Commission Decision 2010/115/EU

law://eu/dec/2010/115@2026-11-15

Contents

THE EUROPEAN COMMISSION,Having regard to the Treaty on the Functioning of the European Union,Having regard to Directive 2000/53/EC of the European Parliament and of the Council of 18 September 2000 on end-of-life vehicles^note, and in particular Article 4(2)(b) thereof,Whereas:

(1)Directive 2000/53/EC prohibits the use of lead, mercury, cadmium or hexavalent chromium in materials and components of vehicles put on the market after 1 July 2003, other than in cases listed in Annex II to that Directive and under the conditions specified therein. Pursuant to Article 4(2)(b) of Directive 2000/53/EC, Annex II to that Directive should be adapted to scientific and technical progress by the Commission on a regular basis.

(2)Annex II to Directive 2000/53/EC lists vehicle materials and components exempted from the prohibition set out in Article 4(2)(a) of that Directive. Vehicles put on the market before the expiry date of a given exemption may contain lead, mercury, cadmium or hexavalent chromium in materials and components listed in Annex II to Directive 2000/53/EC. Commission Decision 2008/689/EC of 1 August 2008 amending Annex II to Directive 2000/53/EC of the European Parliament and of the Council on end-of-life vehicles^note specifies that in the case of solder in electronic circuit boards and other electrical applications except on glass, described in point (8)(a), and solder in electrical applications on glass, described in point (8)(b), the exemptions should be reviewed in 2009.

(3)Technical and scientific assessment has demonstrated that these two exemptions should be split into 10 more specific applications. Out of these, five materials and components containing lead should continue to be temporarily exempted from the prohibition set out in Article 4(2)(a) of Directive 2000/53/EC, since the use of these substances in those specific materials and components is still technically or scientifically unavoidable. It is therefore appropriate to prolong the expiry date of these exemptions until the use of the prohibited substances becomes avoidable.

(4)Five other materials and components containing lead should continue to be exempted from the prohibition set out in Article 4(2)(a) of Directive 2000/53/EC without an expiry date since the use of these substances in those specific materials and components is technically or scientifically unavoidable and no viable alternatives are envisaged in the near future. These exemptions should be reviewed in 2014 in the light of technical and scientific progress to assess when the use of these substances will become avoidable. The exemption concerning lead in solders in electrical glazing applications on glass except for soldering in laminated glazing should be reviewed by 1 January 2012 since substitutes for this application exist but their technical properties need to be further tested and confirmed.

(5)In the case of lead and lead compounds in components in bonding agents for elastomers in power-train applications containing up to 0,5 % lead by weight, the exemption should not be prolonged because the use of lead in this type of applications has become avoidable.

(6)Annex II to Directive 2000/53/EC provides that spare parts put on the market after 1 July 2003 which are used for vehicles put on the market before 1 July 2003 are exempted from the prohibition set out in Article 4(2)(a) of Directive 2000/53/EC. This exemption allows for the repair of vehicles put on the market before the entry into force of the prohibition of Article 4(2)(a) with spare parts meeting the same quality and safety requirements as the parts with which they were originally equipped.

(7)Spare parts for vehicles put on the market after 1 July 2003 but before the expiry date of a given exemption under Annex II to Directive 2000/53/EC are not covered by that exemption. Hence, spare parts for those vehicles must be heavy metal free, even if they are used to replace parts which originally contained heavy metals.

(8)In certain cases it is technically impossible to repair vehicles with spare parts other than original ones as this would require changes in dimensional and functional properties of entire vehicle systems. Such spare parts cannot fit into the vehicle systems originally manufactured with parts containing heavy metals and these vehicles cannot be repaired and may need to be prematurely disposed of. For reasons of consumer safety and environmental benefits derived from the extension of the product’s lifetime it is appropriate to allow the repair of these vehicle components with the original parts.

(9)Directive 2000/53/EC should therefore be amended accordingly.

(10)The measures provided for in this Decision are in accordance with the opinion of the Committee established under Article 18(1) of Directive 2006/12/EC of the European Parliament and of the Council of 5 April 2006 on waste^note,

HAS ADOPTED THIS DECISION:

Article 1 #

Annex II to Directive 2000/53/EC is replaced by the text set out in the Annex to this Decision.

Article 2 #

This Decision is addressed to the Member States.

Annex II

Materials and components exempt from Article 4(2)(a)
Materials and components	Scope and expiry date of the exemption	To be labelled or made identifiable in accordance with Article 4(2)(b)(iv)
1.Steel for machining purposes and galvanised steel containing up to 0,35 % lead by weight
2(a).Aluminium for machining purposes with a lead content up to 2 % by weight	As spare parts for vehicles put on the market before 1 July 2005
2(b).Aluminium with a lead content up to 1,5 % by weight	As spare parts for vehicles put on the market before 1 July 2008
2(c).Aluminium with a lead content up to 0,4 % by weight
3.Copper alloy containing up to 4 % lead by weight
4(a).Bearing shells and bushes	As spare parts for vehicles put on the market before 1 July 2008
4(b).Bearing shells and bushes in engines, transmissions and air conditioning compressors	1 July 2011 and after that date as spare parts for vehicles put on the market before 1 July 2011
5.Batteries		X
6.Vibration dampers		X
7(a).Vulcanising agents and stabilisers for elastomers in brake hoses, fuel hoses, air ventilation hoses, elastomer/metal parts in the chassis applications, and engine mountings	As spare parts for vehicles put on the market before 1 July 2005
7(b).Vulcanising agents and stabilisers for elastomers in brake hoses, fuel hoses, air ventilation hoses, elastomer/metal parts in the chassis applications, and engine mountings containing up to 0,5 % lead by weight	As spare parts for vehicles put on the market before 1 July 2006
7(c).Bonding agents for elastomers in power-train applications containing up to 0,5 % lead by weight	As spare parts for vehicles put on the market before 1 July 2009
8(a).Lead in solders to attach electrical and electronic components to electronic circuit boards and lead in finishes on terminations of components other than electrolyte aluminium capacitors, on component pins and on electronic circuit boards	Vehicles type approved before 1 January 2016 and spare parts for these vehicles	X^note
8(b).Lead in solders in electrical applications other than soldering on electronic circuit boards or on glass	Vehicles type approved before 1 January 2011 and spare parts for these vehicles	X^note
8(c).Lead in finishes on terminals of electrolyte aluminium capacitors	Vehicles type approved before 1 January 2013 and spare parts for these vehicles	X^note
8(d).Lead used in soldering on glass in mass airflow sensors	Vehicles type approved before 1 January 2015 and spare parts of such vehicles	X^note
8(e).Lead in high melting temperature type solders (i.e. lead-based alloys containing 85 % by weight or more lead)	^note	X^note
8(f).Lead in compliant pin connector systems	^note	X^note
8(g).Lead in solders to complete a viable electrical connection between semiconductor die and carrier within integrated circuit flip chip packages	^note	X^note
8(h).Lead in solder to attach heat spreaders to the heat sink in power semiconductor assemblies with a chip size of at least 1 cm² of projection area and a nominal current density of at least 1 A/mm² of silicon chip area	^note	X^note
8(i).Lead in solders in electrical glazing applications on glass except for soldering in laminated glazing	Vehicles type approved before 1 January 2013 and spare parts for these vehicles^note	X^note
8(j).Lead in solders for soldering in laminated glazing	^note	X^note
9.Valve seats	As spare parts for engine types developed before 1 July 2003
10.Electrical components which contain lead in a glass or ceramic matrix compound except glass in bulbs and glaze of spark plugs		X^note (for components other than piezo in engines)
11.Pyrotechnic initiators	Vehicles type-approved before 1 July 2006 and spare parts for these vehicles
12(a).Corrosion preventive coatings	As spare parts for vehicles put on the market before 1 July 2007
12(b).Corrosion preventive coatings related to bolt and nut assemblies for chassis applications	As spare parts for vehicles put on the market before 1 July 2008
13.Absorption refrigerators in motor caravans
14(a).Discharge lamps for headlight application	Vehicles type approved before 1 July 2012 and spare parts for these vehicles
14(b).Fluorescent tubes used in instrument panel displays	Vehicles type approved before 1 July 2012 and spare parts for these vehicles
15.Batteries for electrical vehicles	As spare parts for vehicles put on the market before 31 December 2008

Notes:A maximum concentration value up to 0,1 % by weight and in homogeneous material, for lead, hexavalent chromium and mercury and up to 0,01 % by weight in homogeneous material for cadmium shall be tolerated.The reuse of parts of vehicles which were already on the market at the date of expiry of an exemption shall be allowed without limitation since it is not covered by Article 4(2)(a).Spare parts put on the market after 1 July 2003 which are used for vehicles put on the market before 1 July 2003 shall be exempted from the provisions of Article 4(2)(a)^note.

Commission Decision 2010/115/EU

Commission Decision 2010/115/EU

Article 1 #

Article 2 #

Annex II

Connections

History · 2 versions

Article 1 #

Article 2 #

Annex II

Key facts

Article 1#

Article 2#

Annex II

Connections

History · 2 versions

Article 1#

Article 2#

Annex II

Key facts

Article 1 #

Article 2 #

Article 1 #

Article 2 #