Commission Implementing Regulation (EU) 2016/1789

Contents

THE EUROPEAN COMMISSION,Having regard to the Treaty on the Functioning of the European Union,Having regard to Regulation (EU) No 167/2013 of the European Parliament and of the Council of 5 February 2013 on the approval and market surveillance of agricultural or forestry vehicles^note, and in particular Article 22(4), Article 25(2) and (3), Article 27(1), Article 33(2), Article 34(3), Article 35(4) and Article 53(8) thereof,Whereas:

(1)Commission Implementing Regulation (EU) 2015/504^note lays down, inter alia, the templates for certain documents that are drawn up in the context of the approval and market surveillance of agricultural and forestry vehicles. It is necessary for the purposes of clarity and comprehensiveness that additional information on the maximum towable mass of the rear three-point lifting mechanism be indicated in the information document and in the certificate of conformity.

(2)In order to better identify a vehicle’s category or subcategory, the maximum and minimum track width of each tyre combination should be stated in the information document.

(3)In order to increase the consistency and completeness of the information provided, the information

(4)The certificate of conformity should be simplified in order to reduce the burden on manufacturers.

(5)The information in the test results sheet related to braking should be extended and improved for the purposes of clarity and consistency.

(6)In order to provide assistance to the technical services when drawing up braking test reports, specific templates for those test reports should be provided.

(7)In order to improve the readability and clarity of the text, certain changes should be made to provisions containing contradictions or redundant information and certain references should be amended.

(8)Implementing Regulation (EU) 2015/504 should therefore be amended accordingly.

(9)In order to allow additional time for manufacturers and national authorities to achieve a timely application of the amendments provided for in this Regulation, this Regulation should enter into force as a matter of urgency, especially taking into account that Regulation (EU) No 167/2013 became applicable on 1 January 2016 and that related administrative requirements will become compulsory with regard to all new vehicles registered or placed on the market as from 1 January 2018.

(10)The measures provided for in this Regulation are in accordance with the opinion of the committee referred to in Article 69(1) of Regulation (EU) No 167/2013,

HAS ADOPTED THIS REGULATION:

Article 1 #

Implementing Regulation (EU) 2015/504 is amended as follows:

(1)Annex I is amended in accordance with Annex I to this Regulation;

(2)Annex II is amended in accordance with Annex II to this Regulation;

(3)Appendix 1 to Annex III is amended in accordance with Annex III to this Regulation;

(4)Annex IV is amended in accordance with Annex IV to this Regulation;

(5)Annex V is amended in accordance with Annex V to this Regulation;

(6)Annex VII is amended in accordance with Annex VI to this Regulation;

(7)Annex VIII is amended in accordance with Annex VII to this Regulation.

Article 2 #

This Regulation shall enter into force on the day following that of its publication in the Official Journal of the European Union.

Annex I

(1)in the list of appendices, the row relating to Appendix 8 is replaced by the following:8 | Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) the installation of rear-view mirrors as a system |

(2)Part A is amended as follows:

(a)in point 1.1., the following point (j) is added:‘(j)For vehicles of categories T2, T3 and T4.3 equipped with foldable ROPS with an automatic locking system, a certificate of the manufacturer stating that the preliminary test has been done according to the test procedure set out in point 5.5. of Part B3 of Annex IX to Commission Delegated Regulation (EU) No 1322/2014^note.

(b)in point 2., in the Explanatory notes relating to the information folder sheet, explanatory note (5) is amended as follows:‘(5)For engines indicate the information relative to the engine type or the engine family type, as applicable without the type-approval extension number.’

(3)Part B is amended as follows:

(a)in point 3.1., Table 1-1 is replaced by the following:Table 1-1Lists of systems, components and separate technical units which may be subject to an EU type-approvalAppendix | System or component/separate technical unit (STU) | Commission Delegated Regulation (EU) 2015/96 Annex number | As amended by and/or at the stage of implementation1 | System: installation of an engine/engine family | II |2 | System: external sound level | III |3 | Component/STU: engine/engine family | I |Appendix | System or component/separate technical unit (STU) | Commission Delegated Regulation (EU) 2015/208 Annex number | As amended by and/or at the stage of implementation4 | System: driver information | X |5 | System: installation of lighting and light-signalling devices | XII |6 | System: electro-magnetic compatibility | XV |7 | System: installation of audible warning device(s) | XVI |8 | System: installation of rear-view mirrors | IX |9 | System: installation of crawler undercarriage | XXXIII |10 | STU: electro-magnetic compatibility of electrical / electronic sub-assemblies | XV |11 | Component/STU: ballast masses | XXIII |12 | Component/STU: lateral and/or rear protective structure | XXVI / XXVII |13 | Component: tyre | XXX |14 | Component/STU: mechanical coupling | XXXIV |Appendix | System or component/separate technical unit (STU) | Commission Delegated Regulation (EU) 2015/68 Annex number | As amended by and/or at the stage of implementation15 | System: braking | II |Appendix | System or component/separate technical unit (STU) | Commission Delegated Regulation (EU) No 1322/2014 Annex number | As amended by and/or at the stage of implementation16 | System: driver's exposure to noise level | XIII |17 | System: seat-belt anchorages | XVIII |18 | System: protection against hazardous substances | XXIX |19 | STU: roll-over protective structure (ROPS) | VI / VII / VIII / IX / X |20 | STU: falling objects protective structure (FOPS) | XI |21 | Component/STU: driver's seat | XIV |22 | Component/STU: safety belts | XIX |23 | STU: protection against penetrating objects (OPS) | XX |

(b)point 5 is amended as follows:

(i)entry 1.6.1.1. is deleted;

(ii)the following entry 1.6.3. is inserted:‘1.6.3.The vehicle identification number of the type begins with: …’;

(iii)entry 2.5.1. is replaced by the following:‘2.5.1.Type-approval of: engine type/engine family⁽⁴⁾’;

(iv)entry 3.3. is replaced by the following:‘3.3.Axles and wheels:’;

(v)entry 4.1.2.1.2. is replaced by the following:‘4.1.2.1.2.In the case of a rigid drawbar or centre-axle R- or S-category vehicle indicate the vertical load on the front coupling point (S):… kg’;

(vi)entry 4.1.2.2. is replaced by the following:‘4.1.2.2.Mass(es) and tyre(s)Tyre combi-nation No | Axle No | Tyre dimension incl load capacity index & speed category symbol | Rolling radius(1) [mm] | Tyre Load rating per tyre [kg] | Maximum permissible mass per axle [kg] | Maximum permissible mass of the vehicle [kg] | Maximum permissible vertical load on the coupling point [kg] | Track width [mm]Minimum | Maximum1 | 1 | … | | … | … | … | … | … | …2 | … | | … | … | … | … | … | …… | … | | … | … | … | … | … | …2 | 1 | … | | … | … | … | … | … | …| 2 | … | | … | … | … | … | … | …| … | … | | … | … | … | … | … | …… | 1 | … | | … | … | … | … | … | …| 2 | … | | … | … | … | … | … | …| … | … | | … | … | … | … | … | …

(vii)entry 4.1.2.4. is deleted;

(viii)entry 4.1.3. is replaced by the following:‘4.1.3.Technically permissible towable mass(es) for T- or C-category vehicles for each chassis/ braking configuration of the R- or S-category vehicle (for R- and S-category vehicles, indicate the maximum permissible load(s) on the rear coupling point):R- and S category vehicleBrake | Drawbar | Rigid drawbar | Centre-axleUnbraked | … kg | … kg | … kgInertia-braked | … kg | … kg | … kgHydraulic braked | … kg | … kg | … kgPneumatic braked | … kg | … kg | … kg

(ix)entry 4.1.4. is replaced by the following:‘4.1.4.Total technically permissible mass(es) of the tractor (T- or C-category vehicle) and towed vehicle (R- or S-category vehicle) combination for each chassis/braking configuration of the R- or S-category vehicle:R- and S category vehicleBrake | Drawbar | Rigid drawbar | Centre-axleUnbraked | … kg | … kg | … kgInertia-braked | … kg | … kg | … kgHydraulic braked | … kg | … kg | … kgPneumatic braked | … kg | … kg | … kg;

(x)entries 4.1.5. to 4.1.5.3. are deleted;

(xi)entry 4.2.1.3. is replaced by the following:‘4.2.1.3.Height (in running order)⁽³³⁾’;

(xii)the following entries 4.2.1.3.1. and 4.2.1.3.2. are inserted after entry 4.2.1.3.:‘4.2.1.3.1.Maximum … mm4.2.1.3.2.Minimum … mm’;

(xiii)entry 5.1.2.2. is deleted;

(xiv)entry 5.6. is replaced by the following:‘5.6.Actual forward movement of powered wheels corresponding to one complete revolution of the wheel: … mm’;

(xv)entries 6.6. and 6.7. are replaced by the following:‘6.6.Rated speed: … min^–16.7.Maximum torque speed: … min^–1’;

(xvi)entry 6.18., including all its sub-entries, is replaced by the following:‘6.18.Fuel feed for diesel engines6.18.1.Feed pump6.18.1.1Pressure⁽⁷⁾ … kPa or characteristic diagram: …6.18.2.Injection system6.18.2.1.Pump6.18.2.1.1.Make(s): …6.18.2.1.2.Type(s): …6.18.2.1.3.Delivery: … and … mm³⁽⁷⁾ per stroke or cycle at full injection at pump speed of: … rpm (rated) and: … rpm (maximum torque) respectively, or characteristic diagram: …6.18.2.1.3.1.Method used: on engine/on pump bench⁽⁴⁾6.18.2.2.Injection advance:6.18.2.2.1.Injection advance curve⁽⁷⁾: …6.18.2.2.2.Timing⁽⁷⁾: …6.18.2.3.Injection piping:6.18.2.3.1.Length: … mm6.18.2.3.2.Internal diameter: … mm6.18.2.4.Injector(s)6.18.2.4.1.Make(s) …6.18.2.4.2.Type(s): …6.18.2.4.3.Opening pressure⁽⁷⁾: … kPa, or characteristic diagram: …6.18.2.5.Governor6.18.2.5.1.Make(s) …6.18.2.5.2.Type(s): …6.18.2.5.3.Speed at which cut-off starts under full load⁽⁷⁾: … min^{– 1}6.18.2.5.4.Maximum no-load speed⁽⁷⁾: … min^{– 1}6.18.2.5.5.Idling speed⁽⁷⁾: … min^{– 1}6.18.2.6.Cold-start system6.18.2.6.1.Make(s): …6.18.2.6.2.Type(s): …6.18.2.6.3.Description: …’;

(xvii)entry 6.19.4.2. is replaced by the following:‘6.19.3.2.Type(s): …’;

(xviii)entry 7.1.1. is replaced by the following:‘7.1.1.Combustion cycle: positive ignition/compression ignition⁽⁴⁾’;

(xix)entries 8.6. and 8.7. are replaced by the following:‘8.6.Rated speed: … min^–18.7.Maximum torque speed: … min^–1’;

(xx)entry 8.12.2., including all its sub-entries, is replaced by the following:‘8.12.2.Air8.12.2.1.Blower: yes/no(4)8.12.2.1.1.Characteristics of the blower. …8.12.2.1.2.Drive ratio(s) (if applicable): …’;

(xxi)entry 8.17., including all its sub-entries, is replaced by the following:‘8.17.Measures taken against air pollution8.17.1.Device for recycling crankcase gases: yes/no⁽⁴⁾8.17.2.Additional anti-pollution devices (if any):8.17.2.1.Catalytic converter: yes/no⁽⁴⁾8.17.2.1.1.Make: …8.17.2.1.2.Type …8.17.2.1.3.Number of catalytic converters and elements …8.17.2.1.4.Dimensions and volume of the catalytic converter(s): …8.17.2.1.5.Type of catalytic action …8.17.2.1.6.Total charge of precious metals: …8.17.2.1.7.Relative concentration: …8.17.2.1.8.Substrate (structure and material): …8.17.2.1.9.Cell density: …8.17.2.1.10.Type of casing for the catalytic converter(s): …8.17.2.1.11.Location of the catalytic converter(s) (place(s) and maximum/minimum distance(s) from engine: …8.17.2.1.12.Normal operating range: … K8.17.2.1.13.Consumable reagent (where appropriate) …8.17.2.1.13.1.Type and concentration of reagent needed for catalytic action: …8.17.2.1.13.2.Normal operational temperature range of reagent: … K8.17.2.1.13.3.International standard (if applicable): …8.17.2.1.14.NO_x sensor: yes/no⁽⁴⁾8.17.2.1.15.Oxygen sensor: yes/no⁽⁴⁾8.17.2.1.15.1.Make: …8.17.2.1.15.2.Type …8.17.2.1.15.3.Location: …8.17.2.1.16.Air injection: yes/no⁽⁴⁾8.17.2.1.16.1.Type: pulse air/air pump/other⁽⁴⁾ (if other specify: …)8.17.2.1.17.EGR: yes/no⁽⁴⁾8.17.2.1.17.1.Characteristics (cooled/uncooled, high pressure/low pressure, etc.): …8.17.2.1.18.Particulate trap: yes/no⁽⁴⁾8.17.2.1.18.1.Dimensions and capacity of the particulate trap: …8.17.2.1.18.2.Type and design of the particulate trap: …8.17.2.1.18.3.Location (place(s) and maximum/minimum distance(s) from engine: …8.17.2.1.18.4.Method or system of regeneration, description and/or drawing: …8.17.2.1.18.5.Normal operating temperature range: … K and pressure range: …kPa8.17.2.1.19.Other systems: yes/no⁽⁴⁾8.17.2.1.19.1.Description and operation: …’;

(xxii)entry 8.18., including all its sub-entries, is replaced by the following:‘8.18.Fuel feed for diesel engines8.18.1.Feed pump8.18.1.1Pressure⁽⁷⁾ … kPa or characteristic diagram: …8.18.2.Injection system8.18.2.1.Pump8.18.2.1.1.Make(s): …8.18.2.1.2.Type(s): …8.18.2.1.3.Delivery: … and …mm³⁽⁷⁾ per stroke or cycle at full injection at pump speed of: … rpm (rated) and: … rpm (maximum torque) respectively, or characteristic diagram: …8.18.2.1.3.1.Method used: on engine/on pump bench⁽⁴⁾8.18.2.2.Injection advance:8.18.2.2.1.Injection advance curve⁽⁷⁾: …8.18.2.2.2.Timing⁽⁷⁾: …8.18.2.3.Injection piping:8.18.2.3.1.Length: … mm8.18.2.3.2.Internal diameter: … mm8.18.2.4.Injector(s)8.18.2.4.1.Make(s) …8.18.2.4.2.Type(s): …8.18.2.4.3.Opening pressure⁽⁷⁾: … kPa, or characteristic diagram: …8.18.2.5.Governor8.18.2.5.1.Make(s) …8.18.2.5.2.Type(s): …8.18.2.5.3.Speed at which cut-off starts under full load⁽⁷⁾: … min^–18.18.2.5.4.Maximum no-load speed⁽⁷⁾: … min^–18.18.2.5.5.Idling speed⁽⁷⁾: … min^–18.18.2.6.Cold-start system8.18.2.6.1.Make(s): …8.18.2.6.2.Type(s): …8.18.2.6.3.Description: …’;

(xxiii)entry 8.19. is replaced by the following:‘8.19.Fuel feed for petrol engines’;

(xxiv)entry 9., including all its sub-entries, is replaced by the following:‘9.ENERGY STORAGE DEVICE(S)⁽¹¹⁾9.1.Description: battery/capacitor/flywheel/generator(4)9.2.Identification number: …9.3.Kind of electrochemical couple: …9.4.Energy stored9.4.1.For battery, voltage: … and capacity: … Ah in 2h9.4.2.For capacitor: … J9.4.3.For flywheel/generator⁽⁴⁾: … J9.4.3.1.Flywheel moment of inertia: … kg m²9.4.3.1.1.Additional moment of inertia if no gear is engaged: … kg m²9.5.Charger: on-board/external/without⁽⁴⁾’;

(xxv)entry 10.4.4.1. is replaced by the following:‘10.4.4.1.Exhaust noise-abatement device containing fibrous materials: yes/no⁽⁴⁾’;

(xxvi)entry 11., including all its sub-entries, is replaced by the following:‘11.DRIVE-TRAIN AND CONTROL⁽¹³⁾11.1.Brief description and schematic drawing of the vehicle drive-train and its control system (gear shift control, clutch control or any other element of drive-train):11.2.Transmission11.2.1.Brief description and schematic drawing of gear shift system(s) and its control: …11.2.2.Diagram and or drawing of the transmission system: …11.2.3.Type of transmission: mechanical/hydraulic/electric/other⁽⁴⁾ (if other specify …)11.2.4.Brief description of the electrical/electronic components (if any): …11.2.5.Location relative to the engine: …11.2.6.Method of control: …11.2.7.Transfer box: with/without⁽⁴⁾11.2.8.Type of gear shift system(s)⁽²⁴⁾: …11.3.Clutch (if any)11.3.1.Brief description and schematic drawing of the clutch and its control system:11.3.2.Maximum torque conversion: …11.4.Gear ratiosGear | Internal gearbox ratios (ratios of engine to gearbox output shaft revolutions) | Internal transfer box ratios (ratios of engine to transfer box output shaft revolutions) | Final drive ratio(s) (ratio of gearbox output shaft to driven wheel revolutions) | Total gear ratios | Ratio (engine speed/vehicle speed) for manual transmission onlyMaximum for CVT123 | | | | |Minimum for CVTReverse1… | | | | |11.5.Differential lock11.5.1.Differential lock: yes/no/optional⁽⁴⁾’;

(xxvii)entry 22.3.1. is replaced by the following:‘22.3.1.Photographs, drawings and/or an exploded view of the interior fittings, showing the parts in the passenger compartment and the materials used (with the exception of interior rear view mirrors), arrangement of controls, seats and their rear parts, head restraints, roof and opening roof, doors and window winders and other non-specified fittings: …’;

(xxviii)entry 25.5.2. is replaced by the following:‘25.5.2.Rated voltage or air pressure: … V / kPa(4)’;

(xxix)entry 28., including all its sub-entries, is replaced by the following:‘28.REAR REGISTRATION PLATE(S) SPACE28.1.Location of registration plate(s) (indicate variants where necessary; drawings may be used as appropriate):28.1.1.Height above road surface, upper edge: …mm28.1.2.Height above road surface, lower edge: …mm28.1.3.Distance of the centre line from the longitudinal median plane of the vehicle: …mm28.1.4.Dimensions (length x width): …mm x …mm28.1.5.Inclination of the plane to the vertical: …degr.28.1.6.Angle of visibility in the horizontal plane: ….degr.’

(xxx)entry 29., including all its sub-entries, is replaced by the following:‘29.BALLAST MASSES29.1.Detailed technical description (including photographs or drawings with dimensions) of the ballast masses and how they are mounted on the tractor:29.2.Number of sets of ballast masses: …29.2.1.Number of components on each set: Set 1: … Set 2: …Set …29.3.Mass of the components on each set: Set 1: …kg Set 2: …kg Set …:…kg29.3.1.Total mass of each set: Set 1: …kg Set 2: …kg Set …:…kg29.4.Total mass of ballast masses: …kg29.4.1.Distribution of these masses among the axles: …kg29.5.Material(s) and method of construction: …’;

(xxxi)entry 38.5. is replaced by the following:‘38.5.Description of the mechanical coupling:Type (according to Appendix 1 of Annex XXXIV to Commission Delegated Regulation (EU) 2015/208):…Make:…Manufacturer’s type designation:…Maximum horizontal load/D-Value^(4)(44):… kg/kN⁽⁴⁾Towable mass (T) ^(4)(44):… tonnesMaximum permissible vertical load on the coupling point (S)⁽⁴⁴⁾:… kgPhotographs and scale drawings of the coupling device. These drawings shall in particular show the required dimensions in detail as well as the measurements for mounting the device.Short technical description of the coupling device specifying the type of construction and the material used.Type of TestStatic/Dynamic ⁽⁴⁾(EU) type-approval mark or -number of

—drawbar eyes, coupling heads or similar coupling devices that shall be attached to the mechanical coupling (in the case of hinged or rigid drawbars)

—type-approval mark or –number of mechanical couplings that shall be attached to the ladder frame /trailer hitch support (if restricted to certain types):

…’;

(xxxii)the following entry 39.2. is inserted:‘39.2.Maximum towable mass⁽¹⁶⁾: … kg’;

(xxxiii)entry 43.1. is replaced by the following:‘43.1.Brief description of the braking system(s) installed on the vehicle⁽⁵⁵⁾: …’;

(xxxiv)entry 43.3. is deleted;

(xxxv)entry 43.6., including all its sub-entries, is replaced by the following:‘43.6.Towed vehicle braking devices43.6.1.Towed vehicle braking control system technology: Hydraulic / Pneumatic / Electric/None⁽⁴⁾43.6.2.Towed vehicle-brake actuating device (description, characteristics): …43.6.3.Description of the connectors, couplings and safety devices (including drawings, sketches and the identification of any electronic parts): …43.6.4.Connections type: Single line/Two-lines/None⁽⁴⁾43.6.4.1.Supply pressure Hydraulic: Single line: … kPa Two lines: … kPa43.6.4.2.Supply pressure Pneumatic: Two lines: … kPa43.6.5.Presence of ISO 7638:2003 connector⁽¹⁵⁾: yes/no⁽⁴⁾’;

(xxxvi)before the heading ‘E. Information on vehicle construction’, the following entries are inserted:‘43.A.TOWED VEHICLE AXLE AND BRAKE INFORMATION DOCUMENT WITH RESPECT TO THE ALTERNATIVE TYPE I AND TYPE III PROCEDURE43.A.1.General43.A.1.1.Name and address of axle or vehicle manufacturer:43.A.2.Axle data43.A.2.1.Manufacturer (name and address): …43.A.2.2.Type/variant: …43.A.2.3.Axle identifier: ID1- …43.A.2.4.Test axle load (F_e): … daN43.A.2.5.Wheel and brake data according to the following figures 1A and 1B …43.A.3.Brake43.A.3.1.General information43.A.3.1.1.Make:43.A.3.1.2.Manufacturer (name and address):43.A.3.1.3.Type of brake (e.g. drum / disc):43.A.3.1.3.1.Variant (e.g. S-cam, single wedge etc.):43.A.3.1.4.Brake identifier: ID2-43.A.3.1.5.Brake data according to the figures 2A and 2B:43.A.3.2.Drum brake data43.A.3.2.1.Brake adjustment device (external/integrated): …43.A.3.2.2.Declared maximum brake input torque C_max: … Nm43.A.3.2.3.Mechanical efficiency: η = …43.A.3.2.4.Declared brake input threshold torque C0,dec: … Nm43.A.3.2.5.Effective length of the cam shaft: … mm43.A.3.3.Brake drum43.A.3.3.1.Max diameter of friction surface (wear limit) … mm43.A.3.3.2.Base material: …43.A.3.3.3.Declared mass: … kg43.A.3.3.4.Nominal mass: … kg43.A.3.4.Brake lining43.A.3.4.1.Manufacturer and address …43.A.3.4.2.Make …43.A.3.4.3.Type …43.A.3.4.4.Identification (type identification on lining) …43.A.3.4.5.Minimum thickness (wear limit) … mm43.A.3.4.6.Method of attaching friction material to brake shoe: …43.A.3.4.6.1.… Worst case of attachment (in the case of more than one):43.A.3.5.Disc brake data43.A.3.5.1.Connection type to the axle (axial, radial, integrated, etc.): …43.A.3.5.2.Brake adjustment device (external/integrated): …43.A.3.5.3.Max. actuation stroke: … mm43.A.3.5.4.Declared maximum input force Th_Amax: … daN43.A.3.5.4.1Cmax = ThAmax · l_e : … Nm43.A.3.5.5.Friction radius: r_e = … mm43.A.3.5.6.Lever length: l_e = … mm43.A.3.5.7.Input/output ratio (l_e/e_e): i = ….43.A.3.5.8.Mechanical efficiency: η = …43.A.3.5.9.Declared brake input threshold force Th_A0,dec: … N43.A.3.5.9.1.C_0,dec = Th_A0,dec · l_e : … Nm43.A.3.5.10.Minimum rotor thickness (wear limit): … mm43.A.3.6.Brake disc data …43.A.3.6.1.Disc type description: …43.A.3.6.2.Connection/mounting to the hub: …43.A.3.6.3.Ventilation (yes/no): …43.A.3.6.4.Declared mass: … kg43.A.3.6.5.Nominal mass: … kg43.A.3.6.6.Declared external diameter: … mm43.A.3.6.7.Minimum external diameter: … mm43.A.3.6.8.Inner diameter of friction ring: … mm43.A.3.6.9.Width of ventilation channel (if appl.): … mm43.A.3.6.10.Base material: …43.A.3.7.Brake pad data …43.A.3.7.1.Manufacturer and address: …43.A.3.7.2.Make:43.A.3.7.3.Type: …43.A.3.7.4.Identification (type identification on pad back plate): …43.A.3.7.5.Minimum thickness (wear limit): … mm43.A.3.7.6.Method of attaching friction material to pad back plate: …43.A.3.7.6.1.Worst case of attachment (in the case of more than one): …Figure 1AFigure 1BFigure 2AFigure 2Bxe (mm) | ae (mm) | he (mm) | ce (mm) | de (mm) | ee (mm) | α0e | α1e | be (mm) | re (mm) | Ae (cm2) | S1e (mm) | S2e (mm) | S3e (mm);| | | | | | | | | | | | |

(xxxvii)entries 45.6.3.1. to 45.6.3.4. are replaced by the following:‘45.6.3.1.SAE J1939-13 (Serial control and communications vehicle network): yes/no⁽⁴⁾45.6.3.2.ISO 11783-2 (Tractors and machinery for agriculture and forestry – Serial control and communications data network): yes/no⁽⁴⁾45.6.3.3.ISO 15031-3 (Road vehicles – Communication between vehicle and external equipment for emissions-related diagnostics): yes/no⁽⁴⁾45.6.3.4.ISO 13400-4 (Road vehicles – Diagnostic communication over Internet Protocol (DoIP))⁽⁴⁾: yes/no⁽⁴⁾’;

(xxxviii)entry 46.2.1. is replaced by the following:‘46.2.1.In the case of roll bar: foldable/not foldable⁽⁴⁾’;

(xxxix)entry 46.2.2., including all its sub-entries, is replaced by the following:‘46.2.2.In the case of foldable roll bar:46.2.2.1.Folding operation: non-assisted / partially assisted / fully assisted⁽⁴⁾46.2.2.2.In case of non-assisted or partially assisted folding operation:46.2.2.2.1.Hand-operated foldable ROPS: with tools/ without tools⁽⁴⁾46.2.2.2.2.Photographs and detailed technical drawings showing the grasping area and a lateral and top view of the accessible zones. Dimensions and maximum forces for actuating the ROPS must figure on the drawings: …46.2.2.3.In case of partially assisted or fully assisted folding operation, brief description of the assistance devices as well as of their control devices, if any, and their location: …46.2.2.4.Locking mechanism: manual/automatic⁽⁴⁾46.2.2.4.1.For manual locking mechanisms, brief description of the locking mechanism and of its ergonomic design to avoid pinching or shearing hazards and to limit the force required for its operation: …46.2.2.4.2.For automatic locking mechanisms,46.2.2.4.2.1.Brief description of the locking mechanism, its control devices, if any, and their location: …46.2.2.4.2.2.Manufacturers' certificate set out in Note 2 of point 5.5. of Part B3 of Annex IX to Commission Delegated Regulation (EU) No 1322/2014: yes/no⁽⁴⁾’;

(xxxx)entry 49.4.1. is replaced by the following:‘49.4.1.Position of the driving seat: left/right/centre⁽⁴⁾’;

(xxxxi)entry 49.5., including all its sub-entries, is replaced by the following:‘49.5.Passenger seat(s)49.5.1.Number of passenger seats: …49.5.2.Location and arrangement⁽⁸⁾: …49.5.3.Dimensions of the passenger seat(s): …49.5.4.Main characteristics of the passenger seat(s): …49.5.5.Requirements under standard EN 15694:2009 (Agricultural and forestry tractors. Passenger seat. Requirements and test procedures) are met with relevant documentation included in the information document: yes/no/not applicable⁽⁴⁾49.5.6.Requirements under standard EN 15997:2011 (All terrain vehicles (ATVs - Quads). Safety requirements and test methods) on passenger seats for ATV Type II vehicle are met with relevant documentation included in the information document: yes/no/not applicable⁽⁴⁾’;

(xxxxii)entry 51.2., including all its sub-entries, is replaced by the following:‘51.2.Main power take-off51.2.1.Position: front/rear/other⁽⁴⁾ (if other specify: …)51.2.2.Revolutions per minute: … min^–151.2.2.1.Ratio of power take-off revolutions to that of the engine: …51.2.3.Optional: Power at the power take-off (PTO) at the rated speed(s) (in accordance with OECD Code 2⁽⁵⁷⁾ or ISO 789-1:1990 (Agricultural tractors – Test procedures – Part 1: Power tests for power take-off))Rated speed PTO(min–1) | Corresponding engine speed(min–1) | Power(kW)1-540 | … | …2-1000 | … | …540E | |1000E | |51.2.4.Power take-off guard (description, dimensions, drawings, photographs): …’;

(xxxxiii)entry 51.2.3. is replaced by the following:‘51.3.3.Optional: Power at the power take-off (PTO) at the rated speed(s) (in accordance with OECD Code 2⁽⁵⁷⁾ or ISO 789-1:1990 (Agricultural tractors – Test procedures – Part 1: Power tests for power take-off))Rated speed PTO(min–1) | Corresponding engine speed(min–1) | Power(kW)1-540 | … | …2-1000 | … | …540E | |1000E | |

(xxxxiv)entry 54.3. is replaced by the following:‘54.3.Number and position of safety belts and seats on which they can be used, please fill out table below:Safety belt configuration and associated information| | | Complete EU type-approval mark / ECE type-approval mark | Variant, if applicable | Belt adjustment device for height (indicate yes/no/optional)Driver's seat | | L | | |C | | |R | | |Passenger seat1 | | L | | |C | | |R | | |Passenger seat… | | L | | |C | | |R | | |

(xxxxv)entry 57., including all its sub-entries, is replaced by the following:‘57.DRIVER-OPERATED CONTROL DEVICES INCLUDING IDENTIFICATION OF CONTROL DEVICES, TELL-TALES AND INDICATORS57.1.Photographs and/or drawings of the arrangement of symbols and controls, tell-tales and indicators:57.2.Controls, tell-tales and indicators for which, when fitted, identification is mandatory, and symbols to be used for that purposeSymbol No | Device | Control / indicator available | Identified by symbol | Where | Tell-tale available | Identified by symbol | Where1 | Dipped-beam head lamps | | | | | |2 | Main-beam head lamps | | | | | |3 | Position (side) lamps | | | | | |4 | Front fog lamps | | | | | |5 | Rear fog lamp | | | | | |6 | Headlamp levelling device | | | | | |7 | Parking lamps | | | | | |8 | Direction indicators | | | | | |9 | Hazard warning | | | | | |10 | Windscreen wiper | | | | | |11 | Windscreen washer | | | | | |12 | Windscreen wiper and washer | | | | | |13 | Headlamp cleaning device | | | | | |14 | Windscreen demisting and defrosting | | | | | |15 | Rear window demisting and defrosting | | | | | |16 | Ventilating fan | | | | | |17 | Diesel pre-heat | | | | | |18 | Choke | | | | | |19 | Brake failure | | | | | |20 | Fuel level | | | | | |21 | Battery charging condition | | | | | |22 | Engine coolant temperature | | | | | |23 | Malfunction indicator light (MI) | | | | | |57.3.Controls, tell-tales and indicators for which, when fitted, identification is optional, and symbols which shall be used if they are to be identifiedSymbol No | Device | Control / indicator available | Identified by symbol | Where | Tell-tale available | Identified by symbol | Where1 | Parking brake | | | | | |2 | Rear window wiper | | | | | |3 | Rear window washer | | | | | |4 | Rear window wiper and washer | | | | | |5 | Intermittent windscreen wiper | | | | | |6 | Audible warning device | | | | | |7 | Hood | | | | | |8 | Seat belt | | | | | |9 | Engine oil pressure | | | | | |10 | Unleaded petrol | | | | | |11 | … | | | | | |12 | …. | | | | | || | | | | | |57.4.Brief description and schematic drawing of the locations, displacement, methods of operation and colour coding of the various control devices in the interior of the vehicle and showing for tractors without enclosed cab, how the accessibility to internal control devices from the ground has been avoided: …57.5.Brief description and schematic drawing of the locations, displacement, methods of operation and colour coding of the various control devices in the exterior of the vehicle and indicating the front and the rear hazard zones in accordance with Appendix 1 of Annex XXIII to Commission Delegated Regulation (EU) No 1322/2014: …57.6.Requirements under Annexes A and C of standard ISO 15077:2008 (Tractors and self-propelled machinery for agriculture – Operator controls – Actuating forces, displacement, location and method of operation) are met with relevant documentation included in the information document: yes/no⁽⁴⁾57.7.Requirements under paragraph 4.5.3 of standard ISO 4254-1:2013 (Agricultural machinery – Safety – Part 1: General requirements), with the exception of fingertip operation control devices, are met with relevant documentation included in the information document: yes/no⁽⁴⁾57.8.Requirements under standard EN 15997:2011 (All terrain vehicles (ATVs - Quads). Safety requirements and test methods) on throttle control and manual clutch control are met with relevant documentation included in the information document: yes/no/not applicable⁽⁴⁾57.9.For vehicles of T- and C-category, requirements under standard ISO 10975:2009 (Tractors and machinery for agriculture – Auto-guidance systems for operator-controlled tractors and self-propelled machines – Safety requirements) are met with relevant documentation included in the information document: yes/no/not applicable⁽⁴⁾’;

(c)Appendix 1 is amended as follows:

(i)entry 2.5.1. is replaced by the following:‘2.5.1.Type-approval of: engine type/engine family⁽⁴⁾’;

(ii)entry 5.1.2.2. is deleted;

(iii)entries 6.6. and 6.7. are replaced by the following:‘6.6.Rated speed: … min^–16.7.Maximum torque speed: … min^–1’;

(iv)entry 6.18., including all its sub-entries, is replaced by the following:‘6.18.Fuel feed for diesel engines6.18.1.Feed pump6.18.1.1Pressure⁽⁷⁾ … kPa or characteristic diagram: …6.18.2.Injection system6.18.2.1.Pump6.18.2.1.1.Make(s): …6.18.2.1.2.Type(s): …6.18.2.1.3.Delivery: … and … mm³⁽⁷⁾ per stroke or cycle at full injection at pump speed of: … rpm (rated) and: … rpm (maximum torque) respectively, or characteristic diagram: …6.18.2.1.3.1.Method used: on engine/on pump bench⁽⁴⁾6.18.2.2.Injection advance:6.18.2.2.1.Injection advance curve⁽⁷⁾: …6.18.2.2.2.Timing⁽⁷⁾: …6.18.2.3.Injection piping:6.18.2.3.1.Length: … mm6.18.2.3.2.Internal diameter: … mm6.18.2.4.Injector(s)6.18.2.4.1.Make(s) …6.18.2.4.2.Type(s): …6.18.2.4.3.Opening pressure⁽⁷⁾: … kPa, or characteristic diagram: …6.18.2.5.Governor6.18.2.5.1.Make(s) …6.18.2.5.2.Type(s): …6.18.2.5.3.Speed at which cut-off starts under full load⁽⁷⁾: … min^–16.18.2.5.4.Maximum no-load speed⁽⁷⁾: … min^–16.18.2.5.5.Idling speed⁽⁷⁾: … min^–16.18.2.6.Cold-start system6.18.2.6.1.Make(s): …6.18.2.6.2.Type(s): …6.18.2.6.3.Description: …’;

(v)entry 7.1.1. is replaced by the following:‘7.1.1.Combustion cycle: positive ignition/compression ignition⁽⁴⁾’;

(vi)entries 8.6. and 8.7. are replaced by the following:‘8.6.Rated speed: … min^–18.7.Maximum torque speed: … min^–1’;

(vii)entry 8.12.2., including all its sub-entries, is replaced by the following:‘8.12.2.Air8.12.2.1.Blower: yes/no⁽⁴⁾8.12.2.1.1.Characteristics of the blower. …8.12.2.1.2.Drive ratio(s) (if applicable): …’;

(viii)entry 8.17., including all its sub-entries, is replaced by the following:‘8.17.Measures taken against air pollution8.17.1.Device for recycling crankcase gases: yes/no⁽⁴⁾8.17.2.Additional anti-pollution devices (if any):8.17.2.1.Catalytic converter: yes/no⁽⁴⁾8.17.2.1.1.Make: …8.17.2.1.2.Type …8.17.2.1.3.Number of catalytic converters and elements …8.17.2.1.4.Dimensions and volume of the catalytic converter(s): …8.17.2.1.5.Type of catalytic action …8.17.2.1.6.Total charge of precious metals: …8.17.2.1.7.Relative concentration: …8.17.2.1.8.Substrate (structure and material): …8.17.2.1.9.Cell density: …8.17.2.1.10.Type of casing for the catalytic converter(s): …8.17.2.1.11.Location of the catalytic converter(s) (place(s) and maximum/minimum distance(s) from engine: …8.17.2.1.12.Normal operating range: …K8.17.2.1.13.Consumable reagent (where appropriate) …8.17.2.1.13.1.Type and concentration of reagent needed for catalytic action: …8.17.2.1.13.2.Normal operational temperature range of reagent: … K8.17.2.1.13.3.International standard (if applicable): …8.17.2.1.14.NOx sensor: yes/no⁽⁴⁾8.17.2.1.15.Oxygen sensor: yes/no⁽⁴⁾8.17.2.1.15.1.Make: …8.17.2.1.15.2.Type …8.17.2.1.15.3.Location: …8.17.2.1.16.Air injection: yes/no⁽⁴⁾8.17.2.1.16.1.Type: pulse air/air pump/other(4) (if other specify: …)8.17.2.1.17.EGR: yes/no⁽⁴⁾8.17.2.1.17.1.Characteristics (cooled/uncooled, high pressure/low pressure, etc.): …8.17.2.1.18.Particulate trap: yes/no⁽⁴⁾8.17.2.1.18.1.Dimensions and capacity of the particulate trap: …8.17.2.1.18.2.Type and design of the particulate trap: …8.17.2.1.18.3.Location (place(s) and maximum/minimum distance(s) from engine: …8.17.2.1.18.4.Method or system of regeneration, description and/or drawing: …8.17.2.1.18.5.Normal operating temperature range: … K and pressure range: … kPa8.17.2.1.19.Other systems: yes/no⁽⁴⁾8.17.2.1.19.1.Description and operation:… .’

(ix)entry 8.18., including all its sub-entries, is replaced by the following:‘8.18.Fuel feed for diesel engines8.18.1.Feed pump8.18.1.1Pressure⁽⁷⁾ … kPa or characteristic diagram: …8.18.2.Injection system8.18.2.1.Pump8.18.2.1.1.Make(s): …8.18.2.1.2.Type(s): …8.18.2.1.3.Delivery: … and … mm³⁽⁷⁾ per stroke or cycle at full injection at pump speed of: … rpm (rated) and: … rpm (maximum torque) respectively, or characteristic diagram: …8.18.2.1.3.1.Method used: on engine/on pump bench⁽⁴⁾8.18.2.2.Injection advance:8.18.2.2.1.Injection advance curve⁽⁷⁾: …8.18.2.2.2.Timing⁽⁷⁾: …8.18.2.3.Injection piping:8.18.2.3.1.Length: … mm8.18.2.3.2.Internal diameter: … mm8.18.2.4.Injector(s)8.18.2.4.1.Make(s) …8.18.2.4.2.Type(s): …8.18.2.4.3.Opening pressure⁽⁷⁾: … kPa, or characteristic diagram: …8.18.2.5.Governor8.18.2.5.1.Make(s) …8.18.2.5.2.Type(s): …8.18.2.5.3.Speed at which cut-off starts under full load⁽⁷⁾: … min^–18.18.2.5.4.Maximum no-load speed⁽⁷⁾: … min^–18.18.2.5.5.Idling speed⁽⁷⁾: … min^–18.18.2.6.Cold-start system8.18.2.6.1.Make(s): …8.18.2.6.2.Type(s): …8.18.2.6.3.Description: …’;

(x)entry 8.19. is replaced by the following:‘8.19.Fuel feed for petrol engines’;

(d)Appendix 2 is amended as follows:

(i)entry 2.5.1. is replaced by the following:‘2.5.1.Type-approval of: engine type/engine family⁽⁴⁾’;

(ii)entry 5.1.2.2. is deleted;

(iii)entry 10.4.4.1. is replaced by the following:‘10.4.4.1.Exhaust noise-abatement device containing fibrous materials: yes/no⁽⁴⁾’;

(e)Appendix 3 is amended as follows:

(i)the following entry 2.2.4. is inserted:‘2.2.4.For components and separate technical units, location and method of attachment of the type-approval mark(s) (if available)⁽¹⁹⁾: …’;

(ii)entry 2.5.1. is replaced by the following:‘2.5.1.Type-approval of: engine type/engine family⁽⁴⁾’;

(iii)entries 6.6. and 6.7. are replaced by the following:‘6.6.Rated speed: … min^–16.7.Maximum torque speed: … min^–1’;

(v)entry 6.19.4.2. is replaced by the following:‘6.19.3.2.Type(s): …’;

(vi)entry 7.1.1. is replaced by the following:‘7.1.1.Combustion cycle: positive ignition/compression ignition⁽⁴⁾’;

(vii)entries 8.6. and 8.7. are replaced by the following:‘8.6.Rated speed: … min^–18.7.Maximum torque speed: … min^–1’;

(viii)entry 8.12.2., including all its sub-entries, is replaced by the following:‘8.12.2.Air8.12.2.1.Blower: yes/no⁽⁴⁾8.12.2.1.1.Characteristics of the blower. …8.12.2.1.2.Drive ratio(s) (if applicable): …’;

(ix)entry 8.17., including all its sub-entries, is replaced by the following:‘8.17.Measures taken against air pollution8.17.1.Device for recycling crankcase gases: yes/no⁽⁴⁾8.17.2.Additional anti-pollution devices (if any):8.17.2.1.Catalytic converter: yes/no⁽⁴⁾8.17.2.1.1.Make: …8.17.2.1.2.Type …8.17.2.1.3.Number of catalytic converters and elements …8.17.2.1.4.Dimensions and volume of the catalytic converter(s): …8.17.2.1.5.Type of catalytic action …8.17.2.1.6.Total charge of precious metals: …8.17.2.1.7.Relative concentration: …8.17.2.1.8.Substrate (structure and material): …8.17.2.1.9.Cell density: …8.17.2.1.10.Type of casing for the catalytic converter(s): …8.17.2.1.11.Location of the catalytic converter(s) (place(s) and maximum/minimum distance(s) from engine: …8.17.2.1.12.Normal operating range: …K8.17.2.1.13.Consumable reagent (where appropriate) …8.17.2.1.13.1.Type and concentration of reagent needed for catalytic action: …8.17.2.1.13.2.Normal operational temperature range of reagent: … K8.17.2.1.13.3.International standard (if applicable): …8.17.2.1.14.NO_x sensor: yes/no⁽⁴⁾8.17.2.1.15.Oxygen sensor: yes/no⁽⁴⁾8.17.2.1.15.1.Make: …8.17.2.1.15.2.Type …8.17.2.1.15.3.Location: …8.17.2.1.16.Air injection: yes/no⁽⁴⁾8.17.2.1.16.1.Type: pulse air/air pump/other⁽⁴⁾ (if other specify: …)8.17.2.1.17.EGR: yes/no(4)8.17.2.1.17.1.Characteristics (cooled/uncooled, high pressure/low pressure, etc.): …8.17.2.1.18.Particulate trap: yes/no⁽⁴⁾8.17.2.1.18.1.Dimensions and capacity of the particulate trap: …8.17.2.1.18.2.Type and design of the particulate trap: …8.17.2.1.18.3.Location (place(s) and maximum/minimum distance(s) from engine: …8.17.2.1.18.4.Method or system of regeneration, description and/or drawing: …8.17.2.1.18.5.Normal operating temperature range: … K and pressure range: …kPa8.17.2.1.19.Other systems: yes/no⁽⁴⁾8.17.2.1.19.1.Description and operation: …’;

(x)entry 8.18., including all its sub-entries, is replaced by the following:‘8.18.Fuel feed for diesel engines8.18.1.Feed pump8.18.1.1Pressure⁽⁷⁾ … kPa or characteristic diagram: …8.18.2.Injection system8.18.2.1.Pump8.18.2.1.1.Make(s): …8.18.2.1.2.Type(s): …8.18.2.1.3.Delivery: … and … mm³⁽⁷⁾ per stroke or cycle at full injection at pump speed of: … rpm (rated) and: … rpm (maximum torque) respectively, or characteristic diagram: …8.18.2.1.3.1.Method used: on engine/on pump bench⁽⁴⁾8.18.2.2.Injection advance:8.18.2.2.1.Injection advance curve⁽⁷⁾: …8.18.2.2.2.Timing⁽⁷⁾: …8.18.2.3.Injection piping:8.18.2.3.1.Length: … mm8.18.2.3.2.Internal diameter: … mm8.18.2.4.Injector(s)8.18.2.4.1.Make(s) …8.18.2.4.2.Type(s): …8.18.2.4.3.Opening pressure⁽⁷⁾: … kPa, or characteristic diagram: …8.18.2.5.Governor8.18.2.5.1.Make(s) …8.18.2.5.2.Type(s): …8.18.2.5.3.Speed at which cut-off starts under full load⁽⁷⁾: … min^–18.18.2.5.4.Maximum no-load speed⁽⁷⁾: … min^–18.18.2.5.5.Idling speed⁽⁷⁾: … min^–18.18.2.6.Cold-start system8.18.2.6.1.Make(s): …8.18.2.6.2.Type(s): …8.18.2.6.3.Description: …’;

(xi)entry 8.19. is replaced by the following:‘8.19.Fuel feed for petrol engines’;

(f)in Appendix 7 entry 25.5.2. is replaced by the following:‘25.5.2.Rated voltage or air pressure: … V / kPa⁽⁴⁾’;

(g)in Appendix 8, the title is replaced by the following:‘Appendix 8Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) the installation of rear-view mirrors as a system’

(h)Appendix 9 is amended as follows:

(i)entry 3.3. is replaced by the following:‘3.3.Axles and wheels:’;

(ii)entry 4.1.2.1.2. is replaced by the following:‘4.1.2.1.2.In the case of a rigid drawbar or centre-axle R- or S-category vehicle indicate the vertical load on the front coupling point (S): … kg’;

(iii)entries 4.1.2.2. and 4.1.2.4. are deleted;

(iv)entry 4.1.3. is replaced by the following:‘4.1.3.Technically permissible towable mass(es) for T- or C-category vehicles for each chassis/ braking configuration of the R- or S-category vehicle (for R- and S-category vehicles, indicate the maximum permissible load(s) on the rear coupling point):R- and S category vehicleBrake | Drawbar | Rigid drawbar | Centre-axleUnbraked | … kg | … kg | … kgInertia-braked | … kg | … kg | … kgHydraulic braked | … kg | … kg | … kgPneumatic braked | … kg | … kg | … kg

(v)entry 4.1.4. is replaced by the following:‘4.1.4.Total technically permissible mass(es) of the tractor (T- or C-category vehicle) and towed vehicle (R- or S-category vehicle) combination for each chassis/braking configuration of the R- or S-category vehicle:R- and S category vehicleBrake | Drawbar | Rigid drawbar | Centre-axleUnbraked | … kg | … kg | … kgInertia-braked | … kg | … kg | … kgHydraulic braked | … kg | … kg | … kgPneumatic braked | … kg | … kg | … kg;

(vi)entries 4.1.5. to 4.1.5.3. are deleted;

(i)Appendix 10 is amended as follows:

(i)the following entry 2.2.4. is inserted:‘2.2.4.For components and separate technical units, location and method of attachment of the type-approval mark(s) (if available)⁽¹⁹⁾:…’;

(ii)entry 24.1. is replaced by the following:‘24.1.Schedule describing all projected combinations of relevant vehicle electrical/electronic systems or ESAs, body styles⁽⁶⁰⁾, variations in body material , general wiring arrangements, engine variations, left-hand/right-hand drive versions and wheelbase versions:…’;

(j)Appendix 11 is amended as follows:

(i)the following entry 2.2.4. is inserted:‘2.2.4.For components and separate technical units, location and method of attachment of the type-approval mark(s) (if available)⁽¹⁹⁾: …’;

(ii)entry 29., including all its sub-entries, is replaced by the following:‘29.BALLAST MASSES29.1.Detailed technical description (including photographs or drawings with dimensions) of the ballast masses and how they are mounted on the tractor:29.2.Number of sets of ballast masses: …29.2.1.Number of components on each set: Set 1: … Set 2:… Set …:…29.3.Mass of the components on each set: Set 1: ….kg Set 2: …kg Set … kg29.3.1.Total mass of each set: Set 1: …kg … Set 2: … kg Set … kg29.4.Total mass of ballast masses: …kg29.4.1.Distribution of these masses among the axles: … kg29.5.Material(s) and method of construction: …’;

(k)Appendix 12 is amended as follows:(i)the following entry 2.2.4. is inserted:‘2.2.4.For components and separate technical units, location and method of attachment of the type-approval mark(s) (if available)⁽¹⁹⁾: …’;

(l)Appendix 13 is amended as follows:(i)the following entry 2.2.4. is inserted:‘2.2.4.For components and separate technical units, location and method of attachment of the type-approval mark(s) (if available)⁽¹⁹⁾: …’;

(m)Appendix 14 is amended as follows:

(i)the following entry 2.2.4. is inserted:‘2.2.4.For components and separate technical units, location and method of attachment of the type-approval mark(s) (if available)⁽¹⁹⁾: …’;

(ii)entry 38.1. is replaced by the following:‘38.1.Photographs and dimensional drawings of the mechanical coupling, its installation on the vehicle and its coupling with the device installed on the towed vehicle: …’;

(iii)entry 38.5. is replaced by the following:‘38.5.Description of the mechanical coupling:Type (according to Appendix 1 of Annex XXXIV to Commission Delegated Regulation (EU) 2015/208):…Make:…Manufacturer’s type designation:…Maximum horizontal load/D-Value^(4)(44):… kg/kN⁽⁴⁾Towable mass (T) ^(4)(44):… tonnesMaximum permissible vertical load on the coupling point (S)⁽⁴⁴⁾:… kgPhotographs and scale drawings of the coupling device. These drawings shall in particular show the required dimensions in detail as well as the measurements for mounting the device.Short technical description of the coupling device specifying the type of construction and the material used.Type of TestStatic/Dynamic ⁽⁴⁾(EU) type-approval mark or -number of

—drawbar eyes, coupling heads or similar coupling devices that shall be attached to the mechanical coupling (in the case of hinged or rigid drawbars)

—type-approval mark or –number of mechanical couplings that shall be attached to the ladder frame /trailer hitch support (if restricted to certain types):’;

…’;

(n)Appendix 15 is amended as follows:

(i)entry 3.3. is replaced by the following:‘3.3.Axles and wheels:’;

(iii)entry 4.1.2.4. is deleted;

(vi)entries 4.1.5. to 4.1.5.3. are deleted;

(vii)entry 5.1.2.2. is deleted;

(viii)entries 6.6. and 6.7. are replaced by the following:‘6.6.Rated speed: … min^–16.7.Maximum torque speed: … min^–1’;

(ix)the following entries 7., 7.1. and 7.1.1. are inserted:‘7.ESSENTIAL CHARACTERISTICS OF THE ENGINE FAMILY7.1.Common parameters⁽⁵⁶⁾7.1.1.Combustion cycle: positive ignition/compression ignition⁽⁴⁾’;

(x)entry 9., including all its sub-entries, is replaced by the following:‘9.ENERGY STORAGE DEVICE(S)⁽¹¹⁾9.1.Description: battery/capacitor/flywheel/generator⁽⁴⁾9.2.Identification number: …9.3.Kind of electrochemical couple: …9.4.Energy stored9.4.1.For battery, voltage: … and capacity: … Ah in 2h9.4.2.For capacitor: … J9.4.3.For flywheel/generator(4): … J9.4.3.1.Flywheel moment of inertia: … kg m²9.4.3.1.1.Additional moment of inertia if no gear is engaged: … kg m²9.5.Charger: on-board/external/without⁽⁴⁾’;

(xi)entry 11., including all its sub-entries, is replaced by the following:‘11.DRIVE-TRAIN AND CONTROL⁽¹³⁾11.1.Brief description and schematic drawing of the vehicle drive-train and its control system (gear shift control, clutch control or any other element of drive-train):11.2.Transmission11.2.1.Brief description and schematic drawing of gear shift system(s) and its control: …11.2.2.Diagram and or drawing of the transmission system: …11.2.3.Type of transmission: mechanical/hydraulic/electric/other⁽⁴⁾ (if other specify …)11.2.4.Brief description of the electrical/electronic components (if any): …11.2.5.Location relative to the engine: …11.2.6.Method of control: …11.2.7.Transfer box: with/without⁽⁴⁾11.2.8.Type of gear shift system(s)⁽²⁴⁾: …11.3.Clutch (if any)11.3.1.Brief description and schematic drawing of the clutch and its control system:11.3.2.Maximum torque conversion: …11.4.Gear ratiosGear | Internal gearbox ratios (ratios of engine to gearbox output shaft revolutions) | Internal transfer box ratios (ratios of engine to transfer box output shaft revolutions) | Final drive ratio(s) (ratio of gearbox output shaft to driven wheel revolutions) | Total gear ratios | Ratio (engine speed/vehicle speed) for manual transmission onlyMaximum for CVT123 | | | | |Minimum for CVT*Reverse1… | | | | |11.5.Differential lock11.5.1.Differential lock: yes/no/optional⁽⁴⁾’;

(xii)entry 43.1. is replaced by the following:‘43.1.Brief description of the braking system(s) installed on the vehicle⁽⁵⁵⁾: …’;

(xiii)entry 43.3. is deleted;

(xiv)entry 43.6., including all its sub-entries, is replaced by the following:‘43.6.Towed vehicle braking devices43.6.1.Towed vehicle braking control system technology: Hydraulic / Pneumatic / Electric/None⁽⁴⁾43.6.2.Towed vehicle-brake actuating device (description, characteristics): …43.6.3.Description of the connectors, couplings and safety devices (including drawings, sketches and the identification of any electronic parts): …43.6.4.Connections type: Single line/Two-lines/None⁽⁴⁾43.6.4.1.Supply pressure Hydraulic: Single line: … kPa Two lines: … kPa43.6.4.2.Supply pressure Pneumatic: Two lines: … kPa43.6.5.Presence of ISO 7638:2003 connector⁽¹⁵⁾: … yes/no⁽⁴⁾’;

(xv)the following entries are added:‘43.ATOWED VEHICLE AXLE AND BRAKE INFORMATION DOCUMENT WITH RESPECT TO THE ALTERNATIVE TYPE I AND TYPE III PROCEDURE43.A.1.General43.A.1.1.Name and address of axle or vehicle manufacturer:43.A.2.Axle data43.A.2.1.Manufacturer (name and address): …43.A.2.2.Type/variant: …43.A.2.3.Axle identifier: ID1- …43.A.2.4.Test axle load (Fe): … daN43.A.2.5.Wheel and brake data according to the following figures 1A and 1B43.A.3.Brake43.A.3.1.General information43.A.3.1.1.Make:43.A.3.1.2.Manufacturer (name and address):43.A.3.1.3.Type of brake (e.g. drum / disc):43.A.3.1.3.1.Variant (e.g. S-cam, single wedge etc.):43.A.3.1.4.Brake identifier: ID2-43.A.3.1.5.Brake data according to the figures 2A and 2B:43.A.3.2.Drum brake data43.A.3.2.1.Brake adjustment device (external/integrated): …43.A.3.2.2.Declared maximum brake input torque C_max: … Nm43.A.3.2.3.Mechanical efficiency: η =…43.A.3.2.4.Declared brake input threshold torque C_0,dec: … Nm43.A.3.2.5.Effective length of the cam shaft: … mm43.A.3.3.Brake drum43.A.3.3.1.Max diameter of friction surface (wear limit) … mm43.A.3.3.2.Base material: …43.A.3.3.3.Declared mass: … kg43.A.3.3.4.Nominal mass: … kg43.A.3.4.Brake lining43.A.3.4.1.Manufacturer and address …43.A.3.4.2.Make …43.A.3.4.3.Type …43.A.3.4.4.Identification (type identification on lining) …43.A.3.4.5.Minimum thickness (wear limit) … mm43.A.3.4.6.Method of attaching friction material to brake shoe: …43.A.3.4.6.1.… Worst case of attachment (in the case of more than one):43.A.3.5.Disc brake data43.A.3.5.1.Connection type to the axle (axial, radial, integrated, etc.): …43.A.3.5.2.Brake adjustment device (external/integrated): …43.A.3.5.3.Max. actuation stroke: … mm43.A.3.5.4.Declared maximum input force Th_Amax: … daN43.A.3.5.4.1Cmax = Th_Amax · l_e : … Nm43.A.3.5.5.Friction radius: r_e = … mm43.A.3.5.6.Lever length: l_e = … mm43.A.3.5.7.Input/output ratio (l_e/e_e): i = …43.A.3.5.8.Mechanical efficiency: η = …43.A.3.5.9.Declared brake input threshold force Th_A0,dec: … N43.A.3.5.9.1.C_0,dec = Th_A0,dec · l_e : … Nm43.A.3.5.10.Minimum rotor thickness (wear limit): … mm43.A.3.6.Brake disc data …43.A.3.6.1.Disc type description: …43.A.3.6.2.Connection/mounting to the hub: …43.A.3.6.3.Ventilation (yes/no): …43.A.3.6.4.Declared mass: … kg43.A.3.6.5.Nominal mass: … kg43.A.3.6.6.Declared external diameter: … mm43.A.3.6.7.Minimum external diameter: … mm43.A.3.6.8.Inner diameter of friction ring: … mm43.A.3.6.9.Width of ventilation channel (if appl.): … mm43.A.3.6.10.Base material: …43.A.3.7.Brake pad data …43.A.3.7.1.Manufacturer and address: …43.A.3.7.2.Make:43.A.3.7.3.Type: …43.A.3.7.4.Identification (type identification on pad back plate): …43.A.3.7.5.Minimum thickness (wear limit): … mm43.A.3.7.6.Method of attaching friction material to pad back plate: …43.A.3.7.6.1.Worst case of attachment (in the case of more than one): …Figure 1AFigure 1BFigure 2AFigure 2Bxe (mm) | ae (mm) | he (mm) | ce (mm) | de (mm) | ee (mm) | α0e | α1e | be (mm) | re (mm) | Ae (cm2) | S1e (mm) | S2e (mm) | S3e (mm);| | | | | | | | | | | | |

(o)Appendix 19 is amended as follows:

(i)the following entry 2.2.4. is inserted:‘2.2.4.For components and separate technical units, location and method of attachment of the type-approval mark(s) (if available)⁽¹⁹⁾: …’;

(ii)entry 46.2.1. is replaced by the following:‘46.2.1.In the case of roll bar: foldable/not foldable⁽⁴⁾’;

(iii)entry 46.2.2., including all its sub-entries, is replaced by the following:‘46.2.2.In the case of foldable roll bar:46.2.2.1.Folding operation: non-assisted / partially assisted / fully assisted⁽⁴⁾46.2.2.2.In case of non-assisted or partially assisted folding operation:46.2.2.2.1.Hand-operated foldable ROPS: with tools/ without tools⁽⁴⁾46.2.2.2.2.Photographs and detailed technical drawings showing the grasping area and a lateral and top view of the accessible zones. Dimensions and maximum forces for actuating the ROPS must figure on the drawings: …46.2.2.3.In case of partially assisted or fully assisted folding operation, brief description of the assistance devices as well as of their control devices, if any, and their location: …46.2.2.4.Locking mechanism: manual/automatic⁽⁴⁾46.2.2.4.1.For manual locking mechanisms, brief description of the locking mechanism and of its ergonomic design to avoid pinching or shearing hazards and to limit the force required for its operation: …46.2.2.4.2.For automatic locking mechanisms,46.2.2.4.2.1.Brief description of the locking mechanism, its control devices, if any, and their location: …46.2.2.4.2.2.Manufacturers' certificate set out in Note 2 of point 5.5. of Part B3 of Annex IX to Commission Delegated Regulation (EU) No 1322/2014: yes/no⁽⁴⁾’;

(p)in Appendix 20, the following entry 2.2.4. is inserted:‘2.2.4.For components and separate technical units, location and method of attachment of the type-approval mark(s) (if available)⁽¹⁹⁾: …’;

(q)Appendix 21 is amended as follows:

(i)the following entry 2.2.4. is inserted:‘2.2.4.For components and separate technical units, location and method of attachment of the type-approval mark(s) (if available)⁽¹⁹⁾: …’;

(ii)entry 49.4.1. is replaced by the following:‘49.4.1.Position of the driving seat: left/right/centre⁽⁴⁾’;

(r)Appendix 22 is amended as follows:

(i)the following entry 2.2.4. is inserted:‘2.2.4.For components and separate technical units, location and method of attachment of the type-approval mark(s) (if available)⁽¹⁹⁾: …’;

(ii)entry 54.3. is replaced by the following:‘54.3.Number and position of safety belts and seats on which they can be used, please fill out table below:Safety belt configuration and associated information| | | Complete EU type-approval mark / ECE type-approval mark | Variant, if applicable | Belt adjustment device for height (indicate yes/no/optional)Driver's seat | | L | | |C | | |R | | |Passenger seat1 | | L | | |C | | |R | | |Passenger seat… | | L | | |C | | |R | | |

(r)Appendix 24 is replaced by the following:

(s)in Appendix 23, the following entry 2.2.4. is inserted:‘2.2.4.For components and separate technical units, location and method of attachment of the type-approval mark(s) (if available)⁽¹⁹⁾: …’;

(s)the explanatory notes relating to the information document are amended as follows:

(i)explanatory note (9) is replaced by the following:‘(9)Indicate fuel type by the following codes:PpetrolB5dieselE5petrol E5Mmixture (for two stroke engines)Oother.’

(ii)the following explanatory note (11) is inserted:‘(11)Excluding SLI batteries that supply electric energy for starting, lighting and ignition.’

(iii)explanatory note (14) is replaced by the following:‘(14)‘A’for a three-point belt;‘B’for a lap belt;‘S’for special types of belt (in this case provide specific information on the nature of these types under observation in entry 53.4.1.);‘Ar’, ‘Br’ or‘Sr’for a belt incorporating an inertia reel retractor;‘Are’, ‘Bre’ and ‘Sre’for a belt equipped with an inertia reel retractor and an energy-absorption device on at least one anchorage.’

(iv)the following explanatory notes (15) and (16) are inserted:‘(15)Only applicable to T- and C-category vehicles authorized to tow R- or S-category vehicles if fitted with a hydraulic energy storage device.’‘(16)Indicate the maximum towable mass on the lower link arms of the rear three-point lifting mechanism or the rear three-point lifting mechanism itself, as declared by the manufacturer.’

(v)explanatory note (24) is replaced by the following:‘(24)Indicate the type of gear shift system(s) by the following codes:AautomaticM1manualM2manual automatedCcontinuous variable transmission (CVT)Wwheel-hub engineOother (indicate…)’;

(vi)explanatory note (26) is replaced by the following:‘(26)Indicate the layout of the cylinders by following codes:LIin lineVin VOopposed-cylinder engineSsingle-cylinder engineRrotatory piston engine. ’;

(vii)explanatory note (48) is replaced by the following:‘(48)For R- and S-category vehicles indicate the overhang of the front coupling point. ’;

(viii)explanatory note (49) is replaced by the following:‘(49)For engines indicate the information relative to the engine type or the engine family type, as applicable without the type-approval extension number.’

(ix)explanatory note (52) is replaced by the following:‘(52)When the tractor is fitted with different optional seats or has a reversible driver’s position (reversible seat and steering wheel), the dimensions in relation to the seat index points (SIP 1, SIP 2, etc.) shall be measured for each case.’

Annex I to Implementing Regulation (EU) 2015/504 is amended as follows:

Annex II

In Annex II to Implementing Regulation (EU) 2015/504, in the explanatory notes relating to Annex II, explanatory note (4) is replaced by the following:

‘(4)For engines indicate the information relative to the engine type or the engine family type, as applicable without the type-approval extension number.’

III

(1)Section 2 is amended as follows:

(a)Model 1 is amended as follows:

(i)under the heading ‘General construction characteristics’, entry 3.4.4. is replaced by the following:‘3.4.4.Steering by^(33a):

—changing the speed between the left-hand side and right-hand side track trains: yes/no⁽¹⁾

—pivoting of two opposite or all four track trains: yes/no⁽¹⁾

—articulation of the front and rear part of the vehicle around a central vertical axis: yes/no⁽¹⁾

—articulation of the front and rear part of the vehicle around a central vertical axis and changing the direction of the wheels on the wheeled axle: yes/no⁽¹⁾’;

(ii)under the heading ‘General construction characteristics’, entries 37.2. and 3.4.2. (Type of chassis) are deleted;

(iii)under the heading ‘Constructions characteristics for special purposes’, entry 58.3. is replaced by the following:‘58.3.Vehicle equipped with a cab classified for protection against hazardous substances of category: 2/3/4^(1)(35) and a Dust filter/ Aerosol filter/ Vapour filter^(1)(36) with regard to protection against hazardous substances⁽³³ⁿ⁾.’;

(iv)under the heading ‘Masses’, entry 4.1.2.2. is replaced by the following:‘4.1.2.2.Mass(es) and tyre(s)Tyre combi-nation No | Axle No | Tyre dimension incl load capacity index & speed category symbol | Rolling radius(1) [mm] | Tyre Load rating per tyre [kg] | Maximum permissible mass per axle [kg] | Maximum permissible mass of the vehicle [kg] | Maximum permissible vertical load on the coupling point [kg] | Track width [mm]Minimum | Maximum1 | 1 | … | | … | … | … | … | … | …2 | … | | … | … | … | … | … | …… | … | | … | … | … | … | … | …2 | 1 | … | | … | … | … | … | … | …| 2 | … | | … | … | … | … | … | …| … | … | | … | … | … | … | … | …… | 1 | … | | … | … | … | … | … | …| 2 | … | | … | … | … | … | … | …| … | … | | … | … | … | … | … | …

(v)under the heading ‘Masses’, entries 4.1.3. and 4.1.4. are replaced by the following:‘4.1.3.Technically permissible towable mass(es) for each chassis/ braking configuration of the R- or S-category vehicle:R- and S category vehicleBrake | Drawbar | Rigid drawbar | Centre-axleUnbraked | … kg | … kg | … kgInertia-braked | … kg | … kg | … kgHydraulic braked | … kg | … kg | … kgPneumatic braked | … kg | … kg | … kg4.1.4.Total technically permissible mass(es) of the tractor (T- or C-category vehicle) and towed vehicle (R- or S-category vehicle) combination for each chassis/braking configuration of the R- or S-category vehicle:R- and S category vehicleBrake | Drawbar | Rigid drawbar | Centre-axleUnbraked | … kg | … kg | … kgInertia-braked | … kg | … kg | … kgHydraulic braked | … kg | … kg | … kgPneumatic braked | … kg | … kg | … kg;

(vi)under the heading ‘Masses’, entry 4.1.5.1. is deleted;

(vii)all entries under the heading ‘Ballast masses’ are replaced by the following:‘29.2.Number of sets of ballast masses: …29.2.1.Number of components on each set: Set 1: …Set 2: …Set …29.4.Total mass of ballast masses: …kg’;

(viii)under the heading ‘Main dimensions’, entry 4.2.1.3. is replaced by the following:‘4.2.1.3.Height (in running order)⁽³³⁾: maximum … mm minimum … mm’;

(ix)under the heading ‘Main dimensions’, entry 4.2.2.8. is replaced by the following:‘4.2.2.8.Track width⁽¹⁷⁾: Maximum: Axle 1 … mm Axle 2 … mm Axle … mmMinimum: Axle 1 … mm Axle 2 … mm Axle … mm’;

(x)under the heading ‘General powertrain characteristics’, entry 5.1.1.3. is replaced by the following:‘5.1.1.1.Declared maximum design vehicle speed: … km/h ’;

(xi)under the heading ‘General powertrain characteristics’, entry 5.1.2.2. is replaced by the following entry 5.1.2.1.:‘5.1.2.1.Declared rearward maximum design vehicle speed: … km/h’;

(xii)under the heading ‘Engine’, entry 2.2.2. is replaced by the following:‘2.2.2.Type-approval number without extension: …’;

(xiii)under the heading ‘Engine’, entry 2.5.4.1. is deleted;

(xiv)under the heading ‘Engine’, the following entry 7.1.1. is added:‘7.1.1.Combustion cycle: positive ignition/compression ignition⁽¹⁾’;

(xv)under the heading ‘Gearbox’, entries 11.4.1., 11.5. and 11.5.1. are deleted;

(xvi)under the heading ‘Gearbox’, the following entry 11.2.8. is added:‘11.2.8.Type of gear shift system(s)⁽²²⁾: …’;

(xvii)all entries under the heading ‘Braking’ are replaced by the following:‘43.4.6.Electronic braking system: yes/no/optional⁽¹⁾43.5.1.Braking transmission : mechanical/ hydrostatic without power assistance / power – assisted / fully powered transmission⁽¹⁾43.5.3.Locking of left and right braking controls: …43.6.1.Towed vehicle braking control system technology: Hydraulic / Pneumatic / Electric/None⁽¹⁾43.6.4.Connections type: Single line/Two-lines/None⁽¹⁾43.6.4.1.Supply pressure Hydraulic: Single line: … kPa Two lines: … kPa43.6.4.2.Supply pressure Pneumatic: …Two lines: … kPa43.6.5.Presence of ISO 7638:2003 connector^(33p): yes/no⁽¹⁾’;

(xviii)under the heading ‘Rollover protective structure (ROPS)’, entry 46.1. is replaced by the following:‘46.1.Equipment of ROPS: compulsory/optional/standard⁽¹⁾’;

(xix)under the heading ‘Rollover protective structure (ROPS)’, entries 46.2.1. and 46.2.2. are replaced by the following:‘46.2.1.In the case of roll bar: foldable/not foldable⁽¹⁾46.2.2.In the case of foldable roll bar:46.2.2.1.Folding operation: non-assisted / partially assisted / fully assisted⁽¹⁾;46.2.2.2.1.Hand-operated foldable ROPS: with tools/ without tools⁽⁴⁾46.2.2.4.Locking mechanism: manual/automatic⁽¹⁾’;

(xx)under the heading ‘Seating positions (saddles and seats)’, entry 49.5.1. is replaced by the following:‘49.5.1.Number of passenger seats:…’;

(xxi)the heading ‘Load platform(s)’, including all entries under that heading, is replaced by the following:‘Load platform(s)^(33d)33.1.1.Length of the load platform(s): … mm33.1.2.Width of load platform(s): … mm33.1.3.Height of load platform(s) above the ground: … mm33.2.Safe load carrying capacity of load platform declared by manufacturer: … kg’;

(xxii)the heading ‘Lighting and light-signalling devices’ and entry 21.1. are deleted;

(xxiii)under the heading ‘Mechanical couplings’, entry 38.4. is replaced by the following:‘38.3.Rear mechanical couplingType (according to Appendix 1 of Annex XXXIV to Commission Delegated Regulation (EU) 2015/208): | … | … | …Make: | … | … | …Manufacturer’s type designation: | … | … | …(EU) type-approval mark or -number: | … | … | …Maximum horizontal load/D-Value(4)(44): | … kg/kN(4) | … kg/kN(4) | … kg/kN(4)Towable mass (T) (4)(44): | … tonnes | … tonnes | … tonnesMaximum permissible vertical load on the coupling point(44): | … kg | … kg | … kgPosition of coupling point(62) | height above ground, | minimum | … mm | … mm | … mmmaximum | … mm | … mm | … mmdistance from vertical plane passing through the axis of the rear axle | minimum | … mm | … mm | … mmmaximum | … mm | … mm | … mm;

(xxiv)under the heading ‘Three-point lifting mechanism’, the following entry 39.2. is added:‘39.2.Maximum towable mass⁽²³⁾: … kg’;

(xxv)all entries under the heading ‘Power take-off(s)’ are replaced by the following:‘51.2.Main PTO: Position: front/rear/other⁽¹⁾ (if other specify: …)51.3.Secondary PTO⁽³³⁾: Position: front/rear/other⁽¹⁾ (if other specify:…)51.2.3.Optional⁽³³⁾: Power at the power take-off (PTO) at the rated speed(s) [in accordance with OECD Code 2⁽²⁶⁾ or ISO 789-1:1990 (Agricultural tractors — Test procedures — Part 1: Power tests for power take-off)]Rated speed PTO(min-1) | Corresponding engine speed(min-1) | Power(kW)Main PTO | Secondary PTO (33) | Main PTO | Secondary PTO (33)1-540 | … | … | … | …2-1 000 | … | … | … | …540E | … | … | … | …1000E; | … | … | … | …

(b)Model 2 is amended as follows:

(i)under the heading ‘Masses’, entry 4.1.2.1.2. is replaced by the following:‘4.1.2.1.2.Vertical load on the front coupling point (S)^(33h):’…kg … kg

(ii)under the heading ‘Masses’, entry 4.1.2.2. is replaced by the following:‘4.1.2.2.Mass(es) and tyre(s)Tyre combi-nation No | Axle No | Tyre dimension incl load capacity index & speed category symbol | Rolling radius(1) [mm] | Tyre Load rating per tyre [kg] | Maximum permissible mass per axle [kg] | Maximum permissible mass of the vehicle [kg] | Maximum permissible vertical load on the coupling point [kg] | Track width [mm]Minimum | Maximum1 | 1 | … | | … | … | … | … | … | …2 | … | | … | … | … | … | … | …… | … | | … | … | … | … | … | …2 | 1 | … | | … | … | … | … | … | …| 2 | … | | … | … | … | … | … | …| … | … | | … | … | … | … | … | …… | 1 | … | | … | … | … | … | … | …| 2 | … | | … | … | … | … | … | …| … | … | | … | … | … | … | … | …

(iii)under the heading ‘Masses’, entry 4.1.3. is replaced by the following:‘4.1.3.Maximum permissible load(s) on the rear coupling point for towing a second R- or S-category vehicle for each chassis/ braking configuration of the mentioned second vehicle^(33e):R- and S category vehicleBrake | Drawbar | Rigid drawbar | Centre-axleUnbraked | .… kg | .… kg | .… kgInertia-braked | .… kg | .… kg | .… kgHydraulic braked | .… kg | .… kg | .… kgPneumatic braked | .… kg | .… kg | .… kg;

(iv)under the heading ‘Masses’, entry 4.1.5.2. is deleted;

(v)under the heading ‘Main dimensions’, entry 4.2.1.3. is replaced by the following:‘4.2.1.3.Height (in running order)⁽³³⁾: maximum… mm … minimum … mm’;

(vi)under the heading ‘Main dimensions’, entry 4.2.2.8. is replaced by the following:‘4.2.2.8.Track width⁽¹⁷⁾: Maximum: Axle 1 … mm Axle 2 … mm Axle … mmMinimum: Axle 1 … mm Axle 2 … mm Axle … mm’;

(vii)all entries under the heading ‘Braking’ are replaced by the following:‘43.4.6.Electronic braking system: yes/no/optional⁽¹⁾43.5.1.Braking transmission: mechanical/ hydrostatic without power assistance / power – assisted / fully powered transmission⁽¹⁾43.6.1.Towed vehicle braking control system technology: Hydraulic / Pneumatic / Electric/None⁽¹⁾43.6.4.Connections type: Single line/Two-lines/None⁽¹⁾43.6.4.1.Supply pressure Hydraulic: …Single line: … kPa … Two lines: … kPa43.6.4.2.Supply pressure Pneumatic: …Two lines: … kPa’;

(viii)the heading ‘Load platform(s)’, including all entries under that heading, are replaced by the following:‘Load platform(s)^(33d)33.1.1.Length of the load platform(s):… mm33.1.2.Width of load platform(s):… mm33.1.3.Height of load platform(s) above the ground:… mm33.2.Safe load carrying capacity of load platform declared by manufacturer: … kg’;

(ix)the heading ‘Lighting and light-signalling devices’ and entry 21.1. are deleted;

(c)the explanatory notes relating to Appendix 1 are amended as follows:

(i)explanatory notes (20) to (23) are replaced by the following:‘(20)Indicate fuel type by the following codes:PpetrolB5dieselE5petrol E5Mmixture (for two stroke engines)Oother.(21)Indicate the layout of the cylinders by following codes:LIin lineVin VOopposed-cylinder engineSsingle-cylinder engineRrotatory piston engine.(22)Indicate the type of gear shift system(s) by the following codes:AautomaticM1manualM2manual automatedCcontinuous variable transmission (CVT)Wwheel-hub engineOother (indicate…)(23)Indicate the maximum towable mass on the lower link arms of the rear three-point lifting mechanism or the rear three-point lifting mechanism itself, as declared by the manufacturer.’

(ii)explanatory note (24) is deleted;

(iii)explanatory note (33) is replaced by the following:‘(33)Delete this entry of the certificate of conformity if not applicable to the vehicle.’

(iv)explanatory note (33d) is replaced by the following:‘(33d)Only applicable to vehicles fitted with load platform(s).’

(v)the following explanatory note (33p) is inserted:‘(33p)Only applicable to T- and C-category vehicles authorized to tow R- or S-category vehicles if fitted with a hydraulic energy storage device.’

(vi)explanatory note (37) is deleted.

Appendix 1 to Annex III to Implementing Regulation (EU) 2015/504 is amended as follows:

Annex IV

(1)point 2.1.1. is replaced by the following:‘2.1.1.The information on the plate shall be clearly legible, indelible and shall contain the following information in the order given below and in accordance with one of the two alternative models set out in Appendix 1:’

(2)point 2.1.1.8. is replaced by the following:‘2.1.1.8.Technically permissible towable mass(es) for each chassis/ braking configuration of the towed R- or S-category vehicle in accordance with entry 4.1.3 of the information document data entries laid down in Part B of Annex I to this Regulation⁽²⁾, in the following format: “B-1” unbraked, “B-2” inertia braked, “B-3” hydraulic braked, “B-4” pneumatic braked, “T-1” drawbar, “T-2” rigid drawbar, “T-3” centre-axle;’

(3)point 4.1.1.8. is replaced by the following:‘4.2.1.8.Technically permissible towable mass(es) for each chassis/ braking configuration of the towed R- or S-category vehicle in accordance with entry 4.1.3 of the information document data entries laid down in Part B of Annex I to this Regulation⁽²⁾, in the following format: “B-1” unbraked, “B-2” inertia braked, “B-3” hydraulic braked, “B-4” pneumatic braked, “T-1” drawbar, “T-2” rigid drawbar, “T-3” centre-axle;’

(4)Appendix 1 is replaced by the following:

Annex IV to Implementing Regulation (EU) 2015/504 is amended as follows:

Annex V

(1)in Appendix 1, in section III, entry 2.1. is replaced by the following:‘2.1.The approval is granted in accordance with Article 35 of Regulation (EU) No 167/2013 and the validity of the approval is thus limited to dd/mm/yyyy⁽⁶⁾.’

(2)Appendix 2 is amended as follows:

(a)in section III, entry 4.1. is replaced by the following:‘4.1.The approval is granted in accordance with Article 35 of Regulation (EU) No 167/2013 and its validity is thus limited to dd/mm/yyyy⁽⁶⁾.’

(b)Section 2 is replaced by the following:‘SECTION 2This EU type-approval concerns incomplete and completed vehicles, variants or versions.1.Previous stage(s) approval(s) for the vehicles.Stage | EU type-approval number | Dated | Applicable to (as appropriate) | Variants and versions which are complete or completed (as appropriate)(9)1(base vehicle) | | | |2 | | | |2.List of requirements applicable to the approved incomplete vehicle type, variant, taking account of the scope and latest amendment to each of the regulatory acts listed below⁽¹⁰⁾.Item | Subject | Regulatory act reference | As amended by and/or stage of implementation | Applicable to variants| | | |

(3)in Appendix 4, in section III, entry 2.1. is replaced by the following:‘2.1.The approval is granted in accordance with Article 35 of Regulation (EU) No 167/2013 and the validity of the approval is thus limited to dd/mm/yyyy⁽⁶⁾.’

(4)in Appendix 5, in section III, entry 2.1. is replaced by the following:‘2.1.The approval is granted in accordance with Article 35 of Regulation (EU) No 167/2013 and the validity of the approval is thus limited to dd/mm/yyyy⁽⁴⁾.’

Annex V to Implementing Regulation (EU) 2015/504 is amended as follows:

Annex VI

In Annex VII to Implementing Regulation (EU) 2015/504, in Appendix 1, point 4 is replaced by the following:

‘4.Braking performanceMeasured according to Annex II to Commission Delegated Regulation (EU) 2015/68, as last amended by Commission Delegated Regulation (EU) …/…⁽¹⁾⁽³⁾Table I| Axles of the vehicle | Reference axlesStatic mass (P)1 | Braking force needed at wheels | Speed | Test mass (Pe) | Braking force developed at wheels | Speedkg | N | km/h | kg | N | km/hAxle 1Axle 2Axle 3Axle 4 | | | | | |Table IITotal mass of the vehicle submitted for approval … kgBraking force needed at wheels … NRetarding torque needed at main shaft of endurance braking system … NmRetarding torque obtained at main shaft of endurance braking system (according to diagram) … NmTable IIIReference axle … Report No. … Date …… (copy attached)| Type-I | Type-IIIBraking force per axle (N)(See point 4.2.1. of Appendix 1 to Annex VII to Regulation (EU) 2015/68) | |Axle 1Axle 2Axle 3 | T1 = … % FeT2 = … % FeT3 = … % Fe | T1 = … % FeT2 = … % FeT3 = … % FePredicted actuator stroke (mm)(See point 4.3.1.1. of Appendix 1 to Annex VII to Regulation (EU) 2015/68) | |Axle 1Axle 2Axle 3 | s1 = …s2 = …s3 = … | s1 = …s2 = …s3 = …Average thrust output (N)(See point 4.3.1.2. of Appendix 1 to Annex VII to Regulation (EU) 2015/68) | |Axle 1Axle 2Axle 3 | ThA1 = …ThA2 = …ThA3 = … | ThA1 = …ThA2 = …ThA3 = …Braking performance (N)(See point 4.3.1.4. of Appendix 1 to Annex VII to Regulation (EU) 2015/68) | |Axle 1Axle 2Axle 3 | T1 = …T2 = …T3 = … | T1 = …T2 = …T3 = …Type-0 subject towed vehicle test result (E) | Type-I hot(predicted) | Type-III hot(predicted)Braking performance of vehicle(See points 2.3.3, 2.4.3 and 2.5.5 of Annex II to Regulation (EU) 2015/68) | | | .

VII

(1)Point 1.1. is replaced by the following:

1.1.For each of the regulatory acts listed in Annex I to Regulation (EU) No 167/2013, the template of the test reports shall be drawn up by the technical service in accordance with its rules of good practice.’

(2)the following points 3.3. to 3.4.2. are added:‘3.3.Test reports on brakingThe models of the test reports for braking are set out in Appendices 1 to5.3.4.Additional information to be stated in model test report form for the alternative procedures for Type-I and Type-III tests for towed vehicle brakes (Annex VII, Appendix 1 to Regulation (EU) 2015/68)set out in Appendix 13.4.1.Test report numberThe test report number consists of two parts: a base part and a suffix which identifies the issue level of the test report.3.4.1.1.The base part, consisting of a maximum of 20 characters, and suffix shall be clearly separated from each other using e.g. a dot or slash.3.4.1.2.The base part of the test report number shall only cover brakes with the same brake identifier and the same brake factor.3.4.2.Test codeIn addition to the test report number a “test code” consisting of up to eight characters (e.g. ABC123) shall indicate the test results applicable to the identifiers and the test specimen, which is described by the details given in point 3.7. of Appendix 1 to Annex VII to Regulation (EU) 2015/68.’

(3)the following Appendices 1 to 5 are added:‘ ’

Annex VIII to Implementing Regulation (EU) 2015/504 is amended as follows:

Appendix 1

Model test report form for the alternative procedures for Type-I and Type-III tests for towed vehicle brakes (Annex VII, Appendix 1 to Regulation (EU) 2015/68)

1.General …

1.1.Axle manufacturer (name and address): …

1.1.1.Make of axle manufacturer: …

1.2.Brake manufacturer (name and address): …

1.2.1.Brake identifier ID2-: …

1.2.2.Automatic brake adjustment device: integrated/non-integrated^note

1.3.Manufacturer's Information Document:

2.Test RecordThe following data has to be recorded for each test:

2.1.Test code: …

2.2.Test specimen: (precise identification of the variant tested related to the Manufacturer's Information Document.)

2.2.1.Axle

2.2.1.1.Axle identifier: ID1- …

2.2.1.2.Identification of tested axle: …

2.2.1.3.Test axle load (Fe identifier): ID3- … daN

2.2.2.Brake

2.2.2.1.Brake identifier: ID2- …

2.2.2.2.Identification of tested brake: …

2.2.2.3.Maximum stroke capability of the brake^note: …

2.2.2.4.Effective length of the cam shaft³: …

2.2.2.5.Material variation as per point 3.8 (m) of Appendix 1 to Annex VII to Regulation (EU) 2015/68: …

2.2.2.6.Brake drum / disc^note …

2.2.2.6.1.Actual test mass of disc / drum^note: …

2.2.2.6.2.Nominal external diameter of disc^note: …

2.2.2.6.3.Type of cooling of the disc ventilated/non-ventilated^note

2.2.2.6.4.With or without integrated hub^note

2.2.2.6.5.Disc with integrated drum – with or without parking brake function^note^note

2.2.2.6.6.Geometric relationship between disc friction surfaces and disc mounting: …

2.2.2.6.7.Base material: …

2.2.2.7.Brake lining or pad^note

2.2.2.7.1.Manufacturer: …

2.2.2.7.2.Make: …

2.2.2.7.3.Type: …

2.2.2.7.4.Method of attachment of the lining / pad on the brake shoe / back plate^note: …

2.2.2.7.5.Thickness of back plate, weight of shoes or other describing information (Manufacturer's Information Document)^note: …

2.2.2.7.6.Base material of brake shoe / back plate^note: …

2.2.3.Automatic brake adjustment device (not applicable in the case of integrated automatic brake adjustment device)^note

2.2.3.1.Manufacturer (name and address): …

2.2.3.2.Make: …

2.2.3.3.Type: …

2.2.3.4.Version: …

2.2.4.Wheel(s) (dimensions see Figures 1A and 1B in the information document of towed vehicle axle and brake with respect to the alternative procedures for Type I and Type III tests)

2.2.4.1.Reference tyre rolling radius (R_e) at test axle load (F_e): …

2.2.5.Lever length le: …

2.2.6.Brake actuator

2.2.6.1.Manufacturer: …

2.2.6.2.Make: …

2.2.6.3.Type: …

2.2.6.4.(Test) Identification number: …

2.3.Test results (corrected to take account of rolling resistance of 0,01·F_e and 0,02·F_e respectively)

2.3.1.In the case of vehicles of categories

—R1, R2, S1

—‘R3a/R4a/S2a’^note

—‘R3b/R4b/S2b’ where the sum of the technically permissible masses per axle does not exceed 10000 kg^note

Depending on the maximum design speed and assumed rolling resistance of 0,01 or 0,02 in the following Tables A to C apply:

2.3.1.1Considered rolling resistance coefficient R = 0,01 (covering also towed vehicles specified in point 2.3.1. above with a maximum design speed exceeding 40 km/h)Table AApplicable for all towed vehicle as specified in paragraph 2.3.1 aboveTest type | 0 | IAppendix 1 to Annex VII of Regulation (EU) 2015/68, point: | 3.5.1.4. | 3.5.2.2. or 3.5.2.3. | 3.5.2.4.Test speed | 40 | 40 | 40Brake actuator pressure pe | | — |Braking time | — | 2,55 | —Brake force developed Te | | |Brake efficiency Te/Fe | | |Actuator stroke se | | — |Brake input torque Ce | | — |Brake input threshold torque C0,e | | |

2.3.1.2Considered rolling resistance coefficient R = 0,02 (covering towed vehicles Ra and Sa specified in point 2.3.1. above with a maximum design speed not exceeding 40 km/h)Table BAlternative test procedure applicable for all towed vehicle of categories Ra and SaTest type | 0 | IAnnex VII, Appendix 2, paragraph: | 3.5.1.4. | 3.5.2.2. or 3.5.2.3. | 3.5.2.4.Test speed | 40 | 40 | 40Brake actuator pressure pe | | — |Braking time | — | 2,55 | —Brake force developed Te | | |Brake efficiency Te/Fe | | |Actuator stroke se | | — |Brake input torque Ce | | — |Brake input threshold torque C0,e | | |

2.3.1.3Considered rolling resistance coefficient R = 0,02 (covering towed vehicles Ra and Sa specified in point 2.3.1. above with a maximum design speed not exceeding 30 km/h)Table CAlternative test procedure in the case of towed vehicle with vmax ≤ 30 km/hTest type | 0 | IAppendix 1 to Annex VII of Regulation (EU) 2015/68, point: | 3.5.1.4. | 3.5.2.2. or 3.5.2.3. | 3.5.2.4.Test speed | 30 | 30 | 30Brake actuator pressure pe | | — |Braking time | — | 3,90 | —Brake force developed Te | | |Brake efficiency Te/Fe | | |Actuator stroke se | | — |Brake input torque Ce | | — |Brake input threshold torque C0,e | | |

2.3.2.In the case of vehicles of categories

—‘R3a/R4a/S2a’^note

—‘R3b/R4b/S2b’ where the sum of the technically permissible masses per axle does not exceed 10000 kg^note

—R3b/R4b/S2b’ where the sum of the technically permissible masses per axle exceeds 10000 kg

Test type | 0 | IIIAppendix 1 to Annex VII of Regulation (EU) 2015/68, point: | 3.5.1.4. | 3.5.3.1. | 3.5.3.2.Test speed initial km/h | 60 | | 60Test speed finalkm/h | | |Brake actuator pressure pe | | — |Number of brake applications - | — | 20 | —Duration of braking cycle s | — | 60 | —Brake force developed Te daN | | |Brake efficiency Te/Fe - | | |Actuator stroke se mm | | — |Brake input torque Ce Nm | | — |Brake input threshold torque C0,e Nm | | — |

3.Application rangeThe application range specifies the axle/brake variants that are covered in this test report, by showing which variables are covered by the individual test codes.

4.This test has been carried out and the results reported in accordance with Appendix 1 to Annex VII to Regulation (EU) 2015/68.At the end of the test described in point 3.6. of Appendix 1 to Annex VII of Regulation (EU) 2015/68, the requirements of point 2.2.2.8.1. of Annex I to Regulation (EU) 2015/68 were deemed to be fulfilled / not fulfilled^note.Technical Service^note carrying out the testSigned: … Date: …

5.Approval Authority^noteSigned: … Date: …

Test Report No. …

Base part: ID4- …

Suffix: …

Appendix 2

Model test report form for an alternative automatic brake adjustment device as prescribed in point 3.7.5. of Appendix 1 to Annex VII to Regulation (EU) 2015/68

1.Identification

1.1.Axle:Make: …Type: …Model: …Test axle load (F_e identifier): ID3- … daNTest Report No. for the alternative procedures for Type-I and Type-III tests for towed vehicle brakes (Annex VII, Appendix I to Regulation (EU) 2015/68) …

1.2.Brake:Make: …Type: …Model: …Brake lining: …Make/Type: …

1.3.Actuation: …Manufacturer: …Type (cylinder/diaphragm)^note: …Model: …Lever length (l): … mm

1.4.Automatic brake adjustment device:Manufacturer (name and address): …Make: …Type: …Version: …

2.Record of test results

2.1.Performance of the automatic brake adjustment device

2.1.1.Hot performance of service braking systems determined according to the test defined in point 3.6.2.1. (a) of Appendix 1 to Annex VII of Regulation (EU) 2015/68: … per centorActuator stroke s_A determined according to the test defined in point 3.6.2.1. (b) of Appendix 1 to Annex VII of Regulation (EU) 2015/68: … mm

2.1.2.Free running according to point 3.6.3. of Appendix 1 to Annex VII of Regulation (EU) 2015/68: yes / no^note

3.Name of Technical Service/Type Approval Authority^note conducting the test: …

4.Date of test: …

5.This test has been carried out and the results reported in accordance with paragraph 3.6.2 of Appendix 1 to Annex VII of Regulation (EU) 2015/68

6.At the end of test mentioned in point 5 the requirements of point 2.2.2.8.1. of Annex I to Regulation (EU) 2015/68 were deemed to be: Fulfilled / Not fulfilled^note

7.Technical Service^note carrying out the testSigned: … Date: …

8.Approval Authority^noteSigned: … Date: …

Test report No. …

Appendix 3

Test report on inertia-braking system control device

1.Manufacturer …

10.The control device described above complies/does not comply^note with the requirements of points 3, 4 and 5 of Annex VIII of Regulation (EU) 2015/68.Signed: … Date: …

11.This test has been carried out and the results reported in accordance with relevant provisions of Annex VIII of Regulation (EU) 2015/68.Technical Service^note carrying out the testSigned: … Date: …

12.Approval Authority^noteSigned: … Date: …

2.Make

3.Type

4.Characteristics of towed vehicles for which control device intended by manufacturer:

4.1.mass G′_A = kg

4.2.permissible static vertical force at towing-device head … N

4.3.towed vehicle with rigid drawbar/multi-axled towed vehicle with pivoted drawbar^note

5.Brief description(List of attached plans and dimensioned drawings)

6.Diagram showing principle of control

7.Travel s = … mm

8.Reduction ratio of control device:

8.1.with mechanical transmission device^notei_Ho = from … to…^note

8.2.with hydraulic transmission device^notei_h = from … to…^noteF_HZ^note = … cmTravel of master cylinder s_Hz … mmSpare travel of master cylinder s"_Hz … mm

9.Test results: …

9.1.Efficiencywith mechanical transmission device^note η_H = …with hydraulic transmission device^note η_H = …

9.2.Supplementary force K = … N

9.3.Maximum compressive force D₁ = … N

9.4.Maximum tractive force D₂ = … N

9.5.Force threshold K_A = … N

9.6.Loss of travel and spare travel: …where the position of the drawing device has an effect^note s_o = mm …with a hydraulic-transmission device^note s" = s"_Hz · i_h = … mm

9.7.Effective (useful) travel of control s′ = … mm

9.8.An overload protector according to point 3.6. of Annex VIII of Regulation (EU) 2015/68 is provided/not provided^note

9.8.1.If the overload protector is fitted before the transmission lever of the control device

9.8.1.1.Threshold force of the overload protector D_op = … N

9.8.1.2.Where the overload protector is mechanical^note max. force which the inertia control device can developP′_max/i_Ho = P_{op_max} =… N

9.8.1.3.Where the overload protector is hydraulic^note the pressure which the inertia control device can developp′_max/i_h = p_{op_max} = … N/cm²

9.8.2.If the overload protector is fitted after the transmission lever of the control device

9.8.2.1.Threshold force on the overload protector where the overload protector is mechanical^note … D_op.i_Ho = Nwhere the overload protector is hydraulic^note D_op.i_h = … N

9.8.2.2.Where the overload protector is mechanical^notemax force which the inertia control device can developP′_max = P_{op_max} = … N

9.8.2.3.Where the overload protector is hydraulic^notethe pressure which the inertia control device can developp′_max = p_{op_max} = … N/cm²

Appendix 4

Test report on the brake

1.Manufacturer …

10.The above brake does / does not^note conform to the requirements of paragraphs 3 and 6 of the testing conditions for vehicles fitted with inertia braking systems described in Annex VIII of Regulation (EU) 2015/68.The brake may / may not^note be used for an inertia braking system without an overload protector.Date: … Signature: …

12.Approval Authority^noteDate: … Signature: …

2.Make …

3.Type …

4.Permissible ‘maximum mass’ per wheel G_Bo = … kg

5.Braking torque M* (as specified by the manufacturer according to point 2.2.23. of Annex VIII of Regulation (EU) 2015/68) = … Nm

6.Dynamic tyre rolling radiusR_min = … m; R_max = … m

7.Brief description(List of plans and dimensioned drawings)

8.Diagram showing principle of brake

9.Test result:

9.10.Service brake performance when the towed vehicle moves rearwards (see figures 6 and 7 of Appendix 1 to Annex VIII of Regulation (EU) 2015/68)

9.10.1.Maximum Fig 6 braking torque M_r = … Nm

9.10.1.AMaximum Fig 7 braking torque M_r = … Nm

9.10.2.Maximum permissible travel s_r = … mm

9.10.2.AMaximum permissible fluid volume absorbed V_r = … cm³

9.11.Further brake characteristics when the towed vehicle moves rearwards (see figures 6 and 7 of Appendix 1 to Annex VIII of Regulation (EU) 2015/68)

9.11.1.Brake-retraction force P_or = … N

9.11.1.ABrake-retraction pressure p_or = … N/cm²

9.11.2.Brake characteristic ρ_r = … m

9.11.2.ABrake characteristic ρ′_r = … m

9.12.Tests according to point 7.5. of Annex VIII of Regulation (EU) 2015/68, if applicable (corrected to take account of the rolling resistance corresponding to 0,01 · g · G_Bo)

9.12.1.Brake test Type-0Test speed = … km/hBraking ratio = …%Control force = … N

9.12.2.Brake test Type-ITest speed = … km/hSustained braking ratio = … %Braking time = … minutesHot performance = … %(expressed as a per cent of the above Type-0 test result in point 9.12.1.)Control force = … N

mechanical brake^note	hydraulic brake^note
9.1.Reduction ratioi_g =…^note^note	9.1.A.Reduction ratioi′_g =…^note
9.2.Lift (application travel)s_B = … mm	9.2.A.Lift (application travel)s_B = … m
9.3.Prescribed lift(prescribed applicationtravel) s_B* = … mm	9.3.A.Prescribed lift(prescribed applicationtravel) s_B* = … mm
9.4.Retraction forceP_o = … N	9.4.A.Retraction pressurep_o= … N/cm²
9.5.Coefficient (characteristic)ρ = … m	9.5.A.Coefficient (characteristic)ρ′ = … m
9.6.An overload protector according to point 3.6. of Annex VIII of Regulation (EU) 2015/68 is/is not provided⁴	9.6.A.An overload protector according to paragraph 3.6. of Annex VIII of Regulation (EU) 2015/68 is/is not provided⁴
9.6.1.Braking torque activating the overload protectorM_op = … Nm	9.6.1.A.Braking torque activating the overload protectorM_op = … Nm
9.7.Force for MP = … N	9.7.A.Pressure for Mp = … N/cm²
	9.8.A.Surface area of wheel cylinderF_RZ = … cm²
	9.9.A.(for disk brakes)Fluid volume absorptionV₆₀ = … cm³

Appendix 5

Test report on the compatibility of the inertia brake control device, the transmission and the brakes on the towed vehicle

1.Control device …described in the attached test report (see test report on inertia-braking system control device)Reduction ratio selected:i_Ho^note =…^note or i_h^note =…^note

2.Brakes described in the attached test report

3.Transmission devices on the towed vehicle

3.1.Brief description with diagram showing principle

3.2.Reduction ratio and efficiency of the mechanical-transmission device on the towed vehiclei_H1^note =…^noteη_H1^note = …

4.Towed vehicle

4.1.Manufacturer

4.10.Brake force B = 0,49 g G_A = N

4.2.Make …

4.3.Type …

4.4.Type of drawbar connection: towed vehicle with rigid drawbar/multi-axled towed vehicle with pivoted drawbar^note

4.5.Number of brakes n =

4.6.Technically permissible maximum mass G_A = kg

4.7.Dynamic tyre rolling radius R* = m

4.8.Permissible thrust on couplingD* = 0,10 g G_A^note = NorD* = 0,067 g G_A^note = N

4.9.Required braking force B* = 0,50 g G_A = N

5.Compatibility - Test results

5.1.Force threshold 100 · K_A/(g · G_A) =

5.2.100 · D₁/(g · G_A) =

5.3.100 · D₂/(g · G_A) = …

5.4.G′A = … kg

5.5.G_B = n · G_Bo = … kg

5.6.Braking torque of the brakes n · M* /(B · R) = …

5.6.1.An overload protector within the meaning of point 3.6. of Annex VIII of Regulation (EU) 2015/68 is / is not^note fitted on the inertia control device / on the brakes^note

5.6.1.1where the overload protector is mechanical on the inertia control device^noten · P* /(iH1 · ηH1 · P′max) = …

5.6.1.2where the overload protector is hydraulic on the inertia control device^notep* / p′max = …

5.6.1.3if the overload protector is on the inertia control device:threshold force Dop/D* = …

5.6.1.4if the overload protector is fitted on the brake:threshold torque n · Mop/(B · R) = …

5.7.Inertia braking system with mechanical transmission device^note

5.7.1.iH = iHo · iH1 = …

5.7.2.ηH = ηHo · ηH1 = …

5.7.3.B Rρ n. Po 1D* K .ηH = …

5.7.4.s′sB * ig = …

5.7.5.Ratio s′/iH = …when the towed vehicle moves rearward

5.7.6.For the braking torque when the towed vehicle moves rearward including rolling resistance0,08 · g · G_A · R = … Nm

5.8.Inertia braking system with hydraulic transmission device^note

5.8.1.ih/FHZ = …

5.8.2.B Rn. ρ′ po 1D* K .ηH = …

5.8.3.s′2sB * n FRZ ig′ = …

5.8.4.s/ih = …

5.8.5.Ratio s′/FHZ = …when the towed vehicle moves rearward

5.8.6.For the braking torque when the towed vehicle moves rearward including rolling resistance0,08 · g · G_A · R = … Nm

6.Differential travel at park brake compensator

6.1.1.Maximum permissible compensator travel (forward) scf = … mm

6.1.2.Maximum permissible compensator travel (rearward) scr = … mm

6.1.3.Maximum permissible differential compensator travel scd = … mm

7.The inertia braking system described above complies/does not comply^note with the requirements of points 3. to 10. of Annex VIII of Regulation (EU) 2015/68.Signature: … Date: …

8.This test has been carried out and the results reported in accordance with relevant provisions of Annex VIII of Regulation (EU) 2015/68.Technical Service^note carrying out the testSignature: … Date: …

Appendix 24

Manufacturer’s declaration on anti-tampering of powertrain and speed-limitation device

2.1.Make(s) (trade name(s) of manufacturer: …

2.4.1.Type^note: …

2.4.2.Variant(s)^note: …

2.4.3.Version(s)^note: …

2.4.4Commercial name(s) (if available): …

2.4.5.Category, subcategory and speed index of vehicle^note: …

2.3.Company name and address of manufacturer: …

2.3.2.Name and address of the manufacturer’s authorised representative (if any)^note: …

Manufacturer’s declaration on anti-tampering of powertrain and speed-limitation device

A duly-completed version of this statement shall be included in the information folder.

The undersigned: [… (full name and position)]

Hereby declares that:

Will not market interchangeable components which could involve an increase in the propulsion performance of the vehicle variant

Place: … Date: …

Signature: … Name and position in the company: …

Explanatory notes relating to Appendix 24 — (Footnote markers, footnotes and explanatory notes not to be stated on the Manufacturer’s declaration)

Appendix 1 — Examples of the statutory plate

2.MODEL B alternative to MODEL A for a T1b-category vehicle

SOFIA TRAKTOR WERKE.T1be6167/2013012235DRH123UPAX0000015590 kgA-1: 2390 kgA-2: 3200 kg		T-1	T-2	T-3
B-1	3000 kg	4000 kg	2000 kg
B-2	3000 kg	4000 kg	2000 kg
B-3	6000 kg	8000 kg	4000 kg
B-4	12000 kg	15000 kg	9000 kg

2.MODEL B alternative to MODEL A for a T1b-category vehicle

SOFIA TRAKTOR WERKE.T1be6167/2013012235DRH123UPAX0000015590 kgA-1: 2390 kgA-2: 3200 kg		T-1	T-2	T-3
B-1	3000 kg	4000 kg	2000 kg
B-2	3000 kg	4000 kg	2000 kg
B-3	6000 kg	8000 kg	4000 kg
B-4	12000 kg	15000 kg	9000 kg

4.MODEL D alternative to MODEL C for stage 1 of a C2a-category vehicle

JEAN NICOLE TRACTORS Ltd.C2a STAGE 1e3167/201314863ZFS159000AZ000055820 kgA-1: 366 kgS-2: 454 kg P: 255 kPa		T-1	T-2	T-3
B-1	1000 kg	2000 kg	1000 kg
B-2	1000 kg	2000 kg	1000 kg
B-3	2000 kg	3000 kg	2000 kg
B-4	4000 kg	5000 kg	4000 kg

4.MODEL D alternative to MODEL C for stage 1 of a C2a-category vehicle

JEAN NICOLE TRACTORS Ltd.C2a STAGE 1e3167/201314863ZFS159000AZ000055820 kgA-1: 366 kgS-2: 454 kg P: 255 kPa		T-1	T-2	T-3
B-1	1000 kg	2000 kg	1000 kg
B-2	1000 kg	2000 kg	1000 kg
B-3	2000 kg	3000 kg	2000 kg
B-4	4000 kg	5000 kg	4000 kg

5.MODEL E for a rigid drawbar R2a-category vehicle
REMORQUES HENSCHLER SA.R2ae12167/201300053YA9EBS370090000052050 kgA-0: 1100 kgA-1: 850 kgA-2: 1200 kg
		T-1	T-2	T-3
B-1	1000 kg	1000 kg	1000 kg
B-2	1000 kg	1000 kg	1000 kg
B-3	2000 kg	2000 kg	2000 kg
B-4	2000 kg	2000 kg	2000 kg

6.MODEL F alternative to MODEL E for a rigid drawbar R2a-category vehicle

REMORQUES HENSCHLER SA.R2ae12167/201300053YA9EBS370090000052050 kgA-0: 1100 kgA-1: 850 kgA-2: 1200 kg’.		T-1	T-2	T-3
B-1	1000 kg	1000 kg	1000 kg
B-2	1000 kg	1000 kg	1000 kg
B-3	2000 kg	2000 kg	2000 kg
B-4	2000 kg	2000 kg	2000 kg

2.MODEL B alternative to MODEL A for a T1b-category vehicle

SOFIA TRAKTOR WERKE.T1be6167/2013012235DRH123UPAX0000015590 kgA-1: 2390 kgA-2: 3200 kg		T-1	T-2	T-3
B-1	3000 kg	4000 kg	2000 kg
B-2	3000 kg	4000 kg	2000 kg
B-3	6000 kg	8000 kg	4000 kg
B-4	12000 kg	15000 kg	9000 kg

2.MODEL B alternative to MODEL A for a T1b-category vehicle

SOFIA TRAKTOR WERKE.T1be6*167/2013*012235DRH123UPAX0000015590 kgA-1: 2390 kgA-2: 3200 kg

T-1

T-2

T-3

B-1

3000 kg

4000 kg

2000 kg

B-2

3000 kg

4000 kg

2000 kg

B-3

6000 kg

8000 kg

4000 kg

B-4

12000 kg

15000 kg

9000 kg

2.MODEL B alternative to MODEL A for a T1b-category vehicle

SOFIA TRAKTOR WERKE.T1be6167/2013012235DRH123UPAX0000015590 kgA-1: 2390 kgA-2: 3200 kg		T-1	T-2	T-3
B-1	3000 kg	4000 kg	2000 kg
B-2	3000 kg	4000 kg	2000 kg
B-3	6000 kg	8000 kg	4000 kg
B-4	12000 kg	15000 kg	9000 kg

2.MODEL B alternative to MODEL A for a T1b-category vehicle

SOFIA TRAKTOR WERKE.T1be6*167/2013*012235DRH123UPAX0000015590 kgA-1: 2390 kgA-2: 3200 kg

T-1

T-2

T-3

B-1

3000 kg

4000 kg

2000 kg

B-2

3000 kg

4000 kg

2000 kg

B-3

6000 kg

8000 kg

4000 kg

B-4

12000 kg

15000 kg

9000 kg

4.MODEL D alternative to MODEL C for stage 1 of a C2a-category vehicle

JEAN NICOLE TRACTORS Ltd.C2a STAGE 1e3167/201314863ZFS159000AZ000055820 kgA-1: 366 kgS-2: 454 kg P: 255 kPa		T-1	T-2	T-3
B-1	1000 kg	2000 kg	1000 kg
B-2	1000 kg	2000 kg	1000 kg
B-3	2000 kg	3000 kg	2000 kg
B-4	4000 kg	5000 kg	4000 kg

4.MODEL D alternative to MODEL C for stage 1 of a C2a-category vehicle

JEAN NICOLE TRACTORS Ltd.C2a STAGE 1e3*167/2013*14863ZFS159000AZ000055820 kgA-1: 366 kgS-2: 454 kg P: 255 kPa

T-1

T-2

T-3

B-1

1000 kg

2000 kg

1000 kg

B-2

1000 kg

2000 kg

1000 kg

B-3

2000 kg

3000 kg

2000 kg

B-4

4000 kg

5000 kg

4000 kg

4.MODEL D alternative to MODEL C for stage 1 of a C2a-category vehicle

JEAN NICOLE TRACTORS Ltd.C2a STAGE 1e3167/201314863ZFS159000AZ000055820 kgA-1: 366 kgS-2: 454 kg P: 255 kPa		T-1	T-2	T-3
B-1	1000 kg	2000 kg	1000 kg
B-2	1000 kg	2000 kg	1000 kg
B-3	2000 kg	3000 kg	2000 kg
B-4	4000 kg	5000 kg	4000 kg

4.MODEL D alternative to MODEL C for stage 1 of a C2a-category vehicle

JEAN NICOLE TRACTORS Ltd.C2a STAGE 1e3*167/2013*14863ZFS159000AZ000055820 kgA-1: 366 kgS-2: 454 kg P: 255 kPa

T-1

T-2

T-3

B-1

1000 kg

2000 kg

1000 kg

B-2

1000 kg

2000 kg

1000 kg

B-3

2000 kg

3000 kg

2000 kg

B-4

4000 kg

5000 kg

4000 kg

5.MODEL E for a rigid drawbar R2a-category vehicle
REMORQUES HENSCHLER SA.R2ae12167/201300053YA9EBS370090000052050 kgA-0: 1100 kgA-1: 850 kgA-2: 1200 kg
		T-1	T-2	T-3
B-1	1000 kg	1000 kg	1000 kg
B-2	1000 kg	1000 kg	1000 kg
B-3	2000 kg	2000 kg	2000 kg
B-4	2000 kg	2000 kg	2000 kg

5.MODEL E for a rigid drawbar R2a-category vehicle

REMORQUES HENSCHLER SA.R2ae12*167/2013*00053YA9EBS370090000052050 kgA-0: 1100 kgA-1: 850 kgA-2: 1200 kg

T-1

T-2

T-3

B-1

1000 kg

B-2

1000 kg

B-3

2000 kg

B-4

2000 kg

6.MODEL F alternative to MODEL E for a rigid drawbar R2a-category vehicle

REMORQUES HENSCHLER SA.R2ae12167/201300053YA9EBS370090000052050 kgA-0: 1100 kgA-1: 850 kgA-2: 1200 kg’.		T-1	T-2	T-3
B-1	1000 kg	1000 kg	1000 kg
B-2	1000 kg	1000 kg	1000 kg
B-3	2000 kg	2000 kg	2000 kg
B-4	2000 kg	2000 kg	2000 kg

6.MODEL F alternative to MODEL E for a rigid drawbar R2a-category vehicle

REMORQUES HENSCHLER SA.R2ae12*167/2013*00053YA9EBS370090000052050 kgA-0: 1100 kgA-1: 850 kgA-2: 1200 kg’.

T-1

T-2

T-3

B-1

1000 kg

B-2

1000 kg

B-3

2000 kg

B-4

2000 kg