.3. Product type(s)
| Product type(s) | PT02: Disinfectants and algaecides not intended for direct application to humans or animalsPT04: Food and feed area |
2. Meta spc 5 composition
2.1. Qualitative and quantitative information on the composition of the meta SPC 5
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
|---|---|---|---|---|---|
| Hydrogen peroxide | active substance | 7722-84-1 | 231-765-0 | 1,5 - 1,5 % (w/w) |
2.2. Type(s) of formulation of the meta SPC 5
| Formulation type(s) | AL Any other liquid |
3. Hazard and precautionary statements of the meta spc 5
| Hazard statements | |
| Precautionary statements |
4. Authorised use(s) of the meta spc
4.1. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: MycobacteriaCommon name: MycobacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: Bacterial sporesCommon name: Bacterial sporesDevelopment stage: no dataScientific name: Clostridium difficileCommon name: Bacterial sporesDevelopment stage: no dataScientific name: VirusesCommon name: VirusesDevelopment stage: no data |
| Field(s) of use | Indoor use |
| Application method(s) | Method: Spraying using trigger sprayer and dry wipeDetailed description:Disinfection of surfaces, materials and equipment in life sciences cleanrooms A - D and supporting environments (e.g. pharmaceutical industry). Transfer disinfection or disinfection of small surfaces.Contact times for spraying and wiping at 20oC in dirty conditions:1 minute for bacteria and yeasts;5 minutes for fungi and mycobacteria;60 minutes for bacterial spores;30 minutes for viruses.Contact times for spraying and wiping at 20oC in clean conditions:5 minutes for Clostridium difficile spores;30 minutes for bacterial spores.Contact times for spraying at 20oC in clean conditions:5 minutes for bacteria, yeasts and fungi;30 minutes for viruses and bacterial spores. |
| Application rate(s) and frequency | Application rate:Application rate: 10 ml/m2Dilution (%):RTU productNumber and timing of application:Application frequency: up to twice per day per room |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Light precluding Polyethylene terephthalate (PET) Spray bottle, 0.25-1 LLight precluding Polypropylene and Polyethylene (PP+PE) Spray bottle, 0.25-1 LLight precluding High Density Poly Ethylene (HDPE) or Poly Ethylene (PE) Bottle, 1-5 L |
4.1.1. Use-specific instructions
When used under clean conditions: clean surface before applying the product. For optimum results, hold the bottle upright and spray from a distance of 10 cm to 20 cm. Spray the product onto a dry wipe and wipe small surfaces such as worktops and equipment, or spray the product onto the surface, wipe the surface with a clean, dry wipe and let air dry. Always close the nozzle after use. Used wipes must be disposed of in a closed container.
4.1.2. Use-specific risk mitigation measures
See general directions for use of meta SPC 5.
4.1.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 5
4.1.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 5.
4.1.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 5
4.2. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: MycobacteriaCommon name: MycobacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: Bacterial sporesCommon name: Bacterial sporesDevelopment stage: no dataScientific name: Clostridium difficileCommon name: Bacterial sporesDevelopment stage: no dataScientific name: VirusesCommon name: VirusesDevelopment stage: no data |
| Field(s) of use | Indoor |
| Application method(s) | Method: Mopping using a flat mop and bucketDetailed description:Disinfection of floors in life sciences cleanrooms and supporting environments (e.g. pharmaceutical industry).Contact times for mopping at 20oC in dirty conditions:1 minute for bacteria and yeasts;5 minutes for fungi and mycobacteria;60 minutes for bacterial spores;30 minutes for viruses.Contact times for mopping at 20oC in clean conditions:5 minutes for Clostridium difficile spores;30 minutes for bacterial spores. |
| Application rate(s) and frequency | Application rate:Application rate: 20 ml/m2Dilution (%):RTU productNumber and timing of application:Application frequency: up to twice per day per room |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Light precluding HDPE or PE Bottle, 1-5 L |
4.2.1. Use-specific instructions
When used under clean conditions: clean surface before applying the product. Apply to surfaces by mopping.
4.2.2. Use-specific risk mitigation measures
See general directions for use of meta SPC 5.
4.2.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 5
4.2.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 5
4.2.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 5
4.3. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: MycobacteriaCommon name: MycobacteriaDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Spraying using trigger spray and dry wipeDetailed description:Routine and non-routine disinfection of small and large surfaces in hospital rooms and medical practices.Contact times for spraying at 20oC in dirty conditions:1 minute for bacteria and yeasts;5 minutes for fungi;15 minutes for mycobacteria. |
| Application rate(s) and frequency | Application rate:Application rate: 10 ml/m2Dilution (%):RTU productNumber and timing of application:Application frequency: up to twice per day per room |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Light precluding PET Spray bottle, 0,25-1 LLight precluding HDPE Jerry can, 1-5 L |
4.3.1. Use-specific instructions
Routine disinfection: Disinfection of surfaces, which might be contaminated with pathogens during medical or nursing processes, on a regular basis to reduce the risk of transmission of such organisms via surfaces.
Non-routine disinfection: Disinfection in specific risk situations (unless differently regulated by national public health authorities).
The product is intended for one-step cleaning and disinfection. For optimum results, hold the bottle upright and spray from a distance of 30 cm. Spray the product onto the surface, then wipe surface with a clean, dry wipe and leave to dry. Always close the nozzle after use. Used wipes must be disposed of in a closed container.
4.3.2. Use-specific risk mitigation measures
The area of the surfaces to be disinfected (in m2) must not be larger than 1/10 of the room volume (in m3) e.g. in a room of 120 m3 volume, the maximum surface to be disinfected is 12 m2.
4.3.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 5.
4.3.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 5.
4.3.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 5.
4.4. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: MycobacteriaCommon name: MycobacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: Bacterial sporesCommon name: Bacterial sporesDevelopment stage: no dataScientific name: Clostridium difficileCommon name: Bacterial sporesDevelopment stage: no dataScientific name: VirusesCommon name: VirusesDevelopment stage: no data |
| Field(s) of use | Indoor |
| Application method(s) | Method: Spraying using trigger spray and dry wipeDetailed description:Routine and non-routine disinfection of small and large surfaces in hospital rooms and medical practices.Contact times for spraying and wiping at 20oC in dirty conditions:1 minute for bacteria and yeasts;5 minutes for fungi and mycobacteria;30 minutes for viruses.Contact times for spraying and wiping at 20oC in clean conditions:60 minutes for Clostridium difficile spores;60 minutes for bacterial spores.Contact times for spraying at 20oC in clean conditions:5 minutes for bacteria, yeasts and fungi;30 minutes for viruses;60 minutes for bacterial spores. |
| Application rate(s) and frequency | Application rate:Application rate: 10 ml/m2Dilution (%):RTU productNumber and timing of application:Application frequency: up to twice per day per room |
| Category(ies) of users | professional |
| Pack sizes and packaging material | Light precluding HDPE Bottle, 1-5 LLight precluding PET Spray bottle, 0,25-1 LLight precluding HDPE Jerry can, 1-5 L |
4.4.1. Use-specific instructions
Routine disinfection: Disinfection of surfaces, which might be contaminated with pathogens during medical or nursing processes, on a regular basis to reduce the risk of transmission of such organisms via surfaces.
Non-routine disinfection: Disinfection in specific risk situations (unless differently regulated by national public health authorities).
The product is intended for one-step cleaning and disinfection. When used under clean conditions: clean surface before applying the product. For optimum results, hold the bottle upright and spray from a distance of 30 cm. Spray the product onto a dry wipe and wipe small surfaces such as worktops and equipment, or spray product onto the surface, then wipe surface with a clean, dry wipe and leave to dry. Always close the nozzle after use. Used wipes must be disposed of in a closed container.
4.4.2. Use-specific risk mitigation measures
The area of the surface to be disinfected (in m2) must not be larger than 1/10 of the room volume (in m3) e.g. in a room of 120 m3 volume, the maximum surface to be disinfected is 12 m2.
4.4.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 5
4.4.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 5
4.4.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 5
4.5. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: MycobacteriaCommon name: MycobacteriaDevelopment stage: no data |
| Field(s) of use | Indoor |
| Application method(s) | Method: Wiping using cloth/wipe and bucketDetailed description:Routine and non-routine disinfection of small and large surfaces in hospital rooms and medical practices.Contact times for wiping at 20oC in dirty conditions:1 minute for bacteria and yeasts;5 minutes for fungi;15 minutes for mycobacteria. |
| Application rate(s) and frequency | Application rate:Application rate: 10 ml/m2Dilution (%):RTU productNumber and timing of application:Application frequency: up to twice per day per room |
| Category(ies) of users | professional |
| Pack sizes and packaging material | Light precluding HDPE Jerry can, 1-5 L |
4.5.1. Use-specific instructions
Routine disinfection: Disinfection of surfaces, which might be contaminated with pathogens during medical or nursing processes, on a regular basis to reduce the risk of transmission of such organisms via surfaces.
Non-routine disinfection: Disinfection in specific risk situations (unless differently regulated by national public health authorities).
The product is intended for one-step cleaning and disinfection. Pour product into a clean bucket and distribute across surface using single-use cloth/wipe and let air dry. Used wipes must be disposed of in a closed container.
4.5.2. Use-specific risk mitigation measures
See general directions for use of meta SPC 5.
4.5.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 5.
4.5.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 5.
4.5.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 5.
4.6. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: MycobacteriaCommon name: MycobacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: Bacterial sporesCommon name: Bacterial sporesDevelopment stage: no dataScientific name: Clostridium difficileCommon name: Bacterial sporesDevelopment stage: no dataScientific name: VirusesCommon name: VirusesDevelopment stage: no data |
| Field(s) of use | Indoor |
| Application method(s) | Method: Wiping using cloth/wipe and bucketDetailed description:Routine and non-routine disinfection of small and large surfaces in hospital rooms and medical practices.Contact times for wiping at 20oC in dirty conditions:1 minute for bacteria and yeasts;5 minutes for fungi and mycobacteria ;30 minutes for viruses.Contact times for wiping at 20oC in clean conditions:60 minutes for Clostridium difficile spores;60 minutes for bacterial spores. |
| Application rate(s) and frequency | Application rate:Application rate: 10 ml/m2Dilution (%):RTU productNumber and timing of application:Application frequency: up to twice per day per room |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Light precluding HDPE Bottle, 1-5 LLight precluding HDPE Jerry can, 1-5 L |
4.6.1. Use-specific instructions
Routine disinfection: Disinfection of surfaces, which might be contaminated with pathogens during medical or nursing processes, on a regular basis to reduce the risk of transmission of such organisms via surfaces.
Non-routine disinfection: Disinfection in specific risk situations (unless differently regulated by national public health authorities).
The product is intended for one-step cleaning and disinfection. When used under clean conditions: clean surface before applying the product. Pour product into a clean bucket and distribute across surface using single-use cloth/wipe and let air dry. Used wipes must be disposed of in a closed container.
4.6.2. Use-specific risk mitigation measures
See general directions for use of meta SPC 5.
4.6.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 5
4.6.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 5.
4.6.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 5
4.7. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: MycobacteriaCommon name: MycobacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: Bacterial sporesCommon name: Bacterial sporesDevelopment stage: no dataScientific name: Clostridium difficileCommon name: Bacterial sporesDevelopment stage: no dataScientific name: VirusesCommon name: VirusesDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Mopping using mop and bucketDetailed description:Non-routine disinfection of larger surfaces in hospital room.Contact times for mopping at 20oC in dirty conditions:1 minute for bacteria and yeasts;5 minutes for fungi and mycobacteria;30 minutes for viruses.Contact times for mopping at 20oC in clean conditions:60 minutes for Clostridium difficile spores;60 minutes for bacterial spores. |
| Application rate(s) and frequency | Application rate:Application rate: 20 ml/m2Dilution (%):RTU productNumber and timing of application:Application frequency: up to twice per day per room |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Light precluding HDPE Bottle, 1-5 LLight precluding HDPE Jerry can, 1-5 L |
4.7.1. Use-specific instructions
Non routine disinfection: Disinfection in specific risk situations (unless differently regulated by national public health authorities).
The product is intended for one-step cleaning and disinfection. When used under clean conditions: clean surface before applying the product. Fill the bucket with ready to use product and distribute across floor using mop and let air dry.
4.7.2. Use-specific risk mitigation measures
See general directions for use of meta SPC 5.
4.7.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 5
4.7.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 5
4.7.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 5
4.8. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: MycobacteriaCommon name: MycobacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: Bacterial sporesCommon name: Bacterial sporesDevelopment stage: no dataScientific name: Clostridium difficileCommon name: Bacterial sporesDevelopment stage: no dataScientific name: VirusesCommon name: VirusesDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Mopping using mop and bucketDetailed description:Non-routine disinfection of larger surfaces in medical practices.Contact times for mopping at 20oC in dirty conditions:1 minute for bacteria and yeasts;5 minutes for fungi and mycobacteria;30 minutes for viruses.Contact times for mopping at 20oC in clean conditions:60 minutes for Clostridium difficile spores;60 minutes for bacterial spores. |
| Application rate(s) and frequency | Application rate:Application rate: 20 ml/m2Dilution (%):RTU productNumber and timing of application:Application frequency: up to twice per day per room |
| Category(ies) of users | professional |
| Pack sizes and packaging material | Light precluding HDPE Bottle, 1-5 LLight precluding HDPE Jerry can, 1-5 L |
4.8.1. Use-specific instructions
Non routine disinfection: Disinfection in specific risk situations (unless differently regulated by national public health authorities).
The product is intended for one-step cleaning and disinfection. When used under clean conditions: clean surface before applying the product. Fill the bucket with ready to use product and distribute across floor using mop, wipe the surface with a clean, dry mop and let air dry.
4.8.2. Use-specific risk mitigation measures
See general directions for use of meta SPC 5.
4.8.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 5.
4.8.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 5
4.8.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 5
4.9. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: MycobacteriaCommon name: MycobacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: Bacterial sporesCommon name: Bacterial sporesDevelopment stage: no dataScientific name: Clostridium difficileCommon name: Bacterial sporesDevelopment stage: no dataScientific name: VirusesCommon name: VirusesDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Spraying using trigger sprayer and dry wipe and mopping using mop and bucketDetailed description:Non-routine disinfection of smaller and larger surfaces in hospital rooms and medical practices.Contact times for spraying and wiping, mopping at 20oC in dirty conditions:1 minute for bacteria and yeasts;5 minutes for fungi and mycobacteria;30 minutes for viruses.Contact times for spraying and wiping, mopping at 20oC in clean conditions:60 minutes for Clostridium difficile spores;60 minutes for bacterial spores.Contact times for spraying at 20oC in clean conditions:5 minutes for bacteria, yeasts and fungi;30 minutes for viruses;60 minutes for bacterial spores.Method: Wiping using cloth/wipe and bucket and mopping using mop and bucketDetailed description:Non-routine disinfection of smaller and larger surfaces in hospital rooms and medical practices.Contact times for wiping and mopping at 20oC in dirty conditions:1 minute for bacteria and yeasts;5 minutes for fungi and mycobacteria;30 minutes for viruses.Contact times for wiping and mopping at 20oC in clean conditions:60 minutes for Clostridium difficile spores;60 minutes for bacterial spores. |
| Application rate(s) and frequency | Application rate:Application rate for spraying: 10 ml/m2; Application rate for mopping: 20 ml/m2Dilution (%): RTU productNumber and timing of application:Application frequency for combined trigger spraying and mopping: up to twice per day per roomApplication rate:Application rate for wiping: 10 ml/m2; Application rate for mopping: 20 ml/m2Dilution (%): RTU productNumber and timing of application:Application frequency for combined wiping and mopping: up to twice per day per room |
| Category(ies) of users | professional |
| Pack sizes and packaging material | Light precluding HDPE Bottle, 1-5 LLight precluding PET Spray bottle, 0,25-1 LLight precluding HDPE Jerry can, 1-5 L |
4.9.1. Use-specific instructions
The product is intended for one-step cleaning and disinfection. When used under clean conditions: clean surface before applying the product.
Non-routine disinfection: Disinfection in specific risk situations (unless differently regulated by national public health authorities).
Spraying using trigger sprayer and wiping using a dry wipe: For optimum results, hold the bottle upright and spray from a distance of 30 cm. Spray the product onto a dry wipe and wipe small surfaces such as worktops and equipment, or spray the product onto the surface, wipe the surface with a clean, dry wipe and let air dry. Always close the nozzle after use. Used wipes must be disposed of in a closed container.
Mopping using mop and bucket: Fill the bucket with ready to use product and distribute across floor using mop, wipe the surface with a clean, dry mop and let air dry.
Wiping using cloth/wipe and bucket: Pour product into a clean bucket and distribute across surface using single-use cloth/wipe, wipe the surface with clean cloth/wipe and let air dry. Used wipes must be disposed of in a closed container.
4.9.2. Use-specific risk mitigation measures
For spraying: The area of the surfaces to be disinfected (in m2) must not be larger than 1/10 of the room volume (in m3) e.g. in a room of 120 m3 volume, the maximum surface to be disinfected is 12 m2.
4.9.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 5
4.9.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 5.
4.9.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 5
4.10. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: MycobacteriaCommon name: MycobacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: Bacterial sporesCommon name: Bacterial sporesDevelopment stage: no dataScientific name: Clostridium difficileCommon name: Bacterial sporesDevelopment stage: no dataScientific name: VirusesCommon name: VirusesDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Spraying using trigger spray and dry wipeDetailed description:Routine disinfection of small surfaces in small non-food areas (e.g. bathrooms).Contact times for spraying and wiping at 20oC in dirty conditions:1 minute for bacteria and yeasts;5 minutes for fungi and mycobacteria;60 minutes for bacterial spores;30 minutes for viruses.Contact times for spraying and wiping at 20oC in clean conditions:5 minutes for Clostridium difficile spores;30 minutes for bacterial spores.Contact times for spraying at 20oC in clean conditions:5 minutes for bacteria, yeasts and fungi;30 minutes for viruses and bacterial spores. |
| Application rate(s) and frequency | Application rate: 10 ml/m2Dilution (%): RTU productNumber and timing of application:Application frequency: up to 10 times per day per room |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Light precluding HDPE Bottle, 1-5 LLight precluding PET Spray bottle, 0,25-1 L |
4.10.1. Use-specific instructions
When used under clean conditions: clean surface before applying the product. For optimum results, hold the bottle upright and spray from a distance of 30 cm. Spray the product onto a dry wipe and wipe small surfaces such as worktops and equipment, or spray the product onto the surface, wipe the surface with a clean, dry wipe and let air dry. Always close the nozzle after use. Used wipes must be disposed of in a closed container.
4.10.2. Use-specific risk mitigation measures
See general directions for use of meta SPC 5.
4.10.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 5
4.10.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 5.
4.10.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 5
4.11. Use description
| Product type | PT04: Food and feed area |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: MycobacteriaCommon name: MycobacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: Bacterial sporesCommon name: Bacterial sporesDevelopment stage: no dataScientific name: Clostridium difficileCommon name: Bacterial sporesDevelopment stage: no dataScientific name: VirusesCommon name: VirusesDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Spraying using trigger spray and dry wipeDetailed description:Routine disinfection of small surfaces in small food areas (e.g. kitchens).Contact times for spraying and wiping at 20oC in dirty conditions:1 minute for bacteria and yeasts;5 minutes for fungi and mycobacteria;60 minutes for bacterial spores;30 minutes for viruses.Contact times for spraying and wiping at 20oC in clean conditions:5 minutes for Clostridium difficile spores;30 minutes for bacterial spores.Contact times spraying at 20oC in clean conditions:5 minutes for bacteria, yeasts and fungi;30 minutes for viruses and bacterial spores. |
| Application rate(s) and frequency | Application rate:Application rate: 10 ml/m2Dilution (%):RTU productNumber and timing of application:Application frequency: up to 10 times per day per room. |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Light precluding HDPE Bottle, 1-5 LLight precluding PET Spray bottle, 0,25-1 L |
4.11.1. Use-specific instructions
When used under clean conditions: clean surface before applying the product. For optimum results, hold the bottle upright and spray from a distance of 30 cm. Spray the product onto a dry wipe and wipe small surfaces such as worktops and equipment, or spray the product onto the surface, wipe the surface with a clean, dry wipe and let air dry. Always close the nozzle after use. Used wipes must be disposed of in a closed container.
4.11.2. Use-specific risk mitigation measures
Keep food, feed or beverages away from treated surface until dried. Do not use directly on or near food, feed or drinks.
4.11.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 5.
4.11.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 5.
4.11.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 5.
5. General directions for use of the meta spc 5
5.1. Instructions for use
Always read the label or leaflet before use and follow all the instructions. The product should be applied to a dry surface. Wet surface completely using the product. Do not rinse after use. Do not use on surfaces sensitive to oxidative agents such as marble, copper or brass.
5.2. Risk mitigation measures
-
5.3. Particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
FIRST AID MEASURES
In case of eye contact: Rinse with plenty of water.
In case of skin contact: Rinse with plenty of water.
If swallowed: Rinse mouth. Seek medical attention if symptoms occur.
If inhaled: Seek medical attention if symptoms occur.
ENVIRONMENTAL EMERGENCY MEASURES
Do not allow contact with soil, surface or ground water.
Consider the provision of containment around storage vessels.
5.4. Instructions for safe disposal of the product and its packaging
Product: Where possible, recycling is preferred to disposal or incineration. If recycling is not practicable, dispose of in compliance with national regulations. Dispose of waste in an approved waste disposal facility.
Contaminated packaging: Dispose of container in accordance with national regulations.
5.5. Conditions of storage and shelf-life of the product under normal conditions of storage
Keep out of reach of children. Keep container tightly closed. Store in suitable, labelled containers.
Storage temperature:0-35 °C. Protect from frost.
Shelf life: 18 months
6. Other information
The product contains hydrogen peroxide (CAS No.: 7722-84-1), for which a European reference value of 1,25 mg/m3 for the professional user was agreed and used for the risk assessment of the product.
7. Third information level: individual products in the meta spc 5
7.1. Trade name(s), authorisation number and specific composition of each individual product
| Trade name(s) | Incidin OxyFoam | Market area: EU | |||
| Authorisation number | EU-0024303-0005 1-5 | ||||
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| Hydrogen peroxide | active substance | 7722-84-1 | 231-765-0 | 1,5 % (w/w) |
7.2. Trade name(s), authorisation number and specific composition of each individual product
| Trade name(s) | Incidin OxyFoam S | Market area: EU | |||
| Klercide Sporicidal Enhanced Peroxide | Market area: EU | ||||
| KitchenPro Oxy Foam S | Market area: EU | ||||
| Anios Low Peroxide IP sterile | Market area: EU | ||||
| Sirafan Oxy | Market area: EU | ||||
| Authorisation number | EU-0024303-0006 1-5 | ||||
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| Hydrogen peroxide | active substance | 7722-84-1 | 231-765-0 | 1,5 % (w/w) |
1. Meta spc 6 administrative information
1.1. Meta SPC 6 identifier
| Identifier | Meta SPC: META SPC 6 |
1.2. Suffix to the authorisation number
| Number | 1-6 |
1.3. Product type(s)
| Product type(s) | PT02: Disinfectants and algaecides not intended for direct application to humans or animalsPT04: Food and feed area |
2. Meta spc 6 composition
2.1. Qualitative and quantitative information on the composition of the meta SPC 6
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
|---|---|---|---|---|---|
| Hydrogen peroxide | active substance | 7722-84-1 | 231-765-0 | 2 - 2,3 % (w/w) | |
| N-propanol | Propan-1-ol | Non-Active substance | 71-23-8 | 200-746-9 | 17,5 - 17,5 % (w/w) |
2.2. Type(s) of formulation of the meta SPC 6
| Formulation type(s) | AL Any other liquid |
3. Hazard and precautionary statements of the meta spc 6
| Hazard statements | H226: Flammable liquid and vapour.H318: Causes serious eye damage. |
| Precautionary statements | P210: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.P233: Keep container tightly closed.P240: Ground and bond container and receiving equipment.P241: Use explosion-proof electrical equipment.P241: Use explosion-proof ventilating equipment.P241: Use explosion-proof lighting equipment.P242: Use non-sparking tools.P243: Take actions to prevent static discharges.P280: Wear eye protection.P280: Wear face protection.P303+P361+P353: IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water [or shower].P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.P310: Immediately call a doctor.P310: Immediately call a POISON CENTER.P370+P378: In case of fire: Use water to extinguish.P403+P235: Store in a well-ventilated place. Keep cool.P501: Dispose of contents to in accordance with national regulations.P501: Dispose of container to in accordance with national regulations. |
4. Authorised use(s) of the meta spc
4.1. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Spraying using trigger sprayer and dry wipeDetailed description:Disinfection of small surfaces in industry (e.g. dining areas, bathrooms).Contact time for spraying at 10oC and 20oC in dirty conditions:5 minutes for bacteria and yeasts.Contact time for spraying at 10oC in clean conditions:1 minute for bacteria and yeasts. |
| Application rate(s) and frequency | Application rate:Application rate: 10 ml/m2Dilution (%):RTU productNumber and timing of application:Application frequency: up to 3 times per day |
| Category(ies) of users | professional |
| Pack sizes and packaging material | Light precluding HDPE Container, 1-100 LLight precluding HDPE Jerry can, 1-100 LLight precluding HDPE IBC, 600-1000 LLight precluding HDPE Drum, 60-220 LLight precluding HDPE Bottle, 0,1-5 LLight precluding HDPE Spray bottle, up to 1 L |
4.1.1. Use-specific instructions
See general directions of use of meta SPC 6.
4.1.2. Use-specific risk mitigation measures
See general directions for use of meta SPC 6.
4.1.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 6.
4.1.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 6.
4.1.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 6.
4.2. Use description
| Product type | PT04: Food and feed area |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Spraying using trigger sprayer and dry wipeDetailed description:Disinfection of small surfaces in food processing plants.Contact time for spraying at 10oC and 20oC in dirty conditions:5 minutes for bacteria and yeasts.Contact time for spraying at 10oC in clean conditions:1 minute for bacteria and yeasts. |
| Application rate(s) and frequency | Application rate:Application rate: 10 ml/m2Dilution (%):RTU productNumber and timing of application:Application frequency: up to 4 times per day |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Light precluding HDPE Container, 1-100 LLight precluding HDPE Jerry can, 1-100 LLight precluding HDPE IBC, 600-1000 LLight precluding HDPE Drum, 60-220 LLight precluding HDPE Bottle, 0,1-5 LLight precluding HDPE Spray bottle, up to 1 L |
4.2.1. Use-specific instructions
See general directions for use of meta SPC 6.
4.2.2. Use-specific risk mitigation measures
Keep food, feed or beverages away from treated surface until dried. Do not use directly on or near food, feed or drinks.
4.2.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 6.
4.2.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 6.
4.2.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 6.
5. General directions for use of the meta spc 6
5.1. Instructions for use
Always read the label or leaflet before use and follow all the instructions. When used under clean conditions: clean surface before applying the product. The product should be applied to a dry surface. For optimum results, hold the bottle upright and spray from a distance of 10 cm to 20 cm. Spray the product onto the surface, wipe the surface with a clean, dry wipe or let air dry. Always close the nozzle after use. Wet surface completely using the product. Do not rinse after use. Do not use on surfaces sensitive to oxidative agents such as marble, copper or brass. Used wipes must be disposed of in a closed container.
5.2. Risk mitigation measures
The use of eye protection while handling of the product is mandatory.
5.3. Particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
FIRST AID MEASURES
In case of eye contact: Rinse immediately with plenty of water, including under the eyelids, for at least 15 minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Seek medical attention immediately.
In case of skin contact: Rinse with plenty of water.
If swallowed: Rinse mouth. Seek medical attention if symptoms occur.
If inhaled: Remove person to fresh air. Treat symptomatically. Seek medical attention if symptoms occur.
ENVIRONMENTAL EMERGENCY MEASURES
Do not allow contact with soil, surface or ground water.
Consider the provision of containment around storage vessels.
5.4. Instructions for safe disposal of the product and its packaging
Product: Where possible, recycling is preferred to disposal or incineration. If recycling is not practicable, dispose of in compliance with national regulations. Dispose of waste in an approved waste disposal facility.
Contaminated packaging: Dispose of container in accordance with national regulations.
5.5. Conditions of storage and shelf-life of the product under normal conditions of storage
Keep out of reach of children. Keep container tightly closed. Store in suitable, labelled containers. Keep away from heat and sources of ignition. Keep in a cool, well-ventilated place. Keep away from oxidizing agents.
Storage temperature: 0-30°C
Shelf life: 24 months
6. Other information
The product contains hydrogen peroxide (CAS No.: 7722-84-1), for which a European reference value of 1,25 mg/m3 for the professional user was agreed and used for the risk assessment of the product.
7. Third information level: individual products in the meta spc 6
7.1. Trade name(s), authorisation number and specific composition of each individual product
| Trade name(s) | OxyDes Rapid | Market area: EU | |||
| Authorisation number | EU-0024303-0007 1-6 | ||||
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| Hydrogen peroxide | Active substance | 7722-84-1 | 231-765-0 | 2 % (w/w) | |
| N-propanol | Propan-1-ol | Non-Active substance | 71-23-8 | 200-746-9 | 17,5 % (w/w) |
1. Meta spc 7 administrative information
1.1. Meta SPC 7 identifier
| Identifier | Meta SPC: META SPC 7 |
1.2. Suffix to the authorisation number
| Number | 1-7 |
1.3. Product type(s)
| Product type(s) | PT02: Disinfectants and algaecides not intended for direct application to humans or animalsPT04: Food and feed area |
2. Meta spc 7 composition
2.1. Qualitative and quantitative information on the composition of the meta SPC 7
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
|---|---|---|---|---|---|
| Hydrogen peroxide | active substance | 7722-84-1 | 231-765-0 | 4,95 - 5,45 % (w/w) | |
| Capryleth-9 Carboxylic acid (mixture of alkyl ether carboxylic acid) | Poly(oxy-1,2-ethanediyl), .alpha.-(carboxymethyl)-.omega.-(octyloxy)- (4-11 EO) | Non-Active substance | 53563-70-5 | 2,15 - 2,15 % (w/w) | |
| Hexeth-4 Carboxylic Acid (mixture of alkyl ether carboxylic acid) | Poly(oxy-1,2-ethanediyl), .alpha.-(carboxymethyl)-.omega.-(hexyloxy)- (3 EO) | Non-Active substance | 105391-15-9 | 0,62 - 0,62 % (w/w) |
2.2. Type(s) of formulation of the meta SPC 7
| Formulation type(s) | SL Soluble concentrate |
3. Hazard and precautionary statements of the meta spc 7
| Hazard statements | H314: Causes severe skin burns and eye damage. |
| Precautionary statements | P260: Do not breathe spray.P260: Do not breathe vapours.P264: Wash hands thoroughly after handling.P280: Wear eye protection.P280: Wear face protection.P280: Wear protective gloves.P280: Wear protective clothing.P301+P330+P331: IF SWALLOWED: rinse mouth. Do NOT induce vomiting.P303+P361+P353: IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water [or shower].P310: Immediately call a POISON CENTER.P310: Immediately call a doctor.P304+P340: IF INHALED: Remove person to fresh air and keep comfortable for breathing.P321: Specific treatment (see first aid instruction on this label).P363: Wash contaminated clothing before reuse.P405: Store locked up.P501: Dispose of contents to in accordance with national regulations.P501: Dispose of container to in accordance with national regulations. |
4. Authorised use(s) of the meta spc
4.1. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Mopping using flat mop and bucketDetailed description:Routine and non-routine disinfection of floors in hospital rooms and medical practices that are frequently touched by people and that are not frequently touched by people.Contact times for mopping at 20oC in clean conditions:5 minutes for bacteria and yeasts (10 % dilution);15 minutes for bacteria (7,5 % dilution). |
| Application rate(s) and frequency | Application rate:Application rate: 20 ml/m2Dilution (%):Dilution (%): 7,5-10Number and timing of application:Application frequency: up to 10 times per day per room |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Light precluding HDPE Bottle, 0,5-5 LLight precluding HDPE Canister, 1-100 LLight precluding HDPE Pouch, 0,01-1 LLight precluding HDPE Jug, 0,5-5 L |
4.1.1. Use-specific instructions
Routine disinfection: Disinfection of surfaces, which might be contaminated with pathogens during medical or nursing processes, on a regular basis to reduce the risk of transmission of such organisms via surfaces.
Non-routine disinfection: Disinfection in specific risk situations (unless differently regulated by national public health authorities).
The product is intended for one-step cleaning and disinfection. Clean surface before applying the product. Fill the bucket with diluted product and distribute across floor using flat mop, wipe the surface with clean, dry floor mop and let air dry. Do not rinse after use.
4.1.2. Use-specific risk mitigation measures
See general directions for use of meta SPC 7.
4.1.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 7.
4.1.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 7.
4.1.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 7.
4.2. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Spraying using trigger sprayer and dry wipeDetailed description:Routine disinfection of small surfaces in small non-food areas (e.g. bathrooms).Contact times for spraying at 20oC in clean conditions:5 minutes for bacteria and yeasts (10 % dilution);15 minutes for bacteria (7,5 % dilution).Contact times for spraying at 20oC in dirty conditions:5 minutes for bacteria (10 % dilution);5 minutes for yeasts (15 % dilution);15 minutes for bacteria (7,5 % dilution).Method: Mopping using flat mop and bucketDetailed description:Routine disinfection of large surfaces in small non-food areas (e.g. bathrooms).Contact times for mopping at 20oC in clean conditions:5 minutes for bacteria and yeasts (10 % dilution);15 minutes for bacteria (7,5 % dilution).Method: Spraying using trigger sprayer and dry wipe and mopping using flat mop and bucketDetailed description:Routine disinfection of small and large surfaces in small non-food areas (e.g. bathrooms).Contact times for spraying and mopping at 20oC in clean conditions:5 minutes for bacteria and yeasts (10 % dilution);15 minutes for bacteria (7,5 % dilution).Contact times for spraying at 20oC in dirty conditions:5 minutes for bacteria (10 % dilution);5 minutes for yeasts (15 % dilution);15 minutes for bacteria (7,5 % dilution). |
| Application rate(s) and frequency | Application rate:Application rate for spraying: 10 ml/m2Dilution (%):Dilution (%): 7,5-15Number and timing of application:Application frequency for trigger spraying: up to 10 times per day per roomApplication rate:Application rate for mopping: 20 ml/m2Dilution (%):Dilution (%): 7,5-10Number and timing of application:Application frequency for mopping: up to twice per day per roomApplication rate:Application rate for spraying: 10 ml/m2; Application rate for mopping: 20 ml/m2Dilution (%):Dilution (%): 7,5-15Number and timing of application:Application frequency for combined trigger spraying and mopping: once per day per room. |
| Category(ies) of users | professional |
| Pack sizes and packaging material | Light precluding HDPE Bottle, 0,5-5 LLight precluding HDPE Canister, 1-100 LLight precluding HDPE Pouch, 0,01-1 LLight precluding HDPE jug, 0,5-5 L |
4.2.1. Use-specific instructions
Do not rinse after use.
Spraying: When used under clean conditions: clean surface before applying the product. For optimum results, hold the bottle upright and spray from a distance of 10 cm to 20 cm. Spray the diluted product onto the surface, wipe the surface with a clean, dry wipe and let air dry. Always close the nozzle after use. Used wipes must be disposed of in a closed container.
Mopping: The product is intended for one-step cleaning and disinfection. Clean surface before applying the product. Fill the bucket with diluted product and distribute across floor using flat mop, wipe the surface with clean, dry mop and let air dry.
4.2.2. Use-specific risk mitigation measures
Do not breathe vapours/spray.
For spraying: The area of the surfaces to be disinfected (in m2) must not be larger than 1/10 of the room volume (in m3) e.g. in a room of 120 m3 volume, the maximum surface to be disinfected is 12 m2.
4.2.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 7.
4.2.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 7.
4.2.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 7.
4.3. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Mopping using flat mop and bucketDetailed description:Routine disinfection of large surfaces in large non-food areas.Contact time for mopping at 20oC in clean conditions:5 minutes for bacteria and yeasts (10 % dilution);15 minutes for bacteria (7,5 % dilution). |
| Application rate(s) and frequency | Application rate:Application rate: 20 ml/m2Dilution (%):Dilution (%): 7,5-10Number and timing of application:Application frequency: up to 10 times per day per room |
| Category(ies) of users | professional |
| Pack sizes and packaging material | Light precluding HDPE Bottle, 0,5-5 LLight precluding HDPE Canister, 1-100 LLight precluding HDPE Pouch, 0,01-1 LLight precluding HDPE Jug, 0,5-5 L |
4.3.1. Use-specific instructions
The product is intended for one-step cleaning and disinfection. Clean surface before applying the product. Fill the bucket with diluted product and distribute across floor using flat mop, wipe the surface with a clean, dry floor mop and let air dry. Do not rinse after use.
4.3.2. Use-specific risk mitigation measures
See general directions for use of meta SPC 7.
4.3.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 7.
4.3.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 7.
4.3.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 7.
4.4. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Spraying with a wall-mounted deviceDetailed description:Routine disinfection of large surfaces in large non-food and food areas.Contact times for spraying at 20oC in clean conditions:5 minutes for bacteria and yeasts (10 % dilution);15 minutes for bacteria (7,5 % dilution).Contact times for spraying at 20oC in dirty conditions:5 minutes for bacteria (10 % dilution);5 minutes for yeasts (15 % dilution);15 minutes for bacteria (7,5 % dilution). |
| Application rate(s) and frequency | Application rate:Application rate: 180 ml/m2Dilution (%): 7,5-15Number and timing of application:Application frequency: once per day per room |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Light precluding HDPE Bottle, 0,5-5 LLight precluding HDPE Canister, 1-100 LLight precluding HDPE Pouch, 0,01-1 LLight precluding HDPE Jug, 0,5-5 L |
4.4.1. Use-specific instructions
Apply product via wall-mounted device. When used under clean conditions: clean surface before applying the product. Rinse after application.
4.4.2. Use-specific risk mitigation measures
Do not breathe vapours/spray.
Ensure technical ventilation with at least 15 air exchanges/hour.
4.4.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 7.
4.4.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 7.
4.4.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 7.
4.5. Use description
| Product type | PT04: Food and feed area |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Spraying using trigger sprayer and dry wipeDetailed description:Routine disinfection of large surfaces in large food areas (e.g. kitchens).Contact time for spraying at 20oC in clean conditions:5 minutes for bacteria and yeasts (10 % dilution);w15 minutes for bacteria (7,5 % dilution).Contact times for spraying at 20oC in dirty conditions:5 minutes for bacteria (10 % dilution);5 minutes for yeasts (15 % dilution);15 minutes for bacteria (7,5 % dilution). |
| Application rate(s) and frequency | Application rate:Application rate: 10 ml/m2Dilution (%): 7,5-15Number and timing of application:Application frequency: up to 10 times per day per room |
| Category(ies) of users | professional |
| Pack sizes and packaging material | Light precluding HDPE Bottle, 0,5-5 LLight precluding HDPE Canister, 1-100 LLight precluding HDPE Pouch, 0,01-1 LLight precluding HDPE Jug, 0,5-5 L |
4.5.1. Use-specific instructions
When used under clean conditions: clean surface before applying the product. For optimum results, hold the bottle upright and spray from a distance of 10 cm to 20 cm. Spray the diluted product onto the surface, wipe the surface with a clean, dry wipe and let air dry. Always close the nozzle after use. Do not rinse after use. Used wipes must be disposed of in a closed container.
4.5.2. Use-specific risk mitigation measures
Do not breathe vapours/spray.
Keep food, feed or beverages away from treated surfaces until dried. Do not use directly on or near food, feed or drinks.
The area of the surfaces to be disinfected (in m2) must not be larger than 1/10 of the room volume (in m3) e.g. in a room of 120 m3 volume, the maximum surface to be disinfected is 12 m2.
4.5.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 7.
4.5.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 7.
4.5.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 7.
5. General directions for use of the meta spc 7
5.1. Instructions for use
Always read the label or leaflet before use and follow all the instructions. The product should be applied to a dry surface. Wet surface completely using the product. Do not use on surfaces sensitive to oxidative agents such as marble, copper or brass.
Dilution instruction (7,5%): to produce 1 L of diluted surface disinfectant, add 75 ml of the concentrated product to approximately 500 ml of distilled water or water of equal quality (e.g. demineralised), mix and fill up to 1 L with distilled water or water of equal quality.
Dilution instruction (10%): to produce 1 L of diluted surface disinfectant, add 100 ml of the concentrated product to approximately 500 ml of distilled water or water of equal quality (e.g. demineralised), mix and fill up to 1 L with distilled water or water of equal quality.
Dilution instruction (15%): to produce 1 L of diluted surface disinfectant, add 150 ml of the concentrated product to approximately 500 ml of distilled water or water of equal quality (e.g. demineralised), mix and fill up to 1 L with distilled water or water of equal quality.
5.2. Risk mitigation measures
Wear protective chemical resistant gloves during product handling phase (glove material to be specified by the authorisation holder within the product information).
The use of eye protection while handling the product is mandatory.
5.3. Particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
FIRST AID MEASURES
In case of eye contact: Rinse immediately with plenty of water, including under the eyelids, for at least 15 minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Seek medical attention immediately.
In case of skin contact: Wash off immediately with plenty of water for at least 15 minutes. Use a mild soap if available. Wash clothing before reuse. Thoroughly clean shoes before reuse. Seek medical attention immediately.
If swallowed: Rinse mouth with water. Do NOT induce vomiting. Never give anything by mouth to an unconscious person. Seek medical attention immediately.
If inhaled: Remove person to fresh air. Treat symptomatically. Seek medical attention if symptoms occur.
ENVIRONMENTAL EMERGENCY MEASURES
Do not allow contact with soil, surface or ground water.
Consider the provision of containment around storage vessels.
5.4. Instructions for safe disposal of the product and its packaging
Product: Where possible, recycling is preferred to disposal or incineration. If recycling is not practicable, dispose of in compliance with national regulations. Dispose of waste in an approved waste disposal facility.
Contaminated packaging: Dispose of container in accordance with national regulations.
5.5. Conditions of storage and shelf-life of the product under normal conditions of storage
Keep out of reach of children. Keep container tightly closed. Store in suitable, labelled containers.
Storage temperature: 0-25 °C. Protect from frost.
Shelf life: 18 months
6. Other information
The product contains hydrogen peroxide (CAS No.: 7722-84-1), for which a European reference value of 1,25 mg/m3 for the professional user was agreed and used for the risk assessment of the product.
7. Third information level: individual products in the meta spc 7
7.1. Trade name(s), authorisation number and specific composition of each individual product
| Trade name(s) | Incidin OxyConcentrate | Market area: EU | |||
| UltraSan Floor | Market area: EU | ||||
| Authorisation number | EU-0024303-0008 1-7 | ||||
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| Hydrogen peroxide | active substance | 7722-84-1 | 231-765-0 | 4,95 % (w/w) | |
| Capryleth-9 Carboxylic acid (mixture of alkyl ether carboxylic acid) | Poly(oxy-1,2-ethanediyl), .alpha.-(carboxymethyl)-.omega.-(octyloxy)- (4-11 EO) | Non-Active substance | 53563-70-5 | 2,15 % (w/w) | |
| Hexeth-4 Carboxylic Acid (mixture of alkyl ether carboxylic acid) | Poly(oxy-1,2-ethanediyl), .alpha.-(carboxymethyl)-.omega.-(hexyloxy)- (3 EO) | Non-Active substance | 105391-15-9 | 0,62 % (w/w) |
7.2. Trade name(s), authorisation number and specific composition of each individual product
| Trade name(s) | KitchenPro Oxy Des Super Concentrate | Market area: EU | |||
| Incidin OxyConcentrate FF | Market area: EU | ||||
| CidalSan Large Area | Market area: EU | ||||
| Authorisation number | EU-0024303-0009 1-7 | ||||
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| Hydrogen peroxide | active substance | 7722-84-1 | 231-765-0 | 4,95 % (w/w) | |
| Capryleth-9 Carboxylic acid (mixture of alkyl ether carboxylic acid) | Poly(oxy-1,2-ethanediyl), .alpha.-(carboxymethyl)-.omega.-(octyloxy)- (4-11 EO) | Non-Active substance | 53563-70-5 | 2,15 % (w/w) | |
| Hexeth-4 Carboxylic Acid (mixture of alkyl ether carboxylic acid) | Poly(oxy-1,2-ethanediyl), .alpha.-(carboxymethyl)-.omega.-(hexyloxy)- (3 EO) | Non-Active substance | 105391-15-9 | 0,62 % (w/w) |
1. Meta spc 8 administrative information
1.1. Meta SPC 8 identifier
| Identifier | Meta SPC: META SPC 8 |
1.2. Suffix to the authorisation number
| Number | 1-8 |
1.3. Product type(s)
| Product type(s) | PT02: Disinfectants and algaecides not intended for direct application to humans or animalsPT04: Food and feed area |
2. Meta spc 8 composition
2.1. Qualitative and quantitative information on the composition of the meta SPC 8
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
|---|---|---|---|---|---|
| Hydrogen peroxide | active substance | 7722-84-1 | 231-765-0 | 1 - 1 % (w/w) |
2.2. Type(s) of formulation of the meta SPC 8
| Formulation type(s) | AL - Any other liquid |
3. Hazard and precautionary statements of the meta spc 8
| Hazard statements | |
| Precautionary statements |
4. Authorised use(s) of the meta spc
4.1. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: MycobacteriaCommon name: MycobacteriaDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Wiping using impregnated RTU wipesDetailed description:Disinfection of surfaces in industry (e.g. dining areas, bathrooms).Contact time for wiping at 10oC in dirty conditions:5 minutes for bacteria and yeasts.Contact times for wiping at 20oC in dirty conditions:2 minutes for bacteria;5 minutes for yeasts;15 minutes for fungi;60 minutes for mycobacteria. |
| Application rate(s) and frequency | Application rate:Application rate: 1 wipe per m2 (corresponding to 10 ml/m2)Dilution (%):RTU productNumber and timing of application:Application frequency: up to 10 times per day per room |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Light precluding PP Bucket with 10-5000 impregnated 60% polyester / 40% lyocell blend or non-woven 100% polypropylene wipes (wipe size: 200x250 mm or 200x200 mm).Light precluding PP Pouch with 10-5000 impregnated 60% polyester / 40% lyocell blend or non-woven 100% polypropylene wipes (wipe size: 200x250 mm or 200x200 mm). |
4.1.1. Use-specific instructions
See general directions for use of meta SPC 8.
4.1.2. Use-specific risk mitigation measures
-
4.1.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 8.
4.1.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 8.
4.1.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 8.
4.2. Use description
| Product type | PT04: Food and feed area |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: MycobacteriaCommon name: MycobacteriaDevelopment stage: no data |
| Field(s) of use | Indoor use |
| Application method(s) | Method: Wiping using impregnated RTU wipesDetailed description:Disinfection of small surfaces in food processing plant.Contact time for wiping at 10oC in dirty conditions:5 minutes for bacteria and yeasts.Contact times for wiping at 20oC in dirty conditions:2 minutes for bacteria;5 minutes for yeasts;15 minutes for fungi;60 minutes for mycobacteria. |
| Application rate(s) and frequency | Application rate:Application rate: 1 wipe per m2 (corresponding to 10 ml/m2)Dilution (%):RTU productNumber and timing of application:Application frequency: up to 10 times per day per room |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Light precluding PP Bucket with 10-5000 impregnated 60% polyester / 40% lyocell blend or non-woven 100% polypropylene wipes (wipe size: 200x250 mm or 200x200 mm).Light precluding PP Pouch with 10-5000 impregnated 60% polyester / 40% lyocell blend or non-woven 100% polypropylene wipes (wipe size: 200x250 mm or 200x200 mm). |
4.2.1. Use-specific instructions
See general directions for use of meta SPC 8.
4.2.2. Use-specific risk mitigation measures
Keep food, feed or beverages away from treated surface until dried. Do not use directly on or near food, feed or drinks.
4.2.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 8.
4.2.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 8.
4.2.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 8.
4.3. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: MycobacteriaCommon name: MycobacteriaDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Wiping using impregnated RTU wipesDetailed description:Routine disinfection of smaller surfaces in hospital rooms and medical practices that are not frequently touched by people.Contact time for wiping at 10oC in dirty conditions:5 minutes for bacteria and yeasts.Contact times for wiping at 20oC in dirty conditions:15 minutes for bacteria, yeasts and fungi;60 minutes for mycobacteria. |
| Application rate(s) and frequency | Application rate:Application rate: 1 wipe per m2 (corresponding to 10 ml/m2)Dilution (%):RTU productNumber and timing of application:Application frequency: up to twice per day per room |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Light precluding PP Bucket with 10-5000 impregnated 60% polyester / 40% lyocell blend or non-woven 100% polypropylene wipes (wipe size: 200x250 mm or 200x200 mm).Light precluding PP Pouch with 10-5000 impregnated 60% polyester / 40% lyocell blend or non-woven 100% polypropylene wipes (wipe size: 200x250 mm or 200x200 mm). |
4.3.1. Use-specific instructions
Routine disinfection: Disinfection of surfaces, which might be contaminated with pathogens during medical or nursing processes on a regular basis to reduce the risk of transmission of such organisms via surfaces.
4.3.2. Use-specific risk mitigation measures
-
4.3.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 8.
4.3.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 8.
4.3.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 8.
5. General directions for use of the meta spc 8
5.1. Instructions for use
The product is intended for one-step cleaning and disinfection. Always read the label or leaflet before use and follow all the instructions. The product should be applied to a dry surface. Wet surface completely using the product. Allow surface to air dry after using the product. Do not rinse after use. Close container when not in use. Do not use wipes which have become dehydrated. Dispose of the container when empty. Do not use on surfaces sensitive to oxidative agents such as marble, copper or brass. Used wipes must be disposed of in closed container.
5.2. Risk mitigation measures
-
5.3. Particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
FIRST AID MEASURES
In case of eye contact: Rinse with plenty of water.
In case of skin contact: Rinse with plenty of water.
If swallowed: Rinse mouth. Seek medical attention if symptoms occur.
If inhaled: Seek medical attention if symptoms occur.
ENVIRONMENTAL EMERGENCY MEASURES
Do not allow contact with soil, surface or ground water.
Consider the provision of containment around storage vessels.
5.4. Instructions for safe disposal of the product and its packaging
Product: Where possible, recycling is preferred to disposal or incineration. If recycling is not practicable, dispose of in compliance with national regulations. Dispose of waste in an approved waste disposal facility.
Contaminated packaging: Dispose of container in accordance with national regulations.
5.5. Conditions of storage and shelf-life of the product under normal conditions of storage
Keep out of reach of children. Keep container tightly closed. Store in suitable, labelled containers.
Storage temperature: 0-35 °C. Protect from frost.
Shelf life: 18 months
6. Other information
The product contains hydrogen peroxide (CAS No.: 7722-84-1), for which a European reference value of 1,25 mg/m3 for the professional user was agreed and used for the risk assessment of the product.
7. Third information level: individual products in the meta spc 8
7.1. Trade name(s), authorisation number and specific composition of each individual product
| Trade name(s) | DrySan Oxy Wipes | Market area: EU | |||
| IncidinOxyWipe | Market area: EU | ||||
| Authorisation number | EU-0024303-0010 1-8 | ||||
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| Hydrogen peroxide | active substance | 7722-84-1 | 231-765-0 | 1 % (w/w) |
1. Meta spc 9 administrative information
1.1. Meta SPC 9 identifier
| Identifier | Meta SPC: META SPC 9 |
1.2. Suffix to the authorisation number
| Number | 1-9 |
1.3. Product type(s)
| Product type(s) | PT02: Disinfectants and algaecides not intended for direct application to humans or animalsPT04: Food and feed area |
2. Meta spc 9 composition
2.1. Qualitative and quantitative information on the composition of the meta SPC 9
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
|---|---|---|---|---|---|
| Hydrogen peroxide | active substance | 7722-84-1 | 231-765-0 | 7 - 7,7 % (w/w) | |
| Phosphoric acid | Orthophosphoric acid | Non-Active substance | 7664-38-2 | 231-633-2 | 1,5 - 1,5 % (w/w) |
| Nitric acid | Nitric acid | Non-Active substance | 7697-37-2 | 231-714-2 | 3,71 - 3,71 % (w/w) |
| Alcohol EO phosphate ester | Poly(oxy-1,2-ethanediyl), .alpha.-hydro-.omega.-hydroxy-, mono-C8-10-alkyl ethers, phosphates | Non-Active substance | 68130-47-2 | 14,625 - 14,625 % (w/w) | |
| Alkylpolyglycoside C8-C10 | (3R,4S,5S,6R)-2-decoxy-6-(hydroxymethyl)oxane-3,4,5-triol | Non-Active substance | 68515-73-1 | 500-220-1 | 6,35 - 6,35 % (w/w) |
| Alcohols, C10-C16 ethoxylated propoxylated (Dehydol 980) | Alcohols, C10-C16 ethoxylated propoxylated | Non-Active substance | 69227-22-1 | 3 - 3 % (w/w) |
2.2. Type(s) of formulation of the meta SPC 9
| Formulation type(s) | SL Soluble concentrate |
3. Hazard and precautionary statements of the meta spc 9
| Hazard statements | H290: May be corrosive to metals.H314: Causes severe skin burns and eye damage. |
| Precautionary statements | P234: Keep only in original packaging.P264: Wash hands thoroughly after handling.P260: Do not breathe vapours.P260: Do not breathe spray.P280: Wear face protection.P280: Wear protective gloves.P280: Wear eye protection.P280: Wear protective clothing.P301+P330+P331: IF SWALLOWED: rinse mouth. Do NOT induce vomiting.P303+P361+P353: IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water [or shower].P310: Immediately call a doctor.P310: Immediately call a POISON CENTER.P304+P340: IF INHALED: Remove person to fresh air and keep comfortable for breathing.P321: Specific treatment (see first aid instruction on this label).P363: Wash contaminated clothing before reuse.P390: Absorb spillage to prevent material damage.P406: Store in a a corrosion-resistant container with a resistant inner liner.P405: Store locked up.P501: Dispose of contents to in accordance with national regulations.P501: Dispose of container to in accordance with national regulations. |
4. Authorised use(s) of the meta spc
4.1. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: VirusesCommon name: VirusesDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Wiping using cloth/wipe and bucketDetailed description:Routine and non-routine disinfection of smaller surfaces in hospital rooms and medical practices that are frequently touched by people and that are not frequently touched by people.Contact times for wiping at 20oC in dirty conditions:5 minutes for bacteria (5 % dilution);5 minutes for yeasts (3 % dilution);5 minutes for fungi (4 % dilution);50 minutes for viruses (5 % dilution). |
| Application rate(s) and frequency | Application rate:Application rate: 10 ml/m2Dilution (%): 3-5Number and timing of application:Application frequency: up to 10 times per day per room |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Light precluding HDPE Bottle, 0,5-5 LLight precluding HDPE Jug, 0,5-5 LLight precluding HDPE Pouch, 0,01-1 L |
4.1.1. Use-specific instructions
Routine disinfection: Disinfection of surfaces which might be contaminated with pathogens during medical or nursing processes, on a regular basis, to reduce the risk of transmission of such organisms via surfaces.
Non-routine disinfection: Disinfection in specific risk situations (unless differently regulated by national public health authorities).
The product is intended for one-step cleaning and disinfection. Pour diluted product into a clean bucket and distribute across surface using a single-use cloth/wipe, wipe the surface with a clean cloth/wipe and let air dry. Do not rinse after use. Do not use on surfaces sensitive to oxidative agents such as marble, copper or brass. Used wipes must be disposed of in a closed container.
4.1.2. Use-specific risk mitigation measures
See general directions for use of meta SPC 9.
4.1.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 9.
4.1.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 9.
4.1.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 9.
4.2. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: VirusesCommon name: VirusesDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Mopping using flat mop and bucketDetailed description:Routine and non-routine disinfection of larger surfaces in hospital rooms and medical practices that are frequently touched by people and that are not frequently touched by people.Contact times for mopping at 20oC in dirty conditions:5 minutes for bacteria (5 % dilution);5 minutes for yeasts (3 % dilution);5 minutes for fungi (4 % dilution);50 minutes for viruses (5 % dilution). |
| Application rate(s) and frequency | Application rate:Application rate: 20 ml/m2Dilution (%):Dilution (%): 3-5Number and timing of application:Application frequency: up to 10 times per day per room |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Light precluding HDPE Bottle, 0,5-5 LLight precluding HDPE Jug, 0,5-5 LLight precluding HDPE Pouch, 0,01-1 L |
4.2.1. Use-specific instructions
Routine disinfection: Disinfection of surfaces which might be contaminated with pathogens during medical or nursing processes, on a regular basis to reduce the risk of transmission of such organisms via surfaces.
Non-routine disinfection: Disinfection in specific risk situations (unless differently regulated by national public health authorities).
The product is intended for one-step cleaning and disinfection. Fill the bucket with diluted product and distribute across floor using flat mop, wipe the surface with a clean, dry mop and let air dry. Do not rinse after use.
4.2.2. Use-specific risk mitigation measures
See general directions for use of meta SPC 9.
4.2.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 9.
4.2.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 9.
4.2.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 9.
4.3. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: VirusesCommon name: VirusesDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Spraying using trigger sprayer and dry wipeDetailed description:Routine disinfection of small surfaces in small non-food areas (e.g. bathrooms).Contact times for spraying and wiping at 20oC in dirty conditions:5 minutes for bacteria (5% dilution);5 minutes for yeasts (3% dilution);5 minutes for fungi (4% dilution);50 minutes for viruses (5% dilution).Method: Wiping using single-use cloth/wipe and bucketDetailed description:Routine disinfection of small surfaces in small non-food areas (e.g. bathrooms).Contact times for wiping at 20oC in dirty conditions:5 minutes for bacteria (5% dilution);5 minutes for yeasts (3% dilution);5 minutes for fungi (4% dilution);50 minutes for viruses (5% dilution).Method: Mopping using flat mop and bucketDetailed description:Routine disinfection of large surfaces in small non-food areas (e.g. bathrooms).Contact times for mopping at 20oC in dirty conditions:5 minutes for bacteria (5% dilution);5 minutes for yeasts (3% dilution);5 minutes for fungi (4% dilution);50 minutes for viruses (5% dilution).Method: Spraying using trigger sprayer and dry wipe and mopping using flat mop and bucketDetailed description:Routine disinfection of small and large surfaces in small non-food areas (e.g. bathrooms).Contact times for spraying and wiping, mopping at 20oC in dirty conditions:5 minutes for bacteria (5% dilution);5 minutes for yeasts (3% dilution);5 minutes for fungi (4% dilution);50 minutes for viruses (5% dilution).Method: Wiping using cloth/wipe and bucket and mopping using flat mop and bucketDetailed description:Routine disinfection of small and large surfaces in small non-food areas (e.g. bathrooms).Contact times for wiping and mopping at 20oC in dirty conditions:5 minutes for bacteria (5% dilution);5 minutes for yeasts (3% dilution);5 minutes for fungi (4% dilution);50 minutes for viruses (5% dilution). |
| Application rate(s) and frequency | Application rate:Application rate for spraying: 10 ml/m2Dilution (%):Dilution (%): 3-5Number and timing of application:Application frequency for trigger spraying: up to 10 times per day per roomApplication rate:Application rate for wiping: 10 ml/m2Dilution (%): 3-5Number and timing of application:Application frequency for wiping: up to 10 times per day per roomApplication rate for mopping: 20 ml/m2Dilution (%): 3-5Number and timing of application:Application frequency for mopping: up to twice per day per roomApplication rate:Application rate for spraying: 10 ml/m2;Application rate for mopping: 20 ml/m2Dilution (%): 3-5Number and timing of application:Application frequency for combined trigger spraying and mopping: once per day per room.Application rate:Application rate for wiping: 10 ml/m2;Application rate for mopping: 20 ml/m2Dilution (%): 3-5Number and timing of application:Application frequency for combined wiping and mopping: once per day per room |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Light precluding HDPE Bottle, 0,5-5 LLight precluding HDPE Jug, 0,5-5 LLight precluding HDPE Pouch, 0,01-1 L |
4.3.1. Use-specific instructions
Do not rinse after use.
Spraying: For optimum results, hold the bottle upright and spray from a distance of 30 cm. Spray the diluted product onto a dry wipe and wipe small surfaces such as worktops and equipment, or spray the diluted product onto the surface, wipe the surface with a clean, dry wipe or let air dry. Always close the nozzle after use. Used wipes must be disposed of in a closed container.
Wiping: Pour diluted product into a clean bucket and distribute across surface using single-use cloth/wipe, wipe the surface with a clean cloth/wipe and let air dry. Used wipes must be disposed of in a closed container.
Mopping: Fill the bucket with diluted product and distribute across floor using flat mop, wipe the surface with a clean, dry mop and let air dry.
4.3.2. Use-specific risk mitigation measures
Do not breathe vapours/spray.
For spraying: The area of the surface to be disinfected (in m2) must not be larger than 1/10 of the room volume (in m3) e.g. in a room of 120 m3 volume, the maximum surface to be disinfected is 12 m2.
4.3.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 9.
4.3.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 9.
4.3.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 9.
4.4. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: VirusesCommon name: VirusesDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Mopping using flat mop and bucketDetailed description:Routine disinfection of large surfaces in large non-food areas.Contact times for mopping at 20oC in dirty conditions:5 minutes for bacteria (5% dilution);5 minutes for yeasts (3% dilution);5 minutes for fungi (4% dilution);50 minutes for viruses (5% dilution). |
| Application rate(s) and frequency | Application rate:Application rate: 20 ml/m2Dilution (%): 3-5Number and timing of application:Application frequency: up to 10 times per day per room |
| Category(ies) of users | professional |
| Pack sizes and packaging material | Light precluding HDPE Bottle, 0,5-5 LLight precluding HDPE Jug, 0,5-5 LLight precluding HDPE Pouch, 0,01-1 L |
4.4.1. Use-specific instructions
Fill the bucket with diluted product and distribute across floor using flat mop, wipe the surface with a clean, dry mop and let air dry. Do not rinse after use.
4.4.2. Use-specific risk mitigation measures
Ensure technical ventilation with at least 15 air exchanges/hour.
4.4.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 9.
4.4.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 9.
4.4.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 9.
4.5. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Spraying with a wall- mounted deviceDetailed description:Routine disinfection of large surfaces in large non-food and food areas.Contact time for spraying at 20oC in dirty conditions:5 minutes for bacteria and yeasts (3% dilution).Contact times for spraying at 20oC in clean conditions:5 minutes for bacteria (1,5 % dilution);15 minutes for yeasts (2% dilution). |
| Application rate(s) and frequency | Application rate:Application rate: 180 ml/m2Dilution (%):Dilution (%): 1,5-3Number and timing of application:Application frequency: once per day per room |
| Category(ies) of users | professional |
| Pack sizes and packaging material | Light precluding HDPE Bottle, 0,5-5 LLight precluding HDPE Jug, 0,5-5 LLight precluding HDPE Pouch, 0,01-1 L |
4.5.1. Use-specific instructions
When used under clean conditions: clean surface before applying the product. Apply product via wall-mounted device. Rinse after application.
4.5.2. Use-specific risk mitigation measures
Do not breathe vapours/spray.
Ensure technical ventilation with at least 15 air exchanges/hour.
4.5.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 9.
4.5.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 9.
4.5.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 9.
4.6. Use description
| Product type | PT04: Food and feed area |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: VirusesCommon name: VirusesDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Spraying using trigger spray and dry wipeDetailed description:Routine disinfection of large surfaces in large food areas (e.g. kitchens).Contact times for spraying and wiping at 20oC in dirty conditions:5 minutes for bacteria (5% dilution);5 minutes for yeasts (3% dilution);5 minutes for fungi (4% dilution);50 minutes for viruses (5% dilution). |
| Application rate(s) and frequency | Application rate:Application rate: 10 ml/m2Dilution (%):Dilution (%): 3-5Number and timing of application:Application frequency: up to 10 times per day per room |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Light precluding HDPE Bottle, 0,5-5 LLight precluding HDPE Jug, 0,5-5 LLight precluding HDPE Pouch, 0,01-1 L |
4.6.1. Use-specific instructions
For optimum results, hold the bottle upright and spray from a distance of 30 cm. Spray the diluted product onto a dry wipe and wipe small surfaces such as worktops and equipment or spray the diluted product onto the surface, wipe the surface with a clean, dry wipe and let air dry. Always close the nozzle after use. Do not rinse after use. Used wipes must be disposed of in a closed container.
4.6.2. Use-specific risk mitigation measures
Do not breathe vapours/spray.
Keep food, feed or beverages away from treated surface until dried. Do not use directly on or near food, feed or drinks.
The area of the surface to be disinfected (in m2) must not be larger than 1/10 of the room volume (in m3) e.g. in a room of 120 m3 volume, the maximum surface to be disinfected is 12 m2.
4.6.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 9.
4.6.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 9.
4.6.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 9.
4.7. Use description
| Product type | PT04: Food and feed area |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: VirusesCommon name: VirusesDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Wiping using single-use cloth/wipe and bucketDetailed description:Routine disinfection of large surfaces in large food areas (e.g. kitchens).Contact times for wiping at 20oC in dirty conditions:5 minutes for bacteria (5% dilution);5 minutes for yeasts (3% dilution);5 minutes for fungi (4% dilution);50 minutes for viruses (5% dilution). |
| Application rate(s) and frequency | Application rate: 10 ml/m2Dilution (%): 3-5Number and timing of application:Application frequency: up to 10 times per day per room |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Light precluding HDPE Bottle, 0,5-5 LLight precluding HDPE Jug, 0,5-5 LLight precluding HDPE Pouch, 0,01-1 L |
4.7.1. Use-specific instructions
Pour diluted product into a clean bucket and distribute across surface using single-use cloth/wipe, wipe the surface with a clean cloth/wipe and let air dry. Do not rinse after use. Used wipes must be disposed of in a closed container.
4.7.2. Use-specific risk mitigation measures
Keep food, feed or beverages away from treated surface until dried. Do not use directly on or near food, feed or drinks.
4.7.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 9.
4.7.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 9.
4.7.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 9.
5. General directions for use of the meta spc 9
5.1. Instructions for use
Always read the label or leaflet before use and follow all the instructions. The product should be applied to a dry surface. Wet surface completely using the product. Do not use on surfaces sensitive to oxidative agents such as marble, copper or brass.
Dilution instruction (1,5 %): to produce 1 L of diluted surface disinfectant, add 15 ml of the concentrated product to approximately 500 ml of distilled water or water of equal quality (e.g. demineralised), mix and fill up to 1 L with distilled water or water of equal quality.
Dilution instruction (2%): to produce 1 L of diluted surface disinfectant, add 20 ml of the concentrated product to approximately 500 ml of distilled water or water of equal quality (e.g. demineralised), mix and fill up to 1 L with distilled water or water of equal quality.
Dilution instruction (3%): to produce 1 L of diluted surface disinfectant, add 30 ml of the concentrated product to approximately 500 ml of distilled water or water of equal quality (e.g. demineralised), mix and fill up to 1 L with distilled water or water of equal quality.
Dilution instruction (4%): to produce 1 L of diluted surface disinfectant, add 40 ml of the concentrated product to approximately 500 ml of distilled water or water of equal quality (e.g. demineralised), mix and fill up to 1 L with distilled water or water of equal quality.
Dilution instruction (5%): to produce 1 L of diluted surface disinfectant, add 50 ml of the concentrated product to approximately 500 ml of distilled water or water of equal quality (e.g. demineralised), mix and fill up to 1 L with distilled water or water of equal quality.
5.2. Risk mitigation measures
Wear protective chemical resistant gloves during product handling phase (glove material to be specified by the authorisation holder within the product information).
The use of eye protection while handling the product is mandatory.
5.3. Particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
FIRST AID MEASURES
In case of eye contact: Rinse immediately with plenty of water, including under the eyelids, for at least 15 minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Seek medical attention immediately.
In case of skin contact: Wash off immediately with plenty of water for at least 15 minutes. Use a mild soap if available. Wash contaminated clothing before reuse. Thoroughly clean shoes before reuse. Seek medical attention immediately.
If swallowed: Rinse mouth with water. Do NOT induce vomiting. Never give anything by mouth to an unconscious person. Seek medical attention immediately.
If inhaled: Remove person to fresh air. Treat symptomatically. Seek medical attention if symptoms occur.
ENVIRONMENTAL EMERGENCY MEASURES
Do not allow contact with soil, surface or ground water.
Consider the provision of containment around storage vessels.
5.4. Instructions for safe disposal of the product and its packaging
Product: Where possible, recycling is preferred to disposal or incineration. If recycling is not practicable, dispose of in compliance with national regulations. Dispose of waste in an approved waste disposal facility.
Contaminated packaging: Dispose of container in accordance with national regulations.
5.5. Conditions of storage and shelf-life of the product under normal conditions of storage
Keep out of reach of children. Keep container tightly closed. Store in suitable, labelled containers.
Storage temperature: 0-25 °C. Protect from frost.
Shelf life: 18 months
6. Other information
The product contains hydrogen peroxide (CAS No.: 7722-84-1), for which a European reference value of 1,25 mg/m3 for the professional user was agreed and used for the risk assessment of the product.
7. Third information level: individual products in the meta spc 9
7.1. Trade name(s), authorisation number and specific composition of each individual product
| Trade name(s) | KitchenPro Oxy Des Concentrate | Market area: EU | |||
| Incidin OxyPro | Market area: EU | ||||
| Sirafan Oxy Conc | Market area: EU | ||||
| Authorisation number | EU-0024303-0011 1-9 | ||||
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| Hydrogen peroxide | active substance | 7722-84-1 | 231-765-0 | 7 % (w/w) | |
| Phosphoric acid | Orthophosphoric acid | Non-Active substance | 7664-38-2 | 231-633-2 | 1,5 % (w/w) |
| Nitric acid | Nitric acid | Non-Active substance | 7697-37-2 | 231-714-2 | 3,71 % (w/w) |
| Alcohol EO phosphate ester | Poly(oxy-1,2-ethanediyl), .alpha.-hydro-.omega.-hydroxy-, mono-C8-10-alkyl ethers, phosphates | Non-Active substance | 68130-47-2 | 14,625 % (w/w) | |
| Alkylpolyglycoside C8-C10 | (3R,4S,5S,6R)-2-decoxy-6-(hydroxymethyl)oxane-3,4,5-triol | Non-Active substance | 68515-73-1 | 500-220-1 | 6,35 % (w/w) |
| Alcohols, C10-C16 ethoxylated propoxylated (Dehydol 980) | Alcohols, C10-C16 ethoxylated propoxylated | Non-Active substance | 69227-22-1 | 3 % (w/w) |
7.2. Trade name(s), authorisation number and specific composition of each individual product
| Trade name(s) | Oasis Pro Oxy Des | Market area: EU | |||
| Maxx Oxy Des 2 | Market area: EU | ||||
| Authorisation number | EU-0024303-0012 1-9 | ||||
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| Hydrogen peroxide | active substance | 7722-84-1 | 231-765-0 | 7 % (w/w) | |
| Phosphoric acid | Orthophosphoric acid | Non-Active substance | 7664-38-2 | 231-633-2 | 1,5 % (w/w) |
| Nitric acid | Nitric acid | Non-Active substance | 7697-37-2 | 231-714-2 | 3,71 % (w/w) |
| Alcohol EO phosphate ester | Poly(oxy-1,2-ethanediyl), .alpha.-hydro-.omega.-hydroxy-, mono-C8-10-alkyl ethers, phosphates | Non-Active substance | 68130-47-2 | 14,625 % (w/w) | |
| Alkylpolyglycoside C8-C10 | (3R,4S,5S,6R)-2-decoxy-6-(hydroxymethyl)oxane-3,4,5-triol | Non-Active substance | 68515-73-1 | 500-220-1 | 6,35 % (w/w) |
| Alcohols, C10-C16 ethoxylated propoxylated (Dehydol 980) | Alcohols, C10-C16 ethoxylated propoxylated | Non-Active substance | 69227-22-1 | 3 % (w/w) |
1. Meta spc 10 administrative information
1.1. Meta SPC 10 identifier
| Identifier | Meta SPC: META SPC 10 |
1.2. Suffix to the authorisation number
| Number | 1-10 |
1.3. Product type(s)
| Product type(s) | PT01: Human hygiene |
2. Meta spc 10 composition
2.1. Qualitative and quantitative information on the composition of the meta SPC 10
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
|---|---|---|---|---|---|
| Hydrogen peroxide | Active substance | 7722-84-1 | 231-765-0 | 1,4 - 1,61 % (w/w) | |
| Citric acid monohydrate | 2-hydroxypropane -1,2,3-tricarboxylic acid | Non-Active substance | 5949-29-1 | 201-069-1 | 0,9 - 0,9 % (w/w) |
| Phenoxyethanol | 2-Phenoxyethanol | Non-Active substance | 122-99-6 | 204-589-7 | 0,9 - 0,9 % (w/w) |
| Sodium lauryl Sulphate | Sodium dodecyl sulphate | Non-Active substance | 151-21-3 | 205-788-1 | 3,88 - 3,88 % (w/w) |
| L-Glutamic acid, N-coco acyl derivs., monosodium salts | Sodium;(4S)-4-amino-5-hydroxy-5-oxopentanoate | Non-Active substance | 68187-32-6 | 269-087-2 | 2 - 2 % (w/w) |
| Sulfuric acid, mono-C12-14-alkyl esters, ammonium salts (Texapon ALS) | Sulfuric acid, mono-C12-14-alkyl esters, ammonium salts | Non-Active substance | 90583-11-2 | 292-209-0 | 1,12 - 1,12 % (w/w) |
2.2. Type(s) of formulation of the meta SPC 10
| Formulation type(s) | AL Any other liquid |
3. Hazard and precautionary statements of the meta spc 10
| Hazard statements | H290: May be corrosive to metals.H319: Causes serious eye irritation. |
| Precautionary statements | P234: Keep only in original packaging.P264: Wash hands thoroughly after handling.P280: Wear eye protection.P280: Wear face protection.P390: Absorb spillage to prevent material damage.P406: Store in a a corrosion-resistant container with a resistant inner liner.P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.P337+P313: If eye irritation persists: Get medical attention.P337+P313: If eye irritation persists: Get medical advice. |
4. Authorised use(s) of the meta spc
4.1. Use description
| Product type | PT01: Human hygiene |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Direct application onto skinDetailed description:Antimicrobial hand soap, intended only as hygienic hand wash for food and beverage industry.Contact time at 20oC in dirty conditions:60 seconds for bacteria and yeasts. |
| Application rate(s) and frequency | Application rate:Application rate: 3 ml of product per applicationDilution (%):RTU productNumber and timing of application:Application frequency: 1-10 times/day |
| Category(ies) of users | professional |
| Pack sizes and packaging material | Light precluding HDPE Jug, 1-100 LLight precluding HDPE Jerry can, 1-100 LLight precluding HDPE IBC, 600-1000 LLight precluding HDPE Drum, 60-220 LLight precluding HDPE Bottle, 0,1-5 LLight precluding HDPE Pouch, 0,5-100 L |
4.1.1. Use-specific instructions
See general directions for use of meta SPC 10.
4.1.2. Use-specific risk mitigation measures
See general directions for use of meta SPC 10.
4.1.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 10.
4.1.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 10.
4.1.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 10.
5. General directions for use of the meta spc 10
5.1. Instructions for use
Apply approximately 3 ml of product to wet hands and rub for 60 seconds. Rinse thoroughly with running tap water for about 30 seconds.
5.2. Risk mitigation measures
Avoid splashes and spills.
Avoid hand to eye transfer.
5.3. Particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
FIRST AID MEASURES
In case of eye contact: Rinse with water.
In case of skin contact: Rinse with water.
If swallowed: Rinse mouth. Seek medical attention if symptoms occur.
If inhaled: Seek medical attention if symptoms occur.
ENVIRONMENTAL EMERGENCY MEASURES
Do not allow contact with soil, surface or ground water.
Consider the provision of containment around storage vessels.
5.4. Instructions for safe disposal of the product and its packaging
Product: Where possible, recycling is preferred to disposal or incineration. If recycling is not practicable, dispose of in compliance with national regulations. Dispose of waste in an approved waste disposal facility.
Contaminated packaging: Dispose of container in accordance with national regulations.
5.5. Conditions of storage and shelf-life of the product under normal conditions of storage
Keep out of reach of children. Keep container tightly closed. Store in suitable, labelled containers.
Storage temperature: 0-25°C
Shelf life: 18 months
6. Other information
The product contains hydrogen peroxide (CAS No.: 7722-84-1), for which a European reference value of 1,25 mg/m3 for the professional user was agreed and used for the risk assessment of the product.
7. Third information level: individual products in the meta spc 10
7.1. Trade name(s), authorisation number and specific composition of each individual product
| Trade name(s) | Manosan Oxy | Market area: EU | |||
| Authorisation number | EU-0024303-0013 1-10 | ||||
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| Hydrogen peroxide | Active substance | 7722-84-1 | 231-765-0 | 1,4 % (w/w) | |
| Citric acid monohydrate | 2-hydroxypropane -1,2,3-tricarboxylic acid | Non-Active substance | 5949-29-1 | 201-069-1 | 0,9 % (w/w) |
| Phenoxyethanol | 2-Phenoxyethanol | Non-Active substance | 122-99-6 | 204-589-7 | 0,9 % (w/w) |
| Sodium lauryl Sulphate | Sodium dodecyl sulphate | Non-Active substance | 151-21-3 | 205-788-1 | 3,88 % (w/w) |
| L-Glutamic acid, N-coco acyl derivs., monosodium salts | Sodium;(4S)-4-amino-5-hydroxy-5-oxopentanoate | Non-Active substance | 68187-32-6 | 269-087-2 | 2 % (w/w) |
| Sulfuric acid, mono-C12-14-alkyl esters, ammonium salts (Texapon ALS) | Sulfuric acid, mono-C12-14-alkyl esters, ammonium salts | Non-Active substance | 90583-11-2 | 292-209-0 | 1,12 % (w/w) |
1. Meta spc 11 administrative information
1.1. Meta SPC 11 identifier
| Identifier | Meta SPC: META SPC 11 |
1.2. Suffix to the authorisation number
| Number | 1-11 |
1.3. Product type(s)
| Product type(s) | PT02: Disinfectants and algaecides not intended for direct application to humans or animalsPT04: Food and feed area |
2. Meta spc 11 composition
2.1. Qualitative and quantitative information on the composition of the meta SPC 11
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
|---|---|---|---|---|---|
| Hydrogen peroxide | active substance | 7722-84-1 | 231-765-0 | 1,5 - 1,5 % (w/w) |
2.2. Type(s) of formulation of the meta SPC 11
| Formulation type(s) | AL Any other liquid |
3. Hazard and precautionary statements of the meta spc 11
| Hazard statements | |
| Precautionary statements |
4. Authorised use(s) of the meta spc
4.1. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: VirusesCommon name: VirusesDevelopment stage: no dataScientific name: Bacterial sporesCommon name: Bacterial sporesDevelopment stage: no dataScientific name: Clostridium difficileCommon name: Bacterial sporesDevelopment stage: no dataScientific name: MycobacteriaCommon name: MycobacteriaDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Wiping using impregnated RTU wipesDetailed description:Disinfection of small surfaces, materials and equipment in life sciences cleanrooms and supporting environments (e.g. pharmaceutical industry) and transfer disinfection.Contact times for wiping at 20oC in dirty conditions:5 minutes for bacteria, yeasts, fungi and mycobacteria;30 minutes for viruses;60 minutes for bacterial spores.Contact times for wiping at 20oC in clean conditions:5 minutes for Clostridium difficile spores;30 minutes for bacterial spores. |
| Application rate(s) and frequency | Application rate:Application rate: 1 wipe per m2 (corresponding to 10 ml/m2)Dilution (%):RTU productNumber and timing of application:Application frequency: up to twice per day per room |
| Category(ies) of users | professional |
| Pack sizes and packaging material | Light precluding PET or PE Bucket with 10-5000 impregnated 45% polyester / 55% cellulose blend wipes (wipe size: 420x250 mm or 200x200 mm).Light precluding PET/PE or EVA/PP or Aluminum/PE Pouch or PE Pouch with 10-100 impregnated 45% polyester / 55% cellulose blend wipes (wipe size: 420x250 mm or 200x200 mm) |
4.1.1. Use-specific instructions
See general directions for use of meta SPC 11.
4.1.2. Use-specific risk mitigation measures
-
4.1.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 11.
4.1.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 11.
4.1.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 11.
4.2. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: VirusesCommon name: VirusesDevelopment stage: no dataScientific name: Bacterial sporesCommon name: Bacterial sporesDevelopment stage: no dataScientific name: Clostridium difficileCommon name: Bacterial sporesDevelopment stage: no dataScientific name: MycobacteriaCommon name: MycobacteriaDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Mopping using impregnated RTU mop wipesDetailed description:Disinfection of floors in life sciences cleanrooms and supporting environments (e.g. pharmaceutical industry).Contact times for wiping at 20oC in dirty conditions:5 minutes for bacteria, yeasts, fungi and mycobacteria;30 minutes for viruses;60 minutes for bacterial spores.Contact times for wiping at 20oC in clean conditions:5 minutes for Clostridium difficile spores;30 minutes for bacterial spores. |
| Application rate(s) and frequency | Application rate: 1 wipe per m2 (corresponding to 10 ml/m2)Dilution (%):RTU productNumber and timing of application:Application frequency: up to twice per day per room |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Light precluding PET or PE Bucket with 10-5000 impregnated 45% polyester / 55% cellulose blend wipes (wipe size: 420x250 mm or 200x200 mm)Light precluding PET/PE or EVA/PP or Aluminum/PE Pouch or PE Pouch with 10-100 impregnated 45% polyester / 55% cellulose blend wipes (wipe size: 420x250 mm or 200x200 mm) |
4.2.1. Use-specific instructions
See general directions for use of meta SPC 11.
4.2.2. Use-specific risk mitigation measures
-
4.2.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 11.
4.2.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 11.
4.2.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 11.
4.3. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: No dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: MycobacteriaCommon name: MycobacteriaDevelopment stage: no dataScientific name: Bacterial sporesCommon name: Bacterial sporesDevelopment stage: no dataScientific name: Clostridium difficileCommon name: Bacterial sporesDevelopment stage: no dataScientific name: VirusesCommon name: VirusesDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Wiping using impregnated RTU wipesDetailed description:Routine disinfection of smaller surfaces in hospital rooms and medical practices that are not frequently touched by people.Contact times for wiping at 20oC in clean conditions:15 minutes for Clostridium difficile;30 minutes for bacterial spores, mycobacteria and viruses.Contact times for wiping at 20oC in dirty conditions:15 minutes for bacteria and yeasts;30 minutes for fungi, mycobacteria and viruses. |
| Application rate(s) and frequency | Application rate: 1 wipe per m2 (corresponding to 10 ml/m2)Dilution (%):RTU productNumber and timing of application:Application frequency: up to twice per day per room |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Light precluding pre-printed pouch with 10-100 impregnated 60% polyester / 40% lyocell blend wipes (wipe size: 420x250 mm or 200x200 mm).Light precluding PET canister with 10-1000 impregnated 60% polyester / 40% lyocell blend wipes (wipe size: 420x250 mm or 200x200 mm).Light precluding PET bucket with 10-1000 impregnated 60% polyester / 40% lyocell blend wipes (wipe size: 420x250 mm or 200x200 mm).Light precluding PET pouch with 10-1000 impregnated 60% polyester / 40% lyocell blend wipes (wipe size: 420x250 mm or 200x200 mm). |
4.3.1. Use-specific instructions
Routine disinfection: Disinfection of surfaces, which might be contaminated with pathogens during medical or nursing processes, on a regular basis to reduce the risk of transmission of such organisms via surfaces.
4.3.2. Use-specific risk mitigation measures
-
4.3.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 11.
4.3.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 11.
4.3.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 11.
4.4. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: No dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: MycobacteriaCommon name: MycobacteriaDevelopment stage: no dataScientific name: Bacterial sporesCommon name: Bacterial sporesDevelopment stage: no dataScientific name: Clostridium difficileCommon name: Bacterial sporesDevelopment stage: no dataScientific name: VirusesCommon name: VirusesDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Wiping using impregnated RTU wipesDetailed description:Routine disinfection of small surfaces in small non-food areas (e.g. bathrooms).Contact times for wiping at 20oC in clean conditions:15 minutes for Clostridium difficile spores;30 minutes for bacterial spores, mycobacteria and viruses.Contact times for wiping at 20oC in dirty conditions:2 minutes for bacteria;15 minutes for yeasts;30 minutes for fungi, mycobacteria and viruses. |
| Application rate(s) and frequency | Application rate:Application rate: 1 wipe per m2 (corresponding to 10 ml/m2)Dilution (%):RTU productNumber and timing of application:Application frequency: up to 10 times per day per room |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Light precluding pre-printed pouch with 10-100 impregnated 60% polyester / 40% lyocell blend wipes (wipe size: 420x250 mm or 200x200 mm).Light precluding PET canister with 10-1000 impregnated 60% polyester / 40% lyocell blend wipes (wipe size: 420x250 mm or 200x200 mm).Light precluding PET bucket with 10-1000 impregnated 60% polyester / 40% lyocell blend wipes (wipe size: 420x250 mm or 200x200 mm).Light precluding PET pouch with 10-1000 impregnated 60% polyester / 40% lyocell blend wipes (wipe size: 420x250 mm or 200x200 mm). |
4.4.1. Use-specific instructions
See general directions for use of meta SPC 11.
4.4.2. Use-specific risk mitigation measures
-
4.4.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 11.
4.4.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 11.
4.4.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 11.
4.5. Use description
| Product type | PT04: Food and feed area |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: No dataScientific name: FungiCommon name: fungiDevelopment stage: no dataScientific name: MycobacteriaCommon name: MycobacteriaDevelopment stage: no dataScientific name: Bacterial sporesCommon name: Bacterial sporesDevelopment stage: no dataScientific name: Clostridium difficileCommon name: Bacterial sporesDevelopment stage: no dataScientific name: VirusesCommon name: VirusesDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Wiping using impregnated RTU wipesDetailed description:Routine disinfection of small surfaces in small food areas (e.g. kitchens).Contact times for wiping at 20oC in clean conditions:15 minutes for Clostridium difficile spores;30 minutes for bacterial spores, mycobacteria and viruses.Contact time for wiping at 20oC in dirty conditions:2 minutes for bacteria;15 minutes for yeasts;30 minutes for fungi, mycobacteria and viruses. |
| Application rate(s) and frequency | Application rate:Application rate: 1 wipe per m2 (corresponding to 10 ml/m2)Dilution (%):RTU productNumber and timing of application:Application frequency: up to 10 times per day per room |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Light precluding pre-printed pouch with 10-100 impregnated 60% polyester / 40% lyocell blend wipes (wipe size: 420x250 mm or 200x200 mm).Light precluding PET canister with 10-1000 impregnated 60% polyester / 40% lyocell blend wipes (wipe size: 420x250 mm or 200x200 mm).Light precluding PET bucket with 10-1000 impregnated 60% polyester / 40% lyocell blend wipes (wipe size: 420x250 mm or 200x200 mm).Light precluding PET pouch with 10-1000 impregnated 60% polyester / 40% lyocell blend wipes (wipe size: 420x250 mm or 200x200 mm). |
4.5.1. Use-specific instructions
See general directions for use of meta SPC 11.
4.5.2. Use-specific risk mitigation measures
Keep food, feed or beverages away from treated surface until dried. Do not use directly on or near food, feed or drinks.
4.5.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 11.
4.5.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 11.
4.5.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 11.
5. General directions for use of the meta spc 11
5.1. Instructions for use
The product is intended for one-step cleaning and disinfection. Always read the label or leaflet before use and follow all the instructions. When used under clean conditions: clean surface before applying the product. Apply product to a dry surface. Wet surface completely using the product. Allow surface to air dry. Do not rinse after use. Close container when not in use. Do not use wipes which have become dehydrated. Dispose of the container when empty. Do not use on surfaces sensitive to oxidative agents such as marble, copper or brass. Used wipes must be disposed of in a closed container.
5.2. Risk mitigation measures
-
5.3. Particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
FIRST AID MEASURES
In case of eye contact: Rinse with plenty of water.
In case of skin contact: Rinse with plenty of water.
If swallowed: Rinse mouth. Seek medical attention if symptoms occur.
If inhaled: Seek medical attention if symptoms occur.
ENVIRONMENTAL EMERGENCY MEASURES
Do not allow contact with soil, surface or ground water.
Consider the provision of containment around storage vessels.
5.4. Instructions for safe disposal of the product and its packaging
Product: Where possible, recycling is preferred to disposal or incineration. If recycling is not practicable, dispose of in compliance with national regulations. Dispose of waste in an approved waste disposal facility.
Contaminated packaging: Dispose of container in accordance with national regulations.
5.5. Conditions of storage and shelf-life of the product under normal conditions of storage
Keep out of reach of children. Keep container tightly closed. Store in suitable, labelled containers.
Storage temperature: 0-35 °C. Protect from frost.
Shelf life: 18 months
6. Other information
The product contains hydrogen peroxide (CAS No.: 7722-84-1), for which a European reference value of 1,25 mg/m3 for the professional user was agreed and used for the risk assessment of the product.
7. Third information level: individual products in the meta spc 11
7.1. Trade name(s), authorisation number and specific composition of each individual product
| Trade name(s) | Klerwipe Sporicidal Enhanced Peroxide | Market area: EU | |||
| Anios Low Peroxide IP sterile wipes | Market area: EU | ||||
| Authorisation number | EU-0024303-0014 1-11 | ||||
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| Hydrogen peroxide | active substance | 7722-84-1 | 231-765-0 | 1,5 % (w/w) |
7.2. Trade name(s), authorisation number and specific composition of each individual product
| Trade name(s) | Incidin OxyWipe S | Market area: EU | |||
| KitchenPro Oxy Wipes S | Market area: EU | ||||
| Sirafan Oxy Wipes | Market area: EU | ||||
| Authorisation number | EU-0024303-0015 1-11 | ||||
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| Hydrogen peroxide | Active substance | 7722-84-1 | 231-765-0 | 1,5 % (w/w) |
1. Meta spc 12 administrative information
1.1. Meta SPC 12 identifier
| Identifier | Meta SPC: META SPC 12 |
1.2. Suffix to the authorisation number
| Number | 1-12 |
1.3. Product type(s)
| Product type(s) | PT02: Disinfectants and algaecides not intended for direct application to humans or animalsPT04: Food and feed area |
2. Meta spc 12 composition
2.1. Qualitative and quantitative information on the composition of the meta SPC 12
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
|---|---|---|---|---|---|
| Hydrogen peroxide | active substance | 7722-84-1 | 231-765-0 | 2 - 2,3 % (w/w) | |
| N-propanol | Propan-1-ol | Non-Active substance | 71-23-8 | 200-746-9 | 17,5 - 17,5 % (w/w) |
2.2. Type(s) of formulation of the meta SPC 12
| Formulation type(s) | AL Any other liquid |
3. Hazard and precautionary statements of the meta spc 12
| Hazard statements | H226: Flammable liquid and vapour.H318: Causes serious eye damage. |
| Precautionary statements | P210: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.P233: Keep container tightly closed.P240: Ground and bond container and receiving equipment.P241: Use explosion-proof electrical equipment.P241: Use explosion-proof ventilating equipment.P241: Use explosion-proof lighting equipment.P242: Use non-sparking tools.P243: Take actions to prevent static discharges.P280: Wear eye protection.P280: Wear face protection.P303+P361+P353: IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water [or shower].P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.P310: Immediately call a POISON CENTER.P310: Immediately call a doctor.P370+P378: In case of fire: Use water to extinguish.P403+P235: Store in a well-ventilated place. Keep cool.P501: Dispose of contents to in accordance with national regulations.P501: Dispose of container to in accordance with national regulations. |
4. Authorised use(s) of the meta spc
4.1. Use description
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Wiping using impregnated RTU wipesDetailed description:Disinfection of surfaces in industry (e.g. dining areas, bathrooms).Contact time for wiping at 10oC and 20oC in dirty conditions:5 minutes for bacteria and yeasts. |
| Application rate(s) and frequency | Application rate:Application rate: 1 wipe per m2 (corresponding to 10 ml/m2)Dilution (%):RTU productNumber and timing of application:Application frequency: up to 3 times per day |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Light precluding PP Bucket with 10-5000 impregnated non-woven, 100% polypropylene wipes (wipe size: 200x250 mm).Light precluding PE Pouch with 10-5000 impregnated non-woven, 100% polypropylene wipes (wipe size: 200x250 mm). |
4.1.1. Use-specific instructions
See general directions for use of meta SPC 12.
4.1.2. Use-specific risk mitigation measures
See general directions for use of meta SPC 12.
4.1.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 12.
4.1.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 12.
4.1.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 12.
4.2. Use description
| Product type | PT04: Food and feed area |
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: BacteriaCommon name: BacteriaDevelopment stage: no dataScientific name: YeastsCommon name: YeastsDevelopment stage: no data |
| Field(s) of use | indoor use |
| Application method(s) | Method: Wiping using impregnated RTU wipesDetailed description:Disinfection of small surfaces in food processing plants.Contact time for wiping at 10oC and 20oC in dirty conditions:5 minutes for bacteria and yeasts. |
| Application rate(s) and frequency | Application rate:Application rate: 1 wipe per m2 (corresponding to 10 ml/m2)Dilution (%):RTU productNumber and timing of application:Application frequency: up to 4 times per day |
| Category(ies) of users | professional |
| Pack sizes and packaging material | Light precluding PP Bucket with 10-5000 impregnated non-woven, 100% polypropylene wipes (wipe size: 200x250 mm).Light precluding PE Pouch with 10-5000 impregnated non-woven, 100% polypropylene wipes (wipe size: 200x250 mm). |
4.2.1. Use-specific instructions
See general directions for use of meta SPC 12.
4.2.2. Use-specific risk mitigation measures
Keep food, feed or beverages away from treated surface until dried. Do not use directly on or near food, feed or drinks.
4.2.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use of meta SPC 12.
4.2.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use of meta SPC 12.
4.2.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use of meta SPC 12.
5. General directions for use of the meta spc 12
5.1. Instructions for use
Always read the label or leaflet before use and follow all the instructions. The product should be applied to a dry surface. Wet surface completely using the product. Allow surface to air dry after using the product. Do not rinse after use. Close container when not in use. Do not use wipes which have become dehydrated. Dispose of the container when empty. Do not use on surfaces sensitive to oxidative agents such as marble, copper or brass. Used wipes must be disposed of in closed container.
5.2. Risk mitigation measures
Avoid hand to eye transfer.
5.3. Particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
FIRST AID MEASURES
In case of eye contact: Rinse immediately with plenty of water, including under the eyelids, for at least 15 minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Seek medical attention immediately.
In case of skin contact: Rinse with plenty of water.
If swallowed: Rinse mouth. Seek medical attention if symptoms occur.
If inhaled: Remove person to fresh air. Treat symptomatically. Seek medical attention if symptoms occur.
ENVIRONMENTAL EMERGENCY MEASURES
Do not allow contact with soil, surface or ground water.
Consider the provision of containment around storage vessels
5.4. Instructions for safe disposal of the product and its packaging
Product: Where possible, recycling is preferred to disposal or incineration. If recycling is not practicable, dispose of in compliance with national regulations. Dispose of waste in an approved waste disposal facility.
Contaminated packaging: Dispose of container in accordance with national regulations.
5.5. Conditions of storage and shelf-life of the product under normal conditions of storage
Keep out of reach of children. Keep container tightly closed. Store in suitable, labelled containers. Keep away from heat and sources of ignition. Keep in a cool, well-ventilated place. Keep away from oxidizing agents.
Storage temperature: 0-30°C.
Shelf life: 12 months
6. Other information
The product contains hydrogen peroxide (CAS No.: 7722-84-1), for which a European reference value of 1,25 mg/m3 for the professional user was agreed and used for the risk assessment of the product.
7. Third information level: individual products in the meta spc 12
7.1. Trade name(s), authorisation number and specific composition of each individual product
| Trade name(s) | OxyDes Maxi Wipes | Market area: EU | |||
| Authorisation number | EU-0024303-0016 1-12 | ||||
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| Hydrogen peroxide | Active substance | 7722-84-1 | 231-765-0 | 2 % (w/w) | |
| N-propanol | Propan-1-ol | Non-Active substance | 71-23-8 | 200-746-9 | 17,5 % (w/w) |
Source: EUR-Lex, © European Union, 1998-2026. Reuse authorised under Decision 2011/833/EU.