Council Regulation (EU) 2025/1303

Contents

THE COUNCIL OF THE EUROPEAN UNION,Having regard to the Treaty on the Functioning of the European Union, and in particular Article 31 thereof,Having regard to the proposal from the European Commission,Whereas:

(1)In order to ensure a sufficient supply of certain agricultural and industrial products which are not produced in the Union and thereby avoid any disturbances on the market for those products, Common Customs Tariff duties of the type referred to in Article 56(2), point (c), of Regulation (EU) No 952/2013 of the European Parliament and of the Council^note (‘CCT duties’) on those products have been suspended by Council Regulation (EU) 2021/2278^note. As a result, the products listed in the Annex to Regulation (EU) 2021/2278 can be imported into the Union at reduced or zero duty rates without any limitation as regards their quantity.

(2)The Union production of certain products that are not listed in the Annex to Regulation (EU) 2021/2278 is inadequate to meet the specific requirements of the user industries in the Union. As it is in the interest of the Union to ensure an adequate supply of products meeting those requirements, and having regard to the fact that identical, equivalent or substitute products are not produced in sufficient quantities within the Union, it is necessary to grant a complete suspension of the CCT duties on such products.

(3)It is necessary to amend the product description, classification, or end-use requirement for certain products listed in the Annex to Regulation (EU) 2021/2278 in order to take into account technical product developments and economic trends in the market.

(4)The Commission has reviewed in accordance with Article 2(2) of Regulation (EU) 2021/2278 certain CCT duty suspensions for products listed in the Annex to that Regulation. As it is in the interest of the Union to maintain the CCT duty suspensions for some of those products, new dates should be set for their next mandatory review.

(5)It is no longer in the interest of the Union to maintain the suspension of CCT duties for certain products listed in the Annex to Regulation (EU) 2021/2278. The suspensions for those products should therefore be deleted with effect from 1 July 2025.

(6)In response to the Russian Federation’s ongoing war of agression against Ukraine and the continued involvement of Belarus in actions undermining Ukraine’s sovereignty and territorial integrity, the Union has adopted restrictive measures to limit trade benefits granted to Russia and Belarus. However, Council Regulation (EU) 2022/2583^note retained the suspension of CCT duties for certain products originating in Belarus falling under TARIC code 2926907024 and for certain products originating in Russia falling under TARIC codes 7608208930 and 8401300020. Given the continuing geopolitical instability and the need to reinforce the effectiveness of the Union’s restrictive measures, to ensure consistency with the objectives of the Union’s trade policy and to prevent economic advantages from being conferred upon entities supporting actions contrary to international law, it is appropriate to discontinue those exceptions for products originating in Belarus falling under TARIC code 2926907024 and for products originating in Russia falling under TARIC code 7608208930, and to reinstate the application of CCT duties on imports of those products originating in Russia and Belarus.

(7)Regulation (EU) 2021/2278 should therefore be amended accordingly.

(8)In order to avoid any interruption in the application of the autonomous tariff suspension scheme and to comply with the guidelines set out in the communication from the Commission of 13 December 2011 concerning autonomous tariff suspensions and quotas, the changes provided for in this Regulation regarding the tariff suspensions for the products concerned should apply from 1 July 2025. This Regulation should therefore enter into force as a matter of urgency,

HAS ADOPTED THIS REGULATION:

Article 1 #

Regulation (EU) 2021/2278 is amended as follows:

(1)in Article 1, paragraph 2 is replaced by the following:‘2.Paragraph 1 does not apply to any of the following:

(a)any mixtures, preparations, or products made up of different components containing products as listed in the Annex;

(b)products originating in Belarus;

(c)products originating in Russia, with the exception of products falling under TARIC code 8401300020.’

;

(2)the Annex is amended in accordance with the Annex to this Regulation.

Article 2 #

This Regulation shall enter into force on the day following that of its publication in the Official Journal of the European Union.It shall apply from 1 July 2025.

The Annex to Regulation (EU) 2021/2278 is amended as follows:

(1)the entries with the following serial numbers are deleted: 0.3046, 0.5139, 0.8443, 0.8679;

(2)the following entries replace those entries that have the same serial numbers:^noteSerial NumberCN codeTARICDescriptionRate of autonomous dutySupplementary UnitDate envisaged for mandatory review‘0.4080ex1517909930Vegetable and/or microbial oil, refined, containing by weight:

—25 % or more but not more than 70 % arachidonic acid and no more than 5 % docosahexenoic acid, or

—whether or not with pulley or coupling,

—whether or not with rotor position sensor

—with a weight of 5,2 kg or more, but not more than 12,5 kg

—whether or not with rotor position sensor

—a dilution steam generator system which produces steam from pretreated quench water for use as dilution steam in steam cracking furnaces,

—quench water circulation loops, which contain a heat exchanger and circulation pumps to cool and recirculate quench water,

—an open loop ethylene refrigeration system, which is to be integrated with an external ethylene refrigerant compressor,

—coolers,

—caustic water circulation pumps to support an external caustic wash tower in removing acid gasses (carbon dioxide and hydrogen sulphide) from the cracked gas,

—various distillation columns (depropanizer, debutanizer and degreenoiler) and their associated heat exchangers, pumps and drums,

—a system for filtering and cooling of dried cracked gas,

—a rated torque of 25 Nm or more, but not more than 70 Nm,

—a specified speed of not more than 6000 rpm,

—a specified speed of not more than 7000 rpm,

—80 % or more but not more than 90 % of docusate sodium (INN) (CAS RN 577-11-7), and

—of EN AC-47100 aluminum,

—of EN AC-47100-F aluminum,

—of EN AC-47100 aluminum,

—a length of 670 mm or more, but not more than 882 mm,

—a lithium-ion battery with a voltage of 36 V or more but not more than 50,4 V and a nominal energy between 0,3 kWh and 0,9 kWh,

—bis[2,2,6,6-tetramethyl-1-(octyloxy)piperidin-4-yl] decanedioate, and

—branched and linear C7 to C9 alkyl esters of [3-(2H-benzotriazol-2-yl)-5-(1,1-dimethylethyl)-4-hydroxy]-1-phenylpropanoic acid (CAS RN 127519-17-9) with a content by weight of 85 % or more, and

—56 % or more but not more than 85 % of divinylbenzene isomers (CAS RN 1321-74-0)

—65 % or more but not more than 75 % of C12 FAME,

—50 % or more but not more than 58 % of C8-FAME

—coated with diamond grains of 5μm or more, but not more than 55μm

—parts of common metal, and

—10 % or more but not more than 80 % of eicosapentaenoic acid and a minimum ratio of EPA/(EPA+DHA) over 20 %,

—a condensate system that collects, filters and deaerates steam condensates, which are subsequently recycled as boiler feed water and further distributed within the cracker unit, and

—a water purification system, which removes hydrocarbon contaminants from quench water which is then re-used for dilution steam production (outside the module),

—pumps and a heat exchanger to deliver ethylene to an external pipeline, and

—vapor-liquid separation drums, and

—a spent caustic pre-treatment system, containing separation drums, pumps and mixers,

—a chilling train containing heat exchangers and a drum which condenses C2 in a gas stream,

—a deethanizer distillation column and associated equipment for C2-/C3+ separation,

—standard gear ratios of 1:12,7 or more, but not more than 1:65,3

—a minimum output of 400 W, but not more than 1,3 kW (at 12 V), or with a minimum output of 750 W but not more than 1,55 kW (at 36 V),

—an output of 400 W or more but not more than 750 W (at 12 V),

—10 % or more but not more than 20 % of sodium benzoate (CAS RN 532-32-1)

—shot-blasted and machined,

—with a sealing cap of stainless steel,

—with or without overmolded bearing sleeves of martensitic stainless steel and assembled sealing caps of stainless steel,

—a width of 390 mm or more, but not more than 655 mm,

—a Battery Management System,

—1,1′-bis[2,2,6,6-tetramethyl-1-(octyloxy)piperidin-4-yl] 10,10′-{octane-1,8-diylbis[oxy(2,2,6,6- tetramethylpiperidine-1,4-diyl)]} didecanedioate

—2-Methoxy-1-methylethyl acetate (CAS RN 108-65-6) with a content by weight of not more than 8 %

—15 % or more but not more than 44 % of ethylvinylbenzene isomers (CAS RN 28106-30-1)

—21 % or more but not more than 28 % of C14 FAME,

—35 % or more but not more than 50 % of C10-FAME

—wire diameter 23 μm or more but not more than 350 μm,

—whether or not comprising parts of plastic,

—4 % or more but not more than 8 % of C16 FAME,

—an acetylene hydrogenation system to remove acetylene within a C2 stream,

—a flange diameter of 85 mm or more but not more than 200 mm,

—a flange diameter of 80 mm or more, but not more than 200 mm,

—leakproof to the degree of 3 ml per minute or less under 2,75 bar pressure,

—shot-blasted and machined,

—a height of 110 mm or more, but not more than 137 mm,

—a power relay,

—having a breaking strength of 11 N or more, but not more than 170 N

—epoxy resin reinforced with fiberglass or wood,

—a flare system that collects, separates and vaporizes non-recyclable hydrocarbon containing releases from different equipment in a steam cracker, and transfers those towards flares

—a pyrolysis oil purification system, which separates pyrolysis gasoline, heavy oil and coke fractions from the hydrocarbon contaminants that have been removed from the quench water,

—a closed loop propylene refrigeration system, which is to be integrated with an external propylene refrigerant compressor

—pumps needed to condense and remove water and heavier hydrocarbons and to avoid undesirable formation of polymer by-products,

—a heat exchanger for the pre-cooling of cracked gas, and

—a system to separate hydrogen and methane from cracked gas containing heat exchangers, drums, turbines, compressors and a hydrogen purification unit (pressure swing adsorption unit),

—whether or not printed or surface-treated,

—with or without a rotor chamber, leakproof to the degree of 3 ml per minute or less under 2,75 bar pressure,

—a weight of 60 kg or more, but not more than 165 kg, and

—a cooling system,

—an ethane feedstock start-up vaporizer and superheater, which vaporizes and heats ethane feedstock before sending the ethane to the cracking furnaces (outside the module),

—a separation drum for the removal of water from cracker gas

—associated equipment of a C3 splitter distillation column, containing heat exchanger, pumps and drums, and

—a fuel gas drum that stores fuel gas for cracker furnaces, and

—a maximum length of 335 mm, measured from the beginning of the shaft to the outer ending,

—a maximum length of not more than 335 mm, measured from the beginning of the shaft to its outer end,

—with a hardness of 70 or more on the Hardness Brinell Wolfram (HBW) scale (2,5/62,5, according to ISO 6506),

—leakproof to the degree of 1 ml per minute or less under 2,75 bar pressure,

—with or without electrical conductors,

—a power of 11300 Wh or more, but not more than 29360 Wh

—one to four connectors,

—a propane feedstock preparation system, which filters, vaporizes and superheats propane feedstock, before sending the propane to cracking furnaces (outside the module), and

—a vinyl acetylene hydrogenation system, containing hydrogenation reactors, filters, mixer, drum, condenser, heat exchangers

—a system to regenerate dryers in a cracker installation

—a housing length of not more than 265 mm, measured from the flange to the outer ending,

—a housing length of not more than 265 mm, measured from the flange to the outer end,

—with a tensile strength of 190 N/mm² or more,

—with a hardness of 70 HBW or more (2,5/62,5, according to ISO 6506),

—with a hardness of 70 or more on the Hardness Brinell Wolfram (HBW) scale (2,5/62,5, according to ISO 6506),

—with or without a membrane bonded to the keyboard,

—a chemical grade propylene preparation system, which filters and dries chemical grade propylene before sending it to the deethanizer (outside the module)

—a maximum of two-piece (basic housing including electric components and flange with minimum 2 and maximum 11 bore holes) aluminium diecast or sheet steel housing whether or not with a sealing compound (groove with an O-ring and grease),

—a steel sheet or die-cast aluminium basic housing consisting of not more than two parts, including electrical components and a flange with two or more but not more than 11 holes, whether or not with a sealing connection (groove with O-ring and protective grease or liquid seal interface),

—with a height of 160 mm or more, but not more than 330 mm,

—with a tensile strength of 190 N/mm² or more,

—with or without mono or multilayer protective film

—a stator with single T-tooth design and single coil windings in 9/6 or 12/8 or 12/10 topology, and

—a stator with single T-tooth design and single coil winding with 9/6 or 12/10 or 12/8 topology and surface magnets,

—with a diameter of 240 mm or more, but not more than 368 mm,

—with a height of 42 mm or more, but not more than 64 mm,

—with a height of 195 mm or more, but not more than 430 mm,

—surface magnets,

—whether or not with electronic power steering controller,

—with a weight of 3 kg or more, but not more than 5,84 kg

—with a diameter of 88 mm or more, but not more than 132 mm,

—with a width of 290 mm or more, but not more than 625 mm,

—whether or not with electronic power steering controller,

—whether or not with pulley or coupling,

—with a weight of 0,3 kg or more, but not more than 0,5 kg

—with a length of 270 mm or more, but not more than 535 mm,

standardized with vegetable oil0 %—31.12.20260.8441ex2841800020Disodium wolframate (CAS RN 13472-45-2) with a purity by weight of 90 % or more0 %—31.12.20270.3419ex2850002080Arsine (CAS RN 7784-42-1) with a purity by volume of 99,999 % or more, for use in the production of semiconductors^note0 %—31.12.20250.3848ex2907290085Phloroglucinol anhydrous (CAS RN 108-73-6) or phloroglucinol dihydrate (CAS RN 6099-90-7) with a purity by weight of 95 % or more0 %—31.12.20290.3682ex2909609040Bis(α,α-dimethylbenzyl) peroxide (CAS RN 80-43-3) with a purity by weight of 98 % or more2,8 %—31.12.20260.3480ex2914290075Bornan-2-one (CAS RN 76-22-2) with a purity by weight of 90 % or more0 %—31.12.20290.5909ex29153900332-tert-Butylcyclohexyl acetate (CAS RN 88-41-5) with a purity by weight of 98 % or more, containing by weight 80 % or more of cis-2-tert-butylcyclohexyl acetate (CAS RN 20298-69-5)0 %—31.12.20290.4742ex2918999067Allyl-(3-methylbutoxy)acetate (CAS RN 67634-00-8) with a purity by weight of 95 % or more0 %—31.12.20290.6004ex2920290025Fosetyl-aluminium (ISOM)(CAS RN 39148-24-8) with a purity by weight of 96 % or more0 %—31.12.20290.3526ex29251100301,2-benzisothiazol-3(2H)-one 1,1-dioxide (CAS RN 81-07-2) or sodium 1,2-benzothiazol-3-olate 1,1-dioxide (CAS RN 128-44-9) with a purity by weight of 98 % or more0 %—31.12.20290.3522ex2926907032Ethyl cyanoacetate (CAS RN 105-56-6) or methyl cyanoacetate (CAS RN 105-34-0) with a purity by weight of 97 % or more0 %—31.12.20290.2667ex29270000452,2′-Dimethyl-2,2′-azodipropionamidine dihydrochloride (CAS RN 2997-92-4) with a purity by weight of 97 % or more0 %—31.12.20290.2810ex29270000554′-Aminoazobenzene-4-sulphonic acid (CAS RN 104-23-4) with a purity by weight of 90 % or more0 %—31.12.20290.3492ex2931498020Tetrabutylphosphonium acetate (CAS RN 30345-49-4) in the form of an aqueous solution, containing by weight 40 % or more but not more than 50 % of tetrabutylphosphonium acetate0 %—31.12.20290.3990ex2932209080Gibberellic acid (CAS RN 77-06-5) with a purity by weight of 88 % or more, for use in the manufacture of plant protection products^note0 %—31.12.20290.2578ex2933599558Sitagliptin phosphate monohydrate (INNM) (CAS RN 654671-77-9) with a purity by weight of 95 % or more, and containing by weight not more than 1 % of a stabiliser0 %—31.12.20270.6569ex3204140010Colourant C.I. Direct Black 80 (CAS RN 8003-69-8) and preparations based thereon with a colourant C.I. Direct Black 80 content of 90 % or more by weight0 %—31.12.20290.3661ex3301121010Essential oil of sweet orange (CAS RN 8028-48-6) or essential oil of sour orange (CAS RN 72968-50-4), not deterpenated0 %—31.12.20290.3660ex3402901080Mixture, containing by weight:0 %—31.12.20290.6432ex3811290038Additives consisting of the C12-C14-tert-alkylamine salts of the esters of C14-C18 saturated and C18 unsaturated alcohols with phosphorus pentoxide (CAS RN 1471315-74-8), for use in the manufacture of blends of additives for lubricating oils or greases^note0 %—31.12.20290.6433ex3811290043Reaction products of C14-C18 (branched and linear) and C18 (unsaturated) fatty acids with tetraethylenepentamine (linear, branched, cyclic) (CAS RN 68784-17-8), for use in the manufacture of lubricating oils^note0 %—31.12.20290.6020ex3811290048Mixed C12-C20-alkyl and C14-C18-unsaturated alkyl derivates of phosphonic acid (CAS RN 93925-25-8), containing by weight more than 80 % of oleyl, palmityl and stearyl groups, for use in the manufacture of lubricating oils^note0 %—31.12.20290.3444ex3812399048UV stabilizer (CAS RN 129757-67-1), reaction mass containing by weight 97 % or more of:0 %—31.12.20290.8366ex3812399053Light stabilizer, containing by weight more than 90 % of reaction products of stearate methyl ester with 1-(2-hydroxy-2-methylpropoxy)-2,2,6,6-tetramethyl-4-piperidinol (CAS RN 300711-92-6)0 %—31.12.20270.8533ex3812399075UV stabilizer containing a mixture of:0 %—31.12.20280.4707ex3824999258Mixture containing by weight:0 %—31.12.20290.5939ex38260010ex38260010ex38260010ex3826001020212229Mixture of fatty acid methyl esters containing by weight at least:for use in the manufacture of detergents and home and personal care products^note0 %—31.12.20290.5941ex38260010ex38260010ex38260010ex3826001050515259Mixture of fatty acid methyl esters containing by weight at least:for the manufacturing of high purity C8 or C10 fatty acid or fatty acid mixtures thereof or of high purity methylester of C8 or C10 fatty acid^note0 %—31.12.20290.5473ex39039090ex391190996060Copolymer of styrene with maleic anhydride, either partially esterified or completely chemically modified, in flake or powder form0 %—31.12.20260.8666ex6804210040Steel wire used for cropping and squaring semiconductors:0 %—31.12.20280.5024ex83016000ex84199085ex84799070ex84819000ex84859090ex85030098ex85159080ex85371098ex85389099ex87089910ex870899973040305030434055705522Silicone or plastic keyboards, comprising:0 %p/st31.12.20250.8668ex8402900010Pre-assembled process module unit of an ethane cracker unit, containing:0 %—30.06.20260.8669ex8419400010Pre-assembled process module unit of an ethane cracker unit, containing:0 %—30.06.20260.8680ex8419508020Pre-assembled process module unit of an ethane cracker unit, containing:0 %—30.06.20260.8675ex8419899810Pre-assembled process module unit of an ethane cracker unit, containing:equipment associated with an external multi-stage, centrifugal cracked gas compressor which compresses hydrocarbon gases to allow further processing downstream in interconnected equipment containing:equipment associated with an external caustic wash tower containing:0 %—30.06.20260.8673ex8479899733Pre-assembled process module unit of an ethane cracker unit, containing:0 %—30.06.20260.8681ex8479899743Pre-assembled process module unit of an ethane cracker unit, containing:0 %—30.06.20260.5977ex8483402960Epicyclic gearing, of a kind used in driving hand-held power tools with:0 %p/st31.12.20290.6809ex85013100ex850132006365Ready for installation in vehicles or equipment of headings 8432 and 8433, brushless and permanently excited direct current motor with:0 %p/st31.12.20250.8590ex8501510045Automotive-ready brushless permanently excited magnet synchronous alternating current motor with:0 %p/st31.12.20280.8658ex8503009840Pressure casted inner housing of a cooling channel system for an electrical motor:0 %—31.12.20280.8662ex8503009853Pressure casted rotor cover of the cooling channel system in the electrical motor:0 %—31.12.20280.8659ex8503009863Pressure casted outer housing of an electrical motor:0 %—31.12.20280.8660ex8507600026Modules for the assembly of electric accumulators using lithium ferrophosphate technology (LFP) with:1,3 %p/st31.12.20250.8115ex8507600048Integrated battery system in a metal or plastic case with or without holders, consisting of:for use in the manufacture of Mild-hybrid (mHEV) motor vehicles^note1,3 %p/st31.12.2025

(3)the following entries are inserted according to the numerical order of the CN and TARIC codes in the second and third columns:^noteSerial NumberCN codeTARICDescriptionRate of autonomous dutySupplementary UnitDate envisaged for mandatory review‘0.8826ex2713200010Petroleum resin containing by weight

—more than 98 % of asphalt (CAS RN 8052-42-4) and

—a maximum temperature of motor operation of no more than 200 °C

—a friction torque in ambient temperature of no more than 23 mNm,

—whether or not with rotor position sensor

—a maximum temperature of motor operation of no more than 200 °C

—calcium carbonate (CAS RN 471-34-1),

—magnesium oxide (CAS RN 1309-48-8),

—55 % or more but not more than 65 % of (2S,3S,4S,5R,6R)-2-(((2R,3R,5S,6R)-4-(((2R,3S,4S,5R,6R)-3-acetoxy-4,5-bis(benzyloxy)-6-((benzyloxy)methyl)tetrahydro-2H-pyran-2-yl)oxy)-3,5-bis(benzyloxy)-6-(4-methoxy-4-oxobutoxy)tetrahydro-2H-pyran-2-yl)methoxy)-6-((((2S,3S,4S,5R,6R)-3-acetoxy-4,5-bis(benzyloxy)-6-((benzyloxy)methyl)tetrahydro-2H-pyran-2-yl)oxy)methyl)tetrahydro-2H-pyran-3,4,5-triyl tribenzoate (CAS RN 1233475-58-5),

—30 % or more, but not more than 60 % of 3a,4,4a,5,8,8a,9,9a-octahydro-4,9:5,8-dimethano-1H-benz[f]indene (CAS RN 7158-25-0),

—80 % or more, but not more than 90 % of 3a,4,7,7a-tetrahydro-4,7-methanoindene (CAS RN 77-73-6), and

—78 % or more but not more than 82 % of insoluble sulphur (CAS RN 9035-99-8),

—48 % of styrene,

—75 % or more of polyethyleneglycol modified butyl-2-cyano-3-(4-hydroxy-3-methoxyphenyl) acrylate, with an ethylene oxide chain length of not more than 30 (CAS RN 780763-40-8)

—a thickness of 0,229 mm or more but not more than 0,279 mm,

—a total thickness of 300 μm or more, but not more than 330 μm,

—in the form of powder,

—a light transmittance of 34,2 % or more but not more than 37,8 %,

—a glass wool filling,

—a glass fiber filling,

—an output of more than 40 MW but not more than 90 MW,

—with a weight of 45 kg or more but not more than 57 kg,

—with a weight of 827 kg or more but not more than 935 kg,

—with a power output of more than 0,4 kW but not exceeding 10 kW,

—of EN AC-46000 aluminium,

—measuring 403 x 276 x 70 mm or more, but not more than 464 x 399 x 83 mm,

—without an integrated carriage,

—25 % or more but not more than 40 % of Colourant C.I. Basic Blue 3 (CAS RN 33203-82-6) and

—with a cable of length of 550 mm or more but not more than 700 mm incorporating an electrical connector,

—high-pressure die-cast aluminium EN AC-46000,

—a length of 137,8 mm or more but not more than 138,2 mm,

—a three-phase winding,

—a rated voltage of 310 V,

—an output power of 550 W,

—an output power of 600 W,

—a specified speed of not more than 7000 rpm,

—an output power of 850 W,

—with or without operating components, signal components and display,

—48 % or more but not more than 55 % of antimony pentoxide (CAS RN 1314-60-9),

—with a length of 170 mm or more but not more than 301 mm,

—with a 26-PIN or 28-PIN wire to board connectors in crimping technology,

—double pinion type planetary gear shifting mechanism,

—cast aluminium body,

—with corrosion protection,

—an outer diameter of 81,2 mm or more, but not more than 82,55 mm,

—a torsional rigidity of 25 Nm/degree or more,

—an ultimate torsional strength load of 325 Nm or more and Johnson Apparent Elastic Limit (J.A.E.L.) values of 275 Nm or more,

—an ultimate torsional strength of 260 Nm or more,

—more than 97 % but not more than 99,8 % of bis(2,4-dicumylphenyl)pentaerythritol diphosphite (CAS RN 154862-43-8) and

—a shaft torsional stiffness of 2,5 Nm/degree or more but not more than 2,7 Nm/degree,

—an ultimate torsional strength of 300 Nm or more and Johnson Apparent Elastic Limit (J.A.E.L.) values of 275 Nm or more,

—a ball stud made of EN 10263/4 – 41CrS4 Q + T steel or AISI 4137 (SCM435) steel or EN10083/3-42CrMoS4Q + T steel or JIS G4053-SCM435 low alloy steel,

—reaction mass of Poly(oxy-1,2-ethanediyl),.alpha.-[3-[3-(2H-benzotriazol-2-yl)-5-(1,1-dimethylethyl)-4-hydroxyphenyl]-1-oxopropyl]-.omega.-hydroxy- and Poly(oxy-1,2-ethanediyl),.alpha.-[3-[3-(2H-benzotriazol-2-yl)-5-(1,1-dimethylethyl)-4-hydroxyphenyl]-1-oxopropyl]-.omega.-[3-[3-(2H-benzotriazol-2-yl)-5-(1,1-dimethylethyl)-4-hydroxyphenyl]-1-oxopropoxy] (EC number 400-830-7) with a purity by weight of 60 % or more, but not more than 80 %, and

—a mixture of branched and linear C7-C9 alkyl 3-[3-(2H-benzotriazol-2-yl)-5-(1,1-dimethylethyl)-4-hydroxyphenyl]propionates (CAS RN 127519-17-9) with a content by weight of 40 % or more, but not more than 60 %, and

—75 % or more but not more than 95 % of the reaction product of 2-(4,6-bis(2,4-dimethylphenyl)-1,3,5-triazin-2-yl)-5-hydroxyphenol with ((C10-16, rich in C12-13 alkyloxy) methyl) oxyrane

—more than 45 % but not more than 49 % of Octyl 3-[3-tert-butyl-4-hydroxy-5-(5-chloro-2H-benzotriazol-2-yl)phenyl]propionate (CAS RN 83044-89-7), and

—less than 2 % of hydrated amorphous silica (CAS RN 112926-00-8)

—copper oxide (CAS RN 1217-38-0),

—aluminium oxide (CAS RN 1344-28-1),

—35 % or more but not more than 45 % of toluene (CAS RN 108-88-3)

—10 % or more, but not more than 50 % of 3a,4,7,7a-tetrahydro-4,7-methanoindene (CAS RN 77-73-6), and

—not more than 10 % of 3a,4,4a,5,8,8a,9,9a-octahydro-1H-4,9:5,8-dimethanocyclopenta[b]naphtalene (CAS RN 7158-25-0), and

—18 % or more but not more than 22 % of naphthenic oil (CAS RN 64742-52-5), and

—22 % of acrylonitrile,

—not more than 25 % of ethoxylated sorbitan trioleate (CAS RN 9005-70-3)

—a titanium dioxide content by weight of 3 % or more but not more than 3,5 %,

—a tensile strength of 375 N/cm or more in both the longitudinal and transverse directions (ASTM D-882),

—of a purity by weight of 98 % or more,

—a diameter of 477,2 mm or more but not more than 477,8 mm,

—a thickness of 5,6 mm or more but not more than 32,4 mm,

—designed for a pressure of not more than 165 bar and a temperature of not more than 565 °C,

—with a diameter of 119 mm or more but not more than 149 mm,

—with a diameter of 250 mm or more but not more than 330 mm,

—shot-blasted and machined,

—with a total weight of a set of 236 g or more, but not more than 1010 g,

—suitable for machines with a load capacity of not more than 11000 kg,

—with an operating pressure of not more than 5,5 bar,

—25 % or more but not more than 40 % of C.I. Basic Blue 159 (CAS RN 105953-73-9)

—shot-blasted and machined,

—an outer diameter of 23 mm or more but not more than 48,025 mm,

—an output power not exceeding 280 W,

—a rated power of 350 W or more but not more than 368 W,

—a rotor containing 8 poles generated by permanent magnets composed mainly with neodymium-iron-boron (per GB/T 13560 standard) enclosed in polyethylene cover,

—a rotor containing 8 poles generated by permanent magnets composed mainly with neodymium-iron-boron and dysprosium enclosed in aluminium cover,

—an output of 750 W or more but not more than 1,8 kW (at 12 V),

—a rotor containing 8 poles generated by permanent magnets composed mainly with neodymium-iron-boron (per GB/T 13560 standard) enclosed in polyethylene cover,

—for operating voltages of 5V DC or more but not more than 12V DC or 220V AC or more but not more than 400V AC,

—with an external diameter of 4,5 mm or more but not more than 7 mm,

—1 % or more but not more than 5 % of triethanolamine (CAS RN 102-71-6)

—bound by rubber or vinyl or electrical tape or conduit or a weave of extruded string or a combination thereof,

—sport sequential shiftmatic system with a speed of 7 or more but not more than 10,

—differential gear,

—for pressures up to 150 PSI (1034 kPa),

—an inner diameter of 25,9 mm or more, but not more than 25,97 mm,

—a tubular male shaft in welded carbon steel tube (per GB/T 699 grade 20),

—a length of 66,39 mm or more but not more than 88,64 mm,

—a length of 165,3 mm or more but not more than 204,2 mm,

—a length of 296,7 mm or more but not more than 297,8 mm,

—a length of 107,75 mm or more but not more than 108,25 mm,

—more than 0,2 % but not more than 2 % of triisopropanolamine (CAS RN 122-20-3)

—a length of 245,48 mm or more but not more than 287,5 mm,

—a polyoxymethylene plastic ball seat,

—reaction mass of bis(1,2,2,6,6-pentamethyl-4-piperidyl) sebacate and methyl 1,2,2,6,6-pentamethyl-4-piperidyl sebacate (CAS RN 1065336-91-5) with a purity by weight of 25 % or more, but not more than 40 %

—a mixture of: bis(2,2,6,6-tetramethyl-1-octyloxypiperidin-4-yl)-1,10-decanedioate and 1,8-bis[(2,2,6,6-tetramethyl-4-((2,2,6,6-tetramethyl-1-octyloxypiperidin-4-yl)-decan-1,10-dioyl)piperidin-1-yl)oxy]octane (CAS RN 129757-67-1) with a content by weight of 40 % or more, but not more than 60 %

—5 % or more but not more than 25 % of 1-methoxy-2-propanol (CAS RN 107-98-2)

—more than 49 % but not more than 53 % of 2-Ethylhexyl 3-[3-tert-butyl-4-hydroxy-5-(5-chloro-2H-benzotriazol-2-yl) phenyl]propionate (CAS RN 83044-90-0)

—with a median grain size of 150 μm or more, but not more than 250 μm,

—a thickness of 2,9 mm or more but not more than 3,5 mm,

—a length of 195 mm or more but not more than 1835 mm,

—equipped with double seat valves on the live steam side which are operated with a hydraulic servo of not more than 30 bar

—with a length of 779 mm or more but not more than 1141 mm,

—with a length of 3480 mm or more but not more than 4115 mm,

—with a hardness of 60 or more on the Hardness Brinell Wolfram (HBW) scale (2,5/62,5, according to ISO 6506),

—with a fixed sensor,

—designed to carry one or two containers at a time,

—with an operating voltage of 9 VDC or more but not more than 16 VDC,

—iron oxide (CAS RN 1309-37-1),

—height of 100 mm or more but not exceeding 135 mm,

—a weight of 1,0245 kg or more but not more than 1,0445 kg,

—a length with gearhead of 116,1 mm or more but not more than 117,2 mm,

—an input power of 500 W or more but not more than 550 W,

—an outer diameter of motor magnet shaft end with dimension of 10,001 mm or more but no more than 10,007 mm,

—a flange diameter of 80 mm or more, but not more than 200 mm,

—an outer diameter of motor magnet shaft end with dimension of 10,001 mm or more but no more than 10,007 mm,

—with an operating temperature of – 40 °C or more but not more than 125 °C,

—a width of 280 mm or more but no more than 470 mm,

—kaolin (CAS RN 1332-58-7)

—2 electrical machines and gears,

—with individual replaceable, cooling tubes in brass or copper,

—a height of the lower side of inner diameter of 11,63 mm or more, but not more than 12,13 mm,

—a tubular female shaft in welded carbon steel tube (per with GB/T 699 grade 20),

—an outer diameter of 27,47 mm or more but not more than 28,38 mm,

—an outer diameter of 22,87 mm or more but not more than 22,92 mm,

—an external 18-tooth spline on all shaft length with major diameter of 28,7 mm or more but not more than 29 mm,

—an outer diameter of 6,38 mm or more but not more than 6,42 mm,

—an outer diameter of 23,95 mm or more but not more than 32,25 mm,

—a distance between the end of the threaded hole and the centre of the ball stud of 124 mm or more but not more than 194 mm,

—whether or not 10 % or more, but not more than 40 % of petroleum hydrocarbon resin (CAS RN 68132-00-3)

—0,5 % or more, but not more than 3 % of 2,6-di-tert-butyl-p-cresol (CAS RN 128-37-0)

—not more than 0,2 % of methyl styrene (CAS RN 98-83-9)

—29 % of butylacrylate, and

—on one side a highly hydrophobic, chemically neutral and non-reactive coating

—a low thermal shrinkage of 1 % or less at 150 °C for 30 minutes,

—where 90 % of the particles have a diameter of more than 3 μm,

—with a tensile strength of 240 N/mm² or more,

—with noise absorber,

—with a top or side mounting,

—with a valve’s base width of 22 mm or more but not more than 27 mm,

—width of 115 mm or more but not exceeding 150 mm,

—a hardness of the shaft of 40 or more on the Rockwell C hardness scale (HRC), but not more than 50 HRC,

—an external diameter of 13,86 mm or more but no more than 13,92 mm,

—output power of 350 W or more but not more than 400 W,

—terminals located across the radius 32,5 mm and separated by an angle of 21,8°,

—terminals located across the diameter 59,2 mm and separated by an angle 30,0°,

—aluminium magnesium vanadium oxide (CAS RN 70621-8-0),

—a maximum length of not more than 335 mm, measured from the beginning of the shaft to its outer end,

—terminals located across the radius 26,2 mm and separated by an angle 30,0°,

—with Cross-Linked Polyethylene (XLPE) or Thermoplastic Polyester Elastomer (TPE-E) wire insulation material,

—a height of 350 mm or more but no more than 595 mm,

—a width of 280 mm or more but no more than 470 mm,

—a height of the upper side of inner diameter of 3,25 mm or more, but not more than 3,5 mm,

—two spiders universal joint made of chromium alloy steel (per GB/T 5216 grade 20CrMnTiH),

—an inner hole of diameter 6,50 mm or more but not more than 6,58 mm,

—an internal hole of diameter 6,50 or more but not more than 6,58 mm,

—an 18-tooth internal spline with a minor diameter of 19,7 mm or more but not more than 20 mm,

—1 % of dihydrodicyclopentadienyl acrylate

—two external 18-tooth splines on both shaft ends with a major diameter of 6,70 mm or more but not more than 6,85 mm, as interface to pressing with matting input and output shafts,

—an interface for steering wheel connection either in a form of an external 40-tooth spline with major diameter of 17,1 mm or more but not more than 17,5 mm and an internal thread M12x1,75-6H or in a form of an external hexagon with a short diagonal of 15,05 mm or more but not more than 15,35 mm and an internal thread M10x1,5-6H,

—a ball stud diameter of 21,98 mm or more but no more than 22 mm,

—a low water vapor permeability of 2,5 g/m²•d or less, and

—a weight of 1345 g or more but not more than 1445 g,

—a width of 155 mm or more but not more than 545 mm,

—with a stroke of 450 mm or more but not more than 610 mm,

—with a stroke of 2750 mm or more but not more than 3180 mm,

—vanadium pentoxide (CAS RN 1314-62-1),

—with an anti-corrosion layer coated,

—with a valve’s length of 55 mm or more but not more than 110 mm,

—weight of 210 g or more but not more than 500 g

—a ring hardness of 90 or more on the Rockwell B hardness scale (HRB), but not more than 120 HRB,

—a maximum torque of motor with gearhead 246,6 mNm in 25 °C,

—an external diameter without bracket connector and pulley of 143,2 mm or more but not more than 143,8 mm,

—a motor housing made of ADC12 or AC46000 aluminium alloy die casting with composition of aluminium-silicon-copper (per JIS H5302 or EN1706 standard),

—a housing made of electrogalvanized steel (per JIS G3313 Grade SECE standard) using a deep-drawing stamping process,

—a housing length of not more than 265 mm, measured from the flange to the outer end,

—a housing made of ADC12 or AC46000 aluminium alloy die casting with composition of aluminium-silicon-copper (per JIS H5302 or EN1706 standard) and anodized coating (per ASTM B580 type E standard),

—a high breakdown voltage of 18 kV or more and

—with an operating voltage of 5 V,

—a length of 410 mm or more but no more than 690 mm,

—a height of 350 mm or more but no more than 595 mm,

—an overall height of 11,63 mm or more, but not more than 19,5 mm

—a length in nominal telescope position of 396 mm or more but not more than 467 mm,

—an external 26-teeth spline with major diameter 21,18 mm or more but not more than 21,44 mm,

—an external spline,

—entire surface shot peened,

—an interface either in a form of an internal 10-tooth spline of length of 98,0 mm or more but not more than 160 mm, with minor diameter of 16,1 mm or more but not more than 16,4 mm or in a form of an internal 48-tooth spline of length of 151 mm or more but not more than 160 mm, with minor diameter of 23,2 mm or more but not more than 23,3 mm,

—a threaded hole depth of 40,5 mm or more but no more than 52 mm with dimensions M14x1,5,

—3-zone structure including Euro Deep Gray colour printed zone^note

—a thermal conductivity lower than 2,5 mW/mK,

—adapted to work with hydraulic oil at a working pressure of 22 MPa or more but not more than 23 MPa,

—adapted to work with hydraulic oil at a working pressure of 23 MPa,

—with a height of 22 mm or more but not more than 26 mm,

—with 2, 5 or 7 control and power connection pins terminated with sensor temperature, heater or fuse type of socket,

—aluminium phosphate (CAS RN 7784-30-7),

—a no-load radial speed of motor with gearhead with 9900 rpm, at 24V in 25 °C,

—a rated speed of 16300 rpm or more but not more than 16500 rpm,

—a back electromotive force constant (Ke) of 0,03306 V-sec/rad or more but no more than 0,03654 V-sec/rad,

—a diameter of 88,600 mm or less but no less than 88,546 mm at the motor-system assembly interface,

—a back electromotive force constant (Ke) of 0,04009 V-sec/rad or more but no more than 0,04431 V-sec/rad,

—fitted with connectors at both ends,

—a weight of 70 kg or more but no more than 110 kg,

—a length of 410 mm or more but no more than 690 mm,

—a coupling interface on both ends with internal toothing,

—a partial discharge voltage of 1500 VDC or more (BG/T 123542.2-2009)

—a knurling on a part of outer surface of major diameter 26,0 mm or more but not more than 26,1 mm,

—a boot seal,

—an internal pressure of 0,1 Pa,

—whether or not with a maintenance-free bearing without the need for lubrication

—with a diameter of 128 mm or more but not more than 136 mm,

—with a weight of 3200 kg or more but not more than 4000 kg

—an external 37-teeth spline with major diameter of 41 mm or more but not more than 48 mm

—cerium oxide (CAS RN 1306-38-3),

—a back electromotive force harmonic order – 5th of no more than 0,36 % (of fundamental) and 7th of no more than 0,24 % (of fundamental),

—whether or not gold-plated or tin-plated

—two cardan joints on both sides,

—with or without an external 24-tooth spline and with a major diameter 24,75 mm or more but not more than 25 mm,

—a boot seal protector and retaining ring,

—an ambient temperature during operation of - 50 °C or more but not more than 70 °C

—with a weight of 220 g or more but not more than 250 g

—a weight of motor with gearhead of 70,5 g or more but not more than 71,5 g, a resistance to peak temperature of 140 °C or more (non-operating), a maximal air leak between shaft and shaft seals of 15 Pa/s at given 2 Bars of pressure,

—a weight of 2,33 kg or more but not more than 2,40 kg,

—a back electromotive force harmonic order – 5th of no more than 0,38 % (of fundamental) and 7th of no more than 0,25 % (of fundamental),

—a back electromotive force constant (Ke) of 0,03277 V-sec/rad or more but no more than 0,03623 V-sec/rad,

—a stator with single T-tooth design and single coil winding with 9/6 or 12/10 or 12/8 topology and surface magnets,

—ZSM-5 type zeolite (CAS RN 308081-08-5),

—14 functional pins for power and control purpose,

—a pulley

—a cogging torque of no more than 13 mNm,

—a back electromotive force harmonic order – 5th of no more than 0,35 % (of fundamental) and 7th of no more than 0,30 % (of fundamental),

—whether or not with electronic power steering controller,

—a cogging torque of no more than 20 mNm,

—a telescope shaft function with a range of 74 mm or more but not more than 115 mm,

—lubricant,

—a flexible printed circuit with length of 245 mm but no longer than 255 mm with mounted 8 pin male connector

—a friction torque in ambient temperature of no more than 22 mNm,

—a cogging torque of no more than 12 mNm,

—whether or not with pulley or coupling,

—a friction torque in ambient temperature of no more than 26,5 mNm,

0 %—31.12.20290.8865ex2811220080Amorphous silicon dioxide (CAS RN 112926-00-8),for use in the manufacture of tyres^note0 %—31.12.20290.8803ex29039980104-Bromo-2-fluorobiphenyl (CAS RN 41604-19-7) with a purity by weight of 99 % or more0 %—31.12.20290.8862ex29094980502,2′-[Oxybis(methylene)]bis[2-ethylpropane-1,3-diol] (CAS RN 23235-61-2) with a purity by weight of 95 % or more0 %—31.12.20290.8863ex2916140040Butyl methacrylate (CAS RN 97-88-1) with a purity by weight of 99 % or more0 %—31.12.20290.8861ex2918300043Ethyl 4-oxovalerate (CAS RN 539-88-8) with a purity by weight of 98 % or more0 %—31.12.20290.8511ex2920901085Diethyl carbonate (CAS RN 105-58-8) with a purity by weight of 99,9 % or more3,2 %—31.12.20250.8832ex2922290018Bis[(4-Methoxyphenyl)methyl]amine (CAS RN 17061-62-0) with a purity by weight of 96 % or more0 %—31.12.20290.8873ex2925290080Ethyl 4-[[(methylphenylamino)methylene]amino]benzoate (CAS RN 57834-33-0) with a purity of 99 % or more by weight0 %—31.12.20290.8831ex2933399916Tert-butyl (3R)-3-aminopiperidine-1-carboxylate (CAS RN 188111-79-7) with a purity by weight of 96 % or more0 %—31.12.20290.8833ex29333999172,4-Dichloro-3-nitropyridine (CAS RN 5975-12-2) with a purity by weight of 99 % or more0 %—31.12.20290.8834ex2933599556Ruxolitinib phosphate (INNM) (CAS RN 1092939-17-7) with a purity by weight of 99 % or more0 %—31.12.20290.8804ex29339980291,1-Dimethylethyl (4S)-3-amino-2-(4-fluoro-3,5-dimethylphenyl)-2,4,6,7-tetrahydro-4-methyl-5H-pyrazolo[4,3-c]pyridine-5-carboxylate (CAS RN 2212021-59-3) with a purity by weight of 99 % or more0 %—31.12.20290.8805ex29339980312-(2H-Benzotriazol-2-yl)-6-(2-phenylpropan-2-yl)-4-(2,4,4-trimethylpentan-2-yl)phenol (CAS RN 73936-91-1) with a purity by weight of 97 % or more0 %—31.12.20290.8809ex29339980626-O-tert-butyl 4a-O-methyl (4a)-1-(4-fluorophenyl)-4,5,7,8-tetrahydropyrazolo[3,4-g]isoquinoline-4a,6-dicarboxylate (CAS RN 864972-21-4) with a purity by weight of 95 % or more0 %—31.12.20290.8817ex2933998074N,N-Dimethyl-N-octadecyl-1-octadecanaminium (SP-4-2)-[29H,31H-phthalocyanine-2-sulfonato-N29,N30,N31,N32]cuprate (CAS RN 70750-63-9) with a purity by weight of 90 % or more0 %—31.12.20290.8888ex3204130085Mixture containing by weight:0 %—31.12.20290.8842ex3204150025Mixture in a 3:2 ratio of colourants C.I. Vat Blue 1 potassium salt (CAS RN 835912-68-0) and C.I. VAT Blue 1 sodium salt (CAS RN 894-86-0) and preparations based thereon with a combined content of colourants C.I. Vat Blue 1 salts of 40 % or more by weight0 %—31.12.20290.8827ex3204170051Colourant C.I. Pigment Yellow 174 (CAS RN 78952-72-4) and preparations based thereon with a colourant C.I. Pigment Yellow 174 content of 50 % or more by weight.0 %—31.12.20290.8798ex3204170052Colourant C.I. Pigment Red 112 (CAS RN 6535-46-2) and preparations based thereon with a colourant C.I. Pigment Red 112 content of 90 % or more by weight0 %—31.12.20290.8795ex3204170053Colourant C.I. Pigment Red 122 (CAS RN 980-26-7) and preparations based thereon with a colourant C.I. Pigment Red 122 content of 90 % or more by weight0 %—31.12.20290.8801ex3204170054Colourant C.I. Pigment Yellow 65 (CAS RN 6528-34-3) and preparations based thereon with a colourant C.I. Pigment Yellow 65 content of 90 % or more by weight0 %—31.12.20290.8816ex3204170056Colourant C.I. Pigment Red 146 (CAS RN 5280-68-2) and preparations based thereon with a colourant C.I. Pigment Red 146 content of 90 % or more by weight0 %—31.12.20290.8821ex3204170057Colourant C.I. Pigment Yellow 13 (CAS RN 5102-83-0) and preparations based thereon with a content of colourant C.I. Pigment Yellow 13 of 50 % or more by weight0 %—31.12.20290.8892ex3204170058Colourant C.I. Pigment Yellow 17 (CAS RN 4531-49-1) and preparations based thereon with a colourant C.I. Pigment Yellow 17 content of 90 % or more by weight0 %—31.12.20290.8877ex3204170059Colourant C.I. Pigment Yellow 180 (CAS RN 77804-81-0) and preparations based thereon with a colourant C.I. Pigment Yellow 180 content of 90 % or more by weight0 %—31.12.20290.8881ex3204190074Colourant C.I. Solvent Red 135 (CAS RN 71902-17-5) and preparations based thereon with a colourant C.I. Solvent Red 135 content of 90 % or more by weight0 %—31.12.20290.8883ex3204190076Colourant C.I. Solvent Red 52 (CAS RN 81-39-0) and preparations based thereon with a colourant C.I. Solvent Red 52 content of 90 % or more by weight0 %—31.12.20290.8880ex3204190078Colourant C.I. Solvent Yellow 114 (CAS RN 17772-51-9) and preparations based thereon with a colourant C.I. Solvent Yellow 114 content of 90 % or more by weight0 %—31.12.20290.8874ex3206410010Colourant C.I. Pigment Blue 29 (CAS RN 57455-37-5) and preparations based thereon with a colourant C.I. Pigment Blue 29 content of 90 % or more by weight0 %—31.12.20290.8800ex3206497060Colourant C.I. Pigment Yellow 164 (CAS RN 68412-38-4) and preparations based thereon with a colourant C.I. Pigment Yellow 164 content of 90 % or more by weight0 %—31.12.20290.8830ex3809910020Aqueous antimony pentoxide mixture containing by weight:0 %—31.12.20290.8872ex3812399023UV stabilizer, containing by weight:0 %—31.12.20290.8806ex3812399028UV stabilizer based on a mixture of0 %—31.12.20290.8807ex3812399033UV stabilizer based on:0 %—31.12.20290.8864ex3812399038UV stabiliser containing by weight:0 %—31.12.20290.8870ex3812399043Reaction mass containing by weight:0 %—31.12.20290.8840ex3815909055Catalytic Additives for fluid catalytic cracking (FCC), not containing Y type zeolite (CAS RN 308079-79-0), and not being an FCC (Fluid Catalytic Cracking) base catalyst, in the form of powder, consisting of a mixture of one or more of the following active substances:and one or more of the following inert substances:0 %—31.12.20290.8835ex3824999225Mixture containing by weight:0 %—31.12.20290.8886ex3824999228Preparation containing by weight:0 %—31.12.20290.8887ex3824999248Preparation containing by weight:0 %—31.12.20290.8875ex3824999666Vulcanizing agent containing by weight:0 %—31.12.20290.8828ex3906909071Acrylonitrile-styrene-acrylate copolymer in the form of granules containing by weight:0 %—31.12.20290.8882ex3907291130Mixture containing by weight:0 %—31.12.20290.8896ex3907291140Ethoxylated glycerol (CAS RN 31694-55-0) with a hydroxyl number of 541 or more but not more than 587 (ASTM 4274)0 %—31.12.20290.8848ex3920300030Opaque layer, whether or not printed, biaxially oriented, high impact polystyrene foil in rolls with:0 %—31.12.20290.8839ex3920621985Three-layer transparent plastic film consisting of a 15 μm fluorinated polymer (FCC) (EVA) layer, a 275 μm polyethylene terephthalate (PET) layer and a 25 μm fluorinated polymer (FCC) layer with:to be used as a protective layer on the back of photovoltaic modules0 %—31.12.20290.8860ex7007198086A ready-to-install, circular graded tempered glass of the cover of door assembly in washing machines with:0 %—31.12.20290.8858ex7019801030Vacuum insulation panel, consisting of a gas-tight aluminum foil housing surrounding a rigid, air-free core with:0 %—31.12.20290.8903ex7019900060Vacuum insulation panel, consisting of a gas-tight aluminum foil housing surrounding a rigid, air-free core with:0 %—31.12.20290.8818ex8406810010Industrial steam turbine with:0 %—31.12.20290.8851ex8412218030Linear acting hydraulic cylinder of a kind used in the machines for handling cargo containers:0 %—31.12.20290.8850ex8412218040Linear acting hydraulic cylinder of a kind used in the arms of machines for handling cargo containers:0 %—31.12.20290.8899ex8414308940Electrical compressor for motor vehicle air conditioning system:for use in the manufacture of motor vehicles of subheading 870340^note0 %p/st31.12.20290.8785ex8414900045Pressure casted rotor front plate or cover of an electric supercharger:0 %—31.12.20290.8856ex8418999040An evaporator being a type of heat exchanger, consisting of aluminium pipes with copper ends enclosed with aluminium radiators:for use in the manufacture of products of subheadings 841810, 841821, 841840^note0 %—31.12.20290.8853ex8431200070Container spreader for lifting empty 20′ and 40′ cargo containers:for use in the manufacture of self-propelled container handlers^note0 %—31.12.20290.8814ex8481805980Solenoid valve for combustion engine oil pump to regulate the quantity of oil in the pump:for use in the manufacture of motor vehicle engines^note0 %—31.12.20290.8784ex8481900025Die-cast aluminium housing for electronic throttle control or exhaust gas recirculation systems, comprising the following features:0 %—31.12.20290.8857ex8483109550Drum shaft for torque transmission, in steel (to SM45C for shaft standard and STS430 for ring standard) with:0 %—31.12.20290.8847ex8501310052Electric brushless direct current motor finished with biocompatible materials such as stainless steel according to specification 17-4 PH or type 303, 316L, 400 with:for use in the manufacture of medical devices with right-left rotation and oscillation function^note0 %p/st31.12.20290.8855ex8501310054Brushless DC electric motor, with:0 %p/st31.12.20290.8844ex8501510025Electric permanent magnet synchronous motor with:0 %p/st31.12.20290.8845ex8501510035Electric permanent magnet synchronous motor with:0 %p/st31.12.20290.8902ex8501522070Automotive-ready brushless permanently excited magnet synchronous alternating current motor with:0 %p/st30.06.20300.8846ex8501522080Electric permanent magnet synchronous motor with:0 %p/st31.12.20290.8841ex8537109175Printed circuit board equipped with a microcontroller for operating and/or control purposesfor use in the manufacture of household appliances of subheadings 732111, 841460, 841810, 841821, 841829, 841840, 842211, 845011, 845012, 845019, 845020, 845121, 845129, 851660^note0 %—31.12.20290.8849ex8544300020Insulated electrical multicore cable for the EPS-system (Electrical Power Steering) of a motor vehicle:0 %—31.12.20290.8859ex8544429055Wire harness for the transmission of signals and/or electrical power,for connection of power supply with main printed (circuit) board assembly (PBA) and electrical components of refrigerator or washing machine^note0 %—31.12.20290.8820ex8708402025Transmission assembly consisting of:for use in the manufacture of motor vehicles of subheading 870322 and 870323^note0 %—31.12.20290.8819ex8708405025Transmission assembly housing 3 other shafts inside it and offering a rotating switch for shift position, consisting of:for use in the manufacture of motor vehicles of subheadings 870340 and 870360^note0 %—31.12.20290.8812ex8708913540Radiators:for use in the production of engine and charge air cooling with a weight of 265 kg or more but not more than 599 kg^note0 %—31.12.20290.8775ex8708949910Hub gear made of cold rolled carbon steel (per ASTM A1008), molded into the plastic and pressed on pinion, with:for use in the manufacture of vehicle’s steering system^note0 %—31.12.20290.8777ex8708949920Intermediate steering shaft forming part of the steering column with:for use in the manufacture of vehicle’s steering system^note0 %—31.12.20290.8778ex8708949930Lower assist shaft as part of the steering column made of carbon steel (per GB/T699 grade 45 or JIS G4051 grade S45C) with:for use in the manufacture of vehicle’s steering system^note0 %—31.12.20290.8779ex8708949940Upper assist shaft as part of the steering column made of carbon steel (per GB/T699 grade 45) with:for use in the manufacture of vehicle’s steering system^note0 %—31.12.20290.8780ex8708949950Lower shaft as part of the steering column made of aluminium alloy (per ASTM B221M grade 6105), air quenched and tempered with:for use in the manufacture of vehicle’s steering system^note0 %—31.12.20290.8782ex8708949960Torsion bar as part of the steering column made of carbon alloy steel (per SAE J1268, grade 5160H of modified chemistry for carbon content of 0,53 or more, but not more than 0,56) with:for use in the manufacture of vehicle’s steering system^note0 %—31.12.20290.8781ex8708949970Tubular steering shaft as part of the steering column made of carbon steel welded tube (per EN 10305/2, E235 + C or GB/T699 grade 20) with:for use in the manufacture of vehicle’s steering system^note0 %—31.12.20290.8771ex8708999743Outer tie rod with a housing made of AISI 4137 (SCM435) steel or EN10083/2- C45R + N steel or JIS G4053-SCM435 low alloy steel, with:for use in the manufacture of vehicle’s steering system^note0 %—31.12.2029

Article 1#

Article 2#

Article 1 #

Article 2 #